SIST EN 62676-3:2015
(Main)Video surveillance systems for use in security applications - Part 3: Analog and digital video interfaces
Video surveillance systems for use in security applications - Part 3: Analog and digital video interfaces
IEC 62676-3:2013 specifies physical, electrical and software interface (non-IP) specifications of analog and digital video interface in video surveillance systems (so far called CCTV) applications. Video interfaces are used both for connection and transmission of surveillance video, audio and control signals. This International Standard applies strictly to Video Surveillance Systems. This standard is based on broadcast television standards and other standards, and it defines the minimum requirements for analog and digital video interfaces to meet VSS's requirements, interoperability and de facto practice.
Videoüberwachungsanlagen für Sicherungsanwendungen - Teil 3: Analoge und digitale Videoschnittstellen
Systèmes de vidéosurveillance destinés à être utilisés dans les applications de sécurité - Partie 3: Interfaces vidéo analogiques et vidéo numériques
La CEI 62676-3:2013 spécifie les spécifications relatives aux interfaces physiques, électriques et logicielles (non-IP) de l'interface vidéo analogique et numérique dans les applications des systèmes de vidéosurveillance (auparavant appelés CCTV). Les interfaces vidéo sont utilisées la connexion et aussi la transmission des signaux de vidéo surveillance, des signaux audio et des signaux de commande. La présente Norme internationale s'applique strictement aux systèmes de vidéosurveillance. La présente norme est basée sur des normes de télévision par diffusion et d'autres normes. Elle définit également les exigences minimales pour les interfaces vidéo analogiques et numériques satisfassent aux exigences concernant les VSS, à l'interopérabilité et la pratique de facto.
Video nadzorni sistemi za varnostne aplikacije - 3. del: Analogni in digitalni video vmesniki (IEC 62676-3:2013)
Standard IEC 62676-3:2013 določa fizične in električne specifikacije ter specifikacije vmesnika programske opreme (brez IP-ja) analognih in digitalnih video vmesnikov v video nadzornih sistemih (ki so se doslej imenovali CCTV) za varnostne aplikacije. Video vmesniki se uporabljajo za povezovanje in prenos video, zvočnih in kontrolnih nadzornih signalov. Ta mednarodni standard dosledno velja za video nadzorne sisteme. Ta standard temelji na standardih za digitalno televizijsko radiodifuzijo in drugih standardih ter določa minimalne zahteve za analogne in digitalne video vmesnike, da izpolnijo zahteve VSS, interoperabilnosti in dejanske prakse.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62676-3:2015
01-april-2015
Video nadzorni sistemi za varnostne aplikacije - 3. del: Analogni in digitalni video
vmesniki (IEC 62676-3:2013)
Video surveillance systems for use in security applications - Part 3: Analog and digital
video interfaces
Videoüberwachungsanlagen für Sicherungsanwendungen - Teil 3: Analoge und digitale
Videoschnittstellen
Systèmes de vidéosurveillance destinés à être utilisés dans les applications de sécurité -
Partie 3: Interfaces vidéo analogiques et vidéo numériques
Ta slovenski standard je istoveten z: EN 62676-3:2015
ICS:
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
33.160.40 Video sistemi Video systems
SIST EN 62676-3:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62676-3:2015
---------------------- Page: 2 ----------------------
SIST EN 62676-3:2015
EUROPEAN STANDARD EN 62676-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2015
ICS 13.320
English Version
Video surveillance systems for use in security applications -
Part 3: Analog and digital video interfaces
(IEC 62676-3:2013)
Systèmes de vidéosurveillance destinés à être utilisés Videoüberwachungsanlagen für Sicherungsanwendungen -
dans les applications de sécurité - Teil 3: Analoge und digitale Videoschnittstellen
Partie 3: Interfaces vidéo analogiques et vidéo numériques (IEC 62676-3:2013)
(IEC 62676-3:2013)
This European Standard was approved by CENELEC on 2015-01-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62676-3:2015 E
---------------------- Page: 3 ----------------------
SIST EN 62676-3:2015
EN 62676-3:2015 - 2 -
Foreword
This document (EN 62676-3:2015) consists of the text of IEC 62676-3:2013 prepared by
IEC/TC 79 "Alarm and electronic security systems".
The following dates are fixed:
(dop) 2016-01-05
• latest date by which the document has to be
implemented
at national level by publication of an identical
national standard or by endorsement
• latest date by which the national standards conflicting (dow) 2018-01-05
with the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62676-3:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60874-1:2011 NOTE Harmonized as EN 60874-1:2012 (not modified).
IEC 61169-8 NOTE Harmonized as EN 61169-8.
IEC 62676-1-2 NOTE Harmonized as EN 62676-1-2.
IEC 62676-2-1 NOTE Harmonized as EN 62676-2-1.
IEC 62676-2-2 NOTE Harmonized as EN 62676-2-2.
