iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61310-3:2000

(Main)

Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators

Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators

Specifies safety-related requirements for actuators, operated by the hand or by other parts of the human body, at the man-machine interface. Gives general requirements for: - the standard direction of movement for actuators; - the arrangement of an actuator in relation to other actuators; - the correlation between an action and its final effects. Based on EN 60447, but is also applicable to non-electrotechnical technologies. Covers single actuators as well as groups of actuators forming part of an assembly.

Sicherheit von Maschinen - Anzeigen, Kennzeichen und Bedienen -- Teil 3: Anforderungen an die Anordnung und den Betrieb von Bedienteilen (Stellteilen)

Sécurité des machines - Indication, marquage et manoeuvre -- Partie 3: Spécifications sur la position et le fonctionnement des organes de service

Spécifie des règles relatives à la sécurité applicables aux organes de service (organes de commande actionnées à la main ou par d'autres parties du corps humain) au niveau de l'interface homme-machine. Donne des prescriptions générales sur: - la direction normalisée du mouvement des organes de services; - la disposition d'un organe de service par rapport à d'autres organes de service; - la corrélation entre une action et ses efffets finaux. Est basée sur la EN 60447, mais elle est aussi applicable aux technologies non-électrotechniques. Couvre aussi bien les organes de service seuls que les groupes d'organes faisant partie d'un jeu.

Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators

General Information

Status
Withdrawn
Publication Date
31-Aug-2000
Withdrawal Date
14-Sep-2020
ICS
13.110 - Safety of machinery
Technical Committee
MOV - Measuring equipment for electromagnetic quantities
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
15-Sep-2020
Due Date
08-Oct-2020
Completion Date
15-Sep-2020
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
98/37/EC - Machinery
Mandate
BC/CEN/13-88 - BC/CEN/13-88
Ref Project
EN 61310-3:1999 - Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators

Relations

Revised
SIST EN 61310-3:2008 - Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators
Effective Date
14-Dec-2010
Replaced By
SIST EN 61310-3:2008 - Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators
Effective Date
28-Jan-2023
Replaced By
SIST EN 61310-3:2008 - Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators
Effective Date
07-Jun-2022
Replaced By
SIST EN 61310-3:2008 - Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the location and operation of actuators
Effective Date
01-Dec-2010

Buy Standard

EN 61310-3:2000EN 61310-3:2000
PreviousNext
Standard
EN 61310-3:2000
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61310-3:2000
01-september-2000
Safety of machinery - Indication, marking and actuation - Part 3: Requirements for
the location and operation of actuators
Safety of machinery - Indication, marking and actuation -- Part 3: Requirements for the
location and operation of actuators
Sicherheit von Maschinen - Anzeigen, Kennzeichen und Bedienen -- Teil 3:
Anforderungen an die Anordnung und den Betrieb von Bedienteilen (St
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 62061:2021(Main)
Safety of machinery - Functional safety of safety-related control systems (IEC 62061:2021)
EN IEC 62061:2021

This International Standard specifies requirements and makes recommendations for the design,
integration and validation of safety-related control systems (SCS) for machines. It is applicable
to control systems used, either singly or in combination, to carry out safety functions on
machines that are not portable by hand while working, including a group of machines working
together in a co-ordinated manner.
This document is a machinery sector specific standard within the framework of IEC 61508 (all
parts).
The design of complex programmable electronic subsystems or subsystem elements is not
within the scope of this document. This is in the scope of IEC 61508 or standards linked to it;
see Figure 1.
NOTE 1 Elements such as systems on chip or microcontroller boards are considered complex programmable
electronic subsystems.
The main body of this sector standard specifies general requirements for the design, and
verification of a safety-related control system intended to be used in high/continuous demand
mode.
This document:
– is concerned only with functional safety requirements intended to reduce the risk of
hazardous situations;
– is restricted to risks arising directly from the hazards of the machine itself or from a group
of machines working together in a co-ordinated manner;
NOTE 2 Requirements to mitigate risks arising from other hazards are provided in relevant sector standards.
For example, where a machine(s) is part of a process activity, additional information is available in IEC 61511.
This document does not cover
– electrical hazards arising from the electrical control equipment itself (e.g. electric shock –
see IEC 60204-1);
– other safety requirements necessary at the machine level such as safeguarding;
– specific measures for security aspects – see IEC TR 63074.
This document is not intended to limit or inhibit technological advancement.
Figure 1 illustrates the scope of this document.

