F15.15 - Wallcoverings

ABSTRACT
This specification covers the performance, quality, packaging, and marking requirements for flexible wall coverings as a finished product. Also included here are wall preparation and covering installation procedures. The manufacturers shall be responsible for thorough testing and inspection under representative field conditions prior to introduction of new finished products on the market.
SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall coverings as finished products.  
1.1.1 Whenever this specification refers to wall coverings, it is intended also to refer to ceiling coverings of the same type.  
1.1.2 This specification does not apply to wall coverings intended to be applied to exterior walls.  
1.1.3 This specification does not apply to rigid panel products, irrespective of whether or not they include a flexible lining or veneer.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This classification provides criteria by which wall coverings of appropriate use characteristics can be chosen for particular residential and commercial decorating applications.
SCOPE
1.1 This classification covers the classification of wall coverings by use characteristics, that is, according to their serviceability in use, recognizing that certain wall coverings are designed primarily for decorative effect, while other wall coverings are also designed to achieve a high degree of serviceability.  
1.1.1 This classification applies to any wall covering but some sections apply specifically to vinyl-coated wall covering materials.  
1.1.2 Whenever this classification refers to wall coverings, it is intended also to refer to ceiling coverings of the same type.  
1.1.3 This classification does not apply to wall coverings intended to be applied to exterior walls.  
1.1.4 This classification does not apply to rigid panel products, irrespective of whether or not they include a flexible lining or veneer.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard.  
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This classification provides criteria by which wall coverings of appropriate use characteristics can be chosen for particular residential and commercial decorating applications.
SCOPE
1.1 This classification covers the classification of wall coverings by use characteristics, that is, according to their serviceability in use, recognizing that certain wall coverings are designed primarily for decorative effect, while other wall coverings are also designed to achieve a high degree of serviceability.  
1.1.1 This classification applies to all wall coverings but some sections apply specifically to vinyl-coated wall covering materials.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard.  
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the performance, quality, packaging, and marking requirements for flexible wall coverings as a finished product. Also included here are wall preparation and covering installation procedures. The manufacturers shall be responsible for thorough testing and inspection under representative field conditions prior to introduction of new finished products on the market.
SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall coverings as finished products.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard.

SIGNIFICANCE AND USE
This classification provides criteria by which wall covering of appropriate use characteristics can be chosen for particular residential and commercial decorating applications.
SCOPE
1.1 This classification covers the classification of wall covering by use characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed primarily for decorative effect, while other wall covering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This classification provides criteria by which wall covering of appropriate use characteristics can be chosen for particular residential and commercial decorating applications.
SCOPE
1.1 This classification covers the classification of wall covering by use characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed primarily for decorative effect, while other wall covering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the performance, quality, packaging, and marking requirements for flexible wall coverings as a finished product. Also included here are wall preparation and covering installation procedures. The manufacturers shall be responsible for thorough testing and inspection under representative field conditions prior to introduction of new finished products on the market.
SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall covering as a finished product.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers the performance, quality, packaging, and marking requirements for flexible wall coverings as a finished product. Also included here are wall preparation and covering installation procedures. The manufacturers shall be responsible for thorough testing and inspection under representative field conditions prior to introduction of new finished products on the market.
SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall covering as a finished product.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

SIGNIFICANCE AND USE
This classification provides criteria by which wall covering of appropriate use characteristics can be chosen for particular residential and commercial decorating applications.
SCOPE
1.1 This classification covers the classification of wall covering by use characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed primarily for decorative effect, while other wall covering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions
This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This classification covers the classification of wall covering by use characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed primarily for decorative effect, while other wall covering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This classification covers the classification of wall covering by durability characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed primarily for decorative effect, while other wall covering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the performance, quality, packaging, and marking requirements for flexible wall coverings as a finished product. Also included here are wall preparation and covering installation procedures. The manufacturers shall be responsible for thorough testing and inspection under representative field conditions prior to introduction of new finished products on the market.
SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall covering as a finished product.

SCOPE
1.1 This classification covers the classification of wallcovering by durability characteristics, that is, according to its serviceability in use, recognizing that certain wallcovering is designed primarily for decorative effect, while other wallcovering is also designed to achieve a high degree of serviceability.
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are provided for information only.
1.3 The flammability test in this classification should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use
This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall covering as a finished product.

SCOPE
1.1 This classification covers the classification of wallcovering by durability characteristics, that is, according to its serviceability in use, recognizing that certain wallcovering is designed primarily for decorative effect, while other wallcovering is also designed to achieve a high degree of serviceability.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric values given in parentheses are provided for information only.  
1.3 The flammability test in this classification should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.