IEC 62676-2-3 NOTE Harmonized as EN 62676-2-3.
---------------------- Page: 4 ----------------------
SIST EN 62676-3:2015
- 3 - EN 62676-3:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year
1)
IEC 60068-1 1988 Environmental testing - EN 60068-1 1994
Part 1: General and guidance
IEC 62315-1 2003 DTV profiles for uncompressed digital EN 62315-1 2003
video interfaces -
Part 1: General
VESA Industry Standards & Guidelines for Computer Display Monitor Timing (DMT) Version 1
Revision 11
VESA Video Signal Standard (VSIS) Version 1, Rev. 2
1)
Superseded by EN 60068-1:2014 (IEC 60068-1:2013): DOW = 2016-11-11.
---------------------- Page: 5 ----------------------
SIST EN 62676-3:2015
---------------------- Page: 6 ----------------------
SIST EN 62676-3:2015
IEC 62676-3
®
Edition 1.0 2013-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Video surveillance systems for use in security applications –
Part 3: Analog and digital video interfaces
Systèmes de vidéosurveillance destinés à être utilisés dans les applications de
sécurité –
Partie 3: Interfaces vidéo analogiques et vidéo numériques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX W
ICS 13.320 ISBN 978-2-8322-0991-2
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62676-3:2015
– 2 – 62676-3 © IEC:2013
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Abbreviations . 12
4 General information . 13
4.1 General principles . 13
4.2 Physical interfaces . 14
4.2.1 General . 14
4.2.2 Camera signal interface . 14
4.2.3 Display equipment video interface . 15
4.2.4 Video processing and control equipment interface . 16
4.2.5 Video/audio encoder/decoder interface . 16
4.2.6 Fiber optical transmission equipment interface . 17
4.2.7 Wireless transmission equipment interface . 17
4.2.8 Alarm equipment interface . 17
4.3 Software interfaces for network access layer . 17
5 Electrical interfaces . 17
5.1 General . 17
5.2 Analog video signal interface . 17
5.2.1 Composite video . 17
5.2.2 Y/C video. 18
5.2.3 YPbPr analog component video . 18
5.2.4 RGB analog component video . 18
5.3 Digital video signal interface . 20
5.3.1 HDMI . 20
5.3.2 DVI . 20
5.3.3 DisplayPort (DP) . 20
5.3.4 SDI video. 20
5.4 Control signal interface. 21
5.4.1 RS-232 . 21
5.4.2 RS-485 . 21
6 Detailed analog (composite) video signal transmission requirements . 21
6.1 General . 21
6.2 Video input and output . 21
6.2.1 Source and load impedance . 21
6.2.2 Return loss . 21
6.2.3 Input and output signal levels . 21
6.2.4 Input signal frequency . 22
6.2.5 Input and output DC voltage . 22
6.3 Insertion gain . 22
6.4 Signal to noise ratio. 22
6.5 Interference . 22
6.6 Luminance non-linearity . 22
---------------------- Page: 8 ----------------------
SIST EN 62676-3:2015
62676-3 © IEC:2013 – 3 –
6.7 Chrominance to luminance gain inequality . 22
6.8 Chrominance to luminance delay inequality . 23
6.9 Differential gain . 23
6.10 Differential phase . 23
7 Analog video signal transmission test conditions . 23
7.1 General . 23
7.2 Test equipment . 23
7.2.1 General . 23
7.2.2 Test equipment . 23
7.2.3 Test signals . 23
7.2.4 Equipment set-up . 24
7.3 Laboratory conditions . 24
8 Analog video signal transmission performance tests . 24
8.1 Input and output signal levels . 24
8.1.1 Principle . 24
8.1.2 Preparation of the test . 24
8.1.3 Test procedure . 24
8.1.4 Criterion for compliance . 24
8.2 Insertion gain . 24
8.2.1 Principle . 24
8.2.2 Preparation of the test . 24
8.2.3 Test procedure . 25
8.2.4 Criterion for compliance . 25
8.3 Input and output impedance . 25
8.3.1 Principle . 25
8.3.2 Preparation of the test . 25
8.3.3 Test procedure . 25
8.3.4 Criterion for compliance . 26
8.4 DC voltage at the output . 26
8.4.1 Principle . 26
8.4.2 Preparation of the test . 26
8.4.3 Test procedure . 26
8.4.4 Criterion for compliance . 26
8.5 Chrominance to luminance gain and delay inequality . 26
8.5.1 Principle . 26
8.5.2 Preparation of the test . 27
8.5.3 Test procedure . 27
8.5.4 Criterion for compliance . 27
8.6 Signal to noise ratio. 27
8.6.1 Principle . 27
8.6.2 Preparation of the test . 27
8.6.3 Test procedure . 27
8.6.4 Criterion for compliance . 27
8.7 Interference . 27
8.7.1 Principle . 27
8.7.2 Preparation of the test . 27
8.7.3 Test procedure . 28
8.7.4 Criterion for compliance . 28
8.8 Luminance non-linearity . 28
---------------------- Page: 9 ----------------------
SIST EN 62676-3:2015
– 4 – 62676-3 © IEC:2013
8.8.1 Principle . 28
8.8.2 Preparation of the test . 28
8.8.3 Test procedure . 28
8.8.4 Criterion for compliance . 28
8.9 Differential gain . 28
8.9.1 Principle . 28
8.9.2 Preparation of the test . 28
8.9.3 Test procedure . 28
8.9.4 Criterion for compliance . 29
8.10 Differential phase . 29
8.10.1 Principle . 29
8.10.2 Preparation of the test . 29
8.10.3 Test procedure . 29