  • Standard
    148 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    141 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61010-2-202:2021(Main)
Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-202: Particular requirements for electrically operated valve actuators (IEC 61010-2-202:2020)
EN IEC 61010-2-202:2021

IEC 61010-2-202:2020 is available as IEC 61010-2-202:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61010-2-202:2020 constitutes Part 2-202 of a planned series of standards on industrial-process measurement, control and automation equipment. Safety terms of general use are defined in IEC 61010-1. More specific terms are defined in each part. This part incorporates the safety related requirements of electrically operated valve ACTUATORs and SOLENOIDs. This document does not cover functional safety aspects of electrically operated ACTUATORs and SOLENOIDs.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61496-2:2020(Amendment)
Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2020)
EN IEC 61496-2:2020

This part of IEC 61496 specifies requirements for the design, construction and testing of
electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part
of a safety-related system, employing active opto-electronic protective devices (AOPDs) for
the sensing function. Special attention is directed to features which ensure that an
appropriate safety-related performance is achieved. An ESPE can include optional safetyrelated
functions, the requirements for which are given in Annex A of IEC 61496-1:2020 and
of this document.
This document does not specify the dimensions or configurations of the detection zone and its
disposition in relation to hazardous parts for any particular application, nor what constitutes a
hazardous state of any machine. It is restricted to the functioning of the ESPE and how it
interfaces with the machine.
Excluded from this document are AOPDs employing radiation at wavelengths outside the
range 400 nm to 1 500 nm.
This document can be relevant to applications other than those for the protection of persons,
for example, the protection of machinery or products from mechanical damage. In those
applications, additional requirements can be necessary, for example, when the materials that
are to be recognized by the sensing function have different properties from those of persons.
This document does not deal with electromagnetic compatibility (EMC) emission
requirements.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61496-1:2020(Amendment)
Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests (IEC 61496-1:2020)
EN IEC 61496-1:2020

This part of IEC 61496 specifies general requirements for the design, construction and testing
of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect
persons or part of a person as part of a safety-related system. Special attention is directed to
functional and design requirements that ensure an appropriate safety-related performance is
achieved. An ESPE can include optional safety-related functions, the requirements for which
are given in Annex A.
NOTE "Non-contact" means that physical contact is not required for sensing.
This document is intended to be used with a subsequent part of IEC 61496 that provides
particular requirements based on the sensing technology.
EXAMPLE This document and IEC 61496-2 are used for AOPDs; this document and IEC 61496-3 are used for
AOPDDRs.
Where a part covering the sensing technology does not exist, IEC TS 62998-1 is used.
Where the IEC 61496 series does not contain all necessary provisions, IEC TS 62998-1 is
used.
It is an additional possibility to combine those aspects covered by the IEC 61496 series in
addition to IEC TS 62998-1.
This document does not specify the dimensions or configuration of the detection zone and its
disposition in relation to hazards in any particular application, nor what constitutes a
hazardous state of any machine. It is restricted to the functioning of the ESPE and how it
interfaces with the machine.
While a data interface can be used to control optional safety-related ESPE functions
(Annex A), this document does not provide specific requirements. Requirements for these
safety-related functions can be determined by consulting other standards (for example,
IEC 61508 (all parts), IEC 62046, IEC 62061, and ISO 13849-1).
This document can be relevant to applications other than those for the protection of persons,
for example for the protection of machinery or products from mechanical damage. In those
applications, different requirements can be appropriate, for example when the materials that
have to be recognized by the sensing function have different properties from those of
persons.
This document does not deal with requirements for ESPE functions not related to the
protection of persons (e.g. using sensing unit data for navigation).
This document does not deal with electromagnetic compatibility (EMC) emission
requirements.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CLC IEC/TR 61511-4:2020(Main)
Functional safety - Safety instrumented systems for the process industry sector - Part 4: Explanation and rationale for changes in IEC 61511-1 from Edition 1 to Edition 2 (IEC/TR 61511-4:2020)
CLC IEC/TR 61511-4:2020

This part of IEC 61511, which is a Technical Report,
•   specifies the rationale behind all clauses and the relationship between them,
•   raises awareness for the most common misconceptions and misinterpretations of the clauses and the changes related to hem,
•   explains the differences between Ed. 1 and Ed. 2 of IEC 61511-1 and the reasons behind the changes,
•   presents high level summaries of how to fulfil the requirements of the clauses, and
•   explains differences in terminology between IEC 61508-4:2010 and IEC 61511-1 Ed. 2.

  • Technical report
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62745:2017/A11:2020(Amendment)
Safety of machinery - Requirements for cableless control systems of machinery
EN 62745:2017/A11:2020

IEC 62745:2017(E) specifies requirements for the functionality and interfacing of cableless (for example, radio, infra-red) control systems that provide communication between operator control station(s) and the control system of a machine. Specific requirements are included for such operator control stations that are portable by the operator.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61310-2:2008
Safety of machinery - Indication, marking and actuation -- Part 2: Requirements for marking
EN 61310-2:2008

This part of IEC 61310 specifies requirements for the marking of machinery. It gives general rules on marking for identification of machinery, for safe use related to mechanical and electrical hazards, and for the avoidance of hazards arising from incorrect connections.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CLC IEC/TR 61511-0:2019(Main)
Functional safety - safety instrumented systems for the process industry sector - Part 0: Functional safety for the process industry and IEC 61511
CLC IEC/TR 61511-0:2019

This part of IEC 61511 provides an overview of the other three parts of IEC 61511.

