SIST EN 1239:2011
(Main)Adhesives - Freeze-thaw stability
Adhesives - Freeze-thaw stability
This European Standard specifies a method for the evaluation of the freeze-thaw stability of adhesives, their basic constituents and related products.
This test has no significance if the sample does not freeze under the test conditions.
Klebstoffe - Gefrier-Auftau-Stabilität
Diese Europäische Norm legt ein Verfahren zur Beurteilung der Gefrier-Auftau-Stabilität von Klebstoffen, ihrer Grundbestandteile sowie verwandter Produkte fest.
Diese Prüfung ist ohne Bedeutung für Proben, die unter den Prüfbedingungen nicht gefrieren.
Adhésifs - Stabilité au gel-dégel
La présente Norme européenne spécifie une méthode d'évaluation de la stabilité au gel-dégel des adhésifs, de leurs constituants de base et des produits connexes.
Cet essai n'a de signification que si l'échantillon gèle dans les conditions d’essai.
Lepila - Stabilnost pri cikličnem zamrzovanju in odmrzovanju
Ta evropski standard opredeljuje metodo za ocenjevanje stabilnosti lepil pri cikličnem zamrzovanju in odmrzovanju, njihove osnovne sestavine in sorodne proizvode.
Ta preskus je brezpredmeten če vzorec ni zamrznjen pod preskusnimi pogoji.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Klebstoffe - Gefrier-Auftau-StabilitätAdhésifs - Stabilité au gel-dégelAdhesives - Freeze-thaw stability83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 1239:2011SIST EN 1239:2011en,fr,de01-julij-2011SIST EN 1239:2011SLOVENSKI
STANDARDSIST EN 1239:19991DGRPHãþD
SIST EN 1239:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1239
April 2011 ICS 83.180 Supersedes EN 1239:1998English Version
Adhesives - Freeze-thaw stability
Adhésifs - Stabilité au gel-dégel
Klebstoffe - Gefrier-Auftau-Stabilität This European Standard was approved by CEN on 10 March 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1239:2011: ESIST EN 1239:2011
EN 1239:2011 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Principle .45Apparatus .46Sampling, examination and preparation of samples .57Procedure .58Expression of results and classification .59Test report .6 SIST EN 1239:2011
EN 1239:2011 (E) 3 Foreword This document (EN 1239:2011) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1239:1998. The main modifications regarding the previous version are in the Normative References and 8.1. SAFETY STATEMENT — Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. ENVIRONMENTAL STATEMENT — It is understood that some of the material permitted in this standard may have negative environmental impact. As technological advantages lead to acceptable alternatives for these materials, they will be eliminated from this standard to the extent possible. At the end of the test, the user of the standard should take care to carry out an appropriate disposal of the wastes, according to local regulation. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 1239:2011
EN 1239:2011 (E) 4 1 Scope This European Standard specifies a method for the evaluation o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.