8.10.4 Criterion for compliance . 29
8.11 Documentation . 29
Annex A (normative) Test patterns . 30
Annex B (normative) Chrominance to luminance gain and delay charts . 33
Bibliography . 35
Figure 1 – Interface hierarchy of analog and digital video device . 13
Figure 2 – Connection scheme of VSS devices . 14
Figure 3 – Impedance measuring circuit . 25
Figure A.1 – Signal A . 30
Figure A.2 – Signal B . 30
Figure A.3 – Signal C . 31
Figure A.4 – Signal D1 . 31
Figure A.5 – Signal D2 . 32
Figure A.6 – Signal E . 32
Figure B.1 – Chrominance to luminance amplitude and delay errors . 33
Figure B.2 – The Rosman nomogram . 34
Table 1 – Summary of display monitor timings – Standards and guidelines . 19
---------------------- Page: 10 ----------------------
SIST EN 62676-3:2015
62676-3 © IEC:2013 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
VIDEO SURVEILLANCE SYSTEMS FOR USE
IN SECURITY APPLICATIONS –
Part 3: Analog and digital video interfaces
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62676-3 has been prepared by technical committee 79: Alarm and
electronic security systems.
The text of this standard is based on the following documents:
FDIS Report on voting
79/417/FDIS 79/429/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 11 ----------------------
SIST EN 62676-3:2015
– 6 – 62676-3 © IEC:2013
A list of all parts in the IEC 62676 series, published under the general title Video surveillance
systems for use in security applications, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN 62676-3:2015
62676-3 © IEC:2013 – 7 –
INTRODUCTION
The IEC Technical Committee 79 in charge of alarm and electronic security systems together
with many governmental organizations, test houses and equipment manufacturers has defined
a common framework for video surveillance transmission in order to achieve interoperability
between products.
The IEC 62676 series of standards on video surveillance systems is divided into four
independent parts:
Part 1: System requirements
Part 2: Video transmission protocols
Part 3: Analog and digital video interfaces
Part 4: Application guidelines
Each part offers its own clauses on scope, references, definitions and requirements.
This IEC Standard Part 3 of IEC 62676 specifies physical, electrical interface and software
specifications of analog and digital video interfaces in Video Surveillance Systems (VSS), so
far called Closed Circuit Television (CCTV).
For analog video interfaces, analog video signal such as Composite Video is still the most
commonly used interface among Video Surveillance Systems equipment. Though broadcast
television industry has adopted composite video standards (e.g. NTSC, PAL), they have not
been consistently applied for Video Surveillance Systems applications and it is important to
standardize the interface to ensure interoperability between Video Surveillance Systems.
Also, as broadcast is moving towards digital, there are many possibilities to improve the
performance with these new Video Interfaces compared to conventional Analog Video
Interface, and thus it is important to standardize those new Analog Video interface and also
Digital Video Interface to ensure interoperability among Video Surveillance Systems using
these new interfaces.
For digital video interface, IEC 62676-1-2, IEC 62676-2-1, IEC 62676-2-2 and IEC 62676-2-3
focus on video transmission and compressed IP video transmissions by specifying internet (IP)
and higher layers. IEC 62676-3 completes the communication layer specification by
describing uncompressed digital video and two lowest layer protocols such as physical and
network access.
---------------------- Page: 13 ----------------------
SIST EN 62676-3:2015
– 8 – 62676-3 © IEC:2013
VIDEO SURVEILLANCE SYSTEMS FOR USE
IN SECURITY APPLICATIONS –
Part 3: Analog and digital video interfaces
1 Scope
This Part of IEC 62676 specifies physical, electrical and software interface (non-IP)
specifications of analog and digital video interface in video surveillance systems (so far called
CCTV) applications. Video interfaces are used both for connection and transmission of
surveillance video, audio and control signals. Through video interfaces, video surveillance
systems can be put together by connecting various components such as image capturing
devices, image handling devices, etc. This International Standard ensures interoperability
among various video surveillance components.
This International Standard applies strictly to Video Surveillance Systems. This standard is
based on broadcast television standards and other standards, and it defines the minimum
requirements for analog and digital video interfaces to meet VSS’s requirements,
interoperability and de facto practice.
2 Normative re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.