  • Technical report
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60204-11:2019(Main)
Safety of machinery - Electrical equipment of machines – Part 11: Requirements for equipment for voltages above 1 000 V AC or 1 500 V DC and not exceeding 36 kV(IEC 60204-11:2018)
EN IEC 60204-11:2019

This part of IEC 60204 applies to electrical and electronic equipment and systems to
machines, including a group of machines working together in a co-ordinated manner, which
operate at nominal voltages above 1 000 V AC or 1 500 V DC and not exceeding 36 kV AC or
DC with nominal frequencies not exceeding 60 Hz.
In this document, the term HV equipment also covers the LV equipment forming an integral
part of the equipment operating at high voltage. The requirements in this document primarily
cover the parts operating at high-voltage except where explicitly stated otherwise.
NOTE 1 LV equipment not forming part of the HV equipment is covered by IEC 60204-1:2016.
NOTE 2 In this document, the term "electrical" includes both electrical and electronic matters (i.e. electrical
equipment means both the electrical and the electronic equipment).
NOTE 3 This document does not apply to independent high-voltage power supply installations for which separate
IEC standards exist.
The electrical equipment covered by this document commences at the point of connection of
the supply to the electrical equipment of the machine (see 5.1).
NOTE 4 For the requirements for high-voltage power supply installations, see IEC 61936-1.
This document is a generic safety standard. It does not cover all the requirements (e.g.
guarding, interlocking or control) which are needed or required by other standards or
regulations in order to safeguard personnel from hazards other than electrical hazards. Each
type of machine has unique requirements to be accommodated to provide adequate safety.
NOTE 5 In some machines the high-voltage power supply can be produced by a step-up transformer
(autotransformer), supplied by a low-voltage system (e.g. by a LV generator).
NOTE 6 In the context of this document, the term "person" refers to any individual; "personnel" are those persons
who are assigned and instructed by the user or his agent(s) in the use and care of the machine in question.
This part of IEC 60204 specifically includes, but is not limited to, machines as defined in 3.29
(Annex A lists examples of machines whose electrical equipment can be covered by this
document).
For protection against electric shock from high-voltage equipment, this document refers to
IEC 61936-1. When it comes to low-voltage equipment, this document refers to
IEC 602041:
2016.
NOTE 7 High- and low-voltage standards use different terms regarding protection against electric shock. Whereas
high-voltage standards use the terms “direct contact” and “indirect contact”, low-voltage standards correspondingly
use “basic protection” and “fault protection”.
Additional and special requirements can apply to the electrical equipment of machines that
– are used in the open air (i.e. outside buildings or other protective structures);
– use, process or produce potentially explosive material (e.g. paint or sawdust);
– are used in potentially explosive and/or flammable atmospheres;
– have special risks when producing or using certain materials;
– are used in mines.
Hazards as a result of noise and vibration are excluded from the scope of this document.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61496-3:2019(Main)
Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR) (IEC 61496-3:2018)
EN IEC 61496-3:2019

This part of IEC 61496 specifies additional requirements for the design, construction and
testing of electro-sensitive protective equipment (ESPE) designed specifically to detect
persons or parts of persons as part of a safety-related system, employing active optoelectronic
protective devices responsive to diffuse reflection (AOPDDRs) for the sensing
function. Special attention is directed to requirements which ensure that an appropriate
safety-related performance is achieved. An ESPE can include optional safety-related
functions, the requirements for which are given both in Annex A of this document and in
Annex A of IEC 61496-1:2012.
This document does not specify the dimensions or configurations of the detection zone and its
disposition in relation to hazardous parts for any particular application, nor what constitutes a
hazardous state of any machine. It is restricted to the functioning of the ESPE and how it
interfaces with the machine.
AOPDDRs are devices that have either
– one or more detection zone(s) specified in two dimensions (AOPDDR-2D), or
– one or more detection zone(s) specified in three dimensions (AOPDDR-3D)
wherein radiation in the near infrared range is emitted by an emitting element(s). When the
emitted radiation impinges on an object (for example, a person or part of a person), a portion
of the emitted radiation is reflected to a receiving element(s) by diffuse reflection. This
reflection is used to determine the position of the object.
Opto-electronic devices that perform only a single one-dimensional spot-like distance
measurement, for example, optical proximity switches, are not covered by this document.
This document does not address those aspects required for complex classification or
differentiation of the object detected.
This document does not address requirements and tests for outdoor application.
Excluded from this document are AOPDDRs employing radiation with the peak of wavelength
outside the range 820 nm to 950 nm, and those employing radiation other than that generated
by the AOPDDR itself. For sensing devices that employ radiation of wavelengths outside this
range, this document can be used as a guide. This document is relevant for AOPDDRs having
a minimum detectable object size in the range from 30 mm to 200 mm.
This document can be relevant to applications other than those for the protection of persons,
for example, for the protection of machinery or products from mechanical damage. In those
applications, different requirements can be appropriate, for example when the materials that
have to be recognized by the sensing function have different properties from those of persons
and their clothing.
This document does not deal with electromagnetic compatibility (EMC) emission requirements.

  • Standard
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day