SIST EN 13042-5:2004/kprA1:2009
(Amendment)Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 5: Presses
Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 5: Presses
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Hohlglas - Sicherheitsanforderungen - Teil 5: Pressen
Machines et installations pour la production, le façonnage et la transformation du verre creux - Exigences de sécurité - Partie 5: Presses
Stroji in obrati za proizvodnjo, obdelavo in predelavo votlega stekla - Varnostne zahteve - 5. del: Stiskalnice
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13042-5:2004/kprA1:2009
01-februar-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo votlega stekla - Varnostne
zahteve - 5. del: Stiskalnice
Machines and plants for the manufacture, treatment and processing of hollow glass -
Safety requirements - Part 5: Presses
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Hohlglas -
Sicherheitsanforderungen - Teil 5: Pressen
Machines et installations pour la production, le façonnage et la transformation du verre
creux - Exigences de sécurité - Partie 5: Presses
Ta slovenski standard je istoveten z: EN 13042-5:2003/prA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
SIST EN 13042-5:2004/kprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13042-5:2004/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13042-5:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13042-5:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
December 2008
ICS 81.100
English Version
Machines and plants for the manufacture, treatment and
processing of hollow glass - Safety requirements - Part 5:
Presses
Machines et installations pour la production, le façonnage Maschinen und Anlagen zur Herstellung, Be- und
et la transformation du verre creux - Exigences de sécurité Verarbeitung von Hohlglas - Sicherheitsanforderungen -
- Partie 5: Presses Teil 5: Pressen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13042-5:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13042-5:2003/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13042-5:2004/kprA1:2009
EN 13042-5:2003/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Introduction.4
2 Modifications to the Scope .4
3 Modifications to Clause 2 .4
4 Modification to Clause 3 .5
5 Modifications to Clause 5 .5
6 Addition of 5.1.5.6
7 Modification to 5.4.1 .6
8 Modification to 5.4.2 .6
9 Modification to 5.6 .6
10 Modification to 5.8 .6
11 Modification to 5.9 .7
12 Modification to 5.11 .7
13 Addition of 5.20.7
14 Modification to Clause 6 .8
15 Modification to Clause 7 .8
16 Modifications to 7.1 .8
17 Modifications to 7.2 .9
18 Modification to Annex ZA .10
19 Addition of Annex ZB .11
20 Modifications to the Bibliography.11
2
---------------------- Page: 4 ----------------------
SIST EN 13042-5:2004/kprA1:2009
EN 13042-5:2003/prA1:2008 (E)
Foreword
This document (EN 13042-5:2003/prA1:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 13042-5:2004/kprA1:2009
EN 13042-5:2003/prA1:2008 (E)
1 Modification to the Introduction
st
1 paragraph:
Replace the reference to “EN 1070” with “EN ISO 12100”.
2 Modifications to the Scope
Replace the text of 1.2 with the following:
"This standard deals with all significant hazards, hazardous situations and events relevant to glass presses
when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the
manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or re-
duce risks from the significant hazards commissioning, operation and maintenance.”
In 1.3, replace:
“prEN 13042-3” with “EN 13042-3”.
In 1.4, replace:
“prEN 13042-1” with “EN 13042-1” and “prEN 13042-2” with “EN 13042-2”.
3 Modifications to Clause 2
st
Replace the 1 paragraph with the following:
“The following referenced documents are indispensable for the application of this document. For dated refer-
ences, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.”
Delete the following references:
“EN 292-1, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology,
methodology
EN 292-2, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles
and specifications
EN 292-2:1991/A1:1995, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles and specifications
EN 418, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design
EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design
EN 1050:1996, Safety of machinery — Principles for risk assessment
EN 1070:1998, Safety of machinery — Terminology”.
Replace the reference "EN 60204-1:1997" with the following:
4
---------------------- Page: 6 ----------------------
SIST EN 13042-5:2004/kprA1:2009
EN 13042-5:2003/prA1:2008 (E)
“EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1:2005, modified)”.
Add the following references:
“EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Engineering method in an essen-
tially free field over a reflecting plane (ISO 11201:1995)
EN ISO 11202:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Survey method in situ
(ISO11202:1995)
EN ISO 11204:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Method requiring environmental
corrections (ISO 11204:1995)
EN ISO 11688-1:1998, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning (ISO/TR 11688- 1:1995)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Tech-
nical principles (ISO 12100-2:2003)
EN ISO 13849-1:2008, Safety of machi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.