85.080 - Paper products
ICS 85.080 Details
Paper products
Papierwaren. Kartonagen
Produits en papier
Papirni izdelki
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 85.080 - Paper products
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers.
This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard.
This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers.
This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard.
This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for the determination of the flat crush resistance of corrugated fibreboard used in the manufacture of shipping containers. This document is applicable to single-faced and single-wall (double-faced) corrugated fibreboard. This document is not applicable to double-wall (double-double-faced) corrugated fibreboard and to microflute corrugated fibreboard, since the end-point of the test is not clearly defined or observable.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies the requirements for permanent paper intended for documents. It is applicable to unprinted papers. It is not applicable to boards.
NOTE 1 The terms paper and board are defined in ISO 4046-3.
This document is not intended for judging the permanence of papers stored under hostile conditions, such as high humidity that can promote microbiological attack, excessive heat, radiation (light or other), high levels of atmospheric pollutants, or the influence of water.
NOTE 2 For information on International Standards on paper permanence (ISO 9706), on archival paper permanence and durability (ISO 11108), and on paper stability for general graphic applications (ISO 20494), refer to Annex D.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for permanent paper intended for documents. It is applicable to unprinted papers. It is not applicable to boards.
NOTE 1 The terms paper and board are defined in ISO 4046-3.
This document is not intended for judging the permanence of papers stored under hostile conditions, such as high humidity that can promote microbiological attack, excessive heat, radiation (light or other), high levels of atmospheric pollutants, or the influence of water.
NOTE 2 For information on International Standards on paper permanence (ISO 9706), on archival paper permanence and durability (ISO 11108), and on paper stability for general graphic applications (ISO 20494), refer to Annex D.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a basic laboratory test method for deinkability of woodfree printed paper products as a mixture under alkaline conditions by means of single stage flotation deinking and fatty acid-based collector chemistry. The woodfree printed paper product of interest is tested as a mixture containing 10 % by weight of the woodfree printed paper with the balance comprising a mixture of printed wood-containing paper.
- Standard23 pagesEnglish languagesale 15% off
This document covers physical properties and manufacturing requirements for envelopes having an address window and the flap on the front side once the flap has been sealed, hereafter the flap side. It covers the main design features of the reverse envelope, notably of the flap and address window, and the materials used for the manufacturing thereof. It applies to reverse envelopes with advertising or communication printed on the plain side, eventually on its entire surface.
This document covers empty envelopes, but also finished mailpieces that have been properly inserted, addressed and franked (reverse mailpieces) and are submitted to Postal Operators. In particular, reverse mailpieces will be compliant with relevant Postal standards applicable in the member states.
By extension, these requirements also apply to non-window envelopes used for reverse mailpieces and having the address printed on the flap side.
This document does not apply to:
- envelopes with a large window on the plain side (opposite to the flap) as these are already common and widely accepted,
- paper requirements to ensure print quality (except for the postage mark and address) and notably colour rendering.
- Technical specification15 pagesEnglish languagesale 10% offe-Library read for1 day
This document covers physical properties and manufacturing requirements for envelopes having an address window and the flap on the front side once the flap has been sealed, hereafter the flap side. It covers the main design features of the reverse envelope, notably of the flap and address window, and the materials used for the manufacturing thereof. It applies to reverse envelopes with advertising or communication printed on the plain side, eventually on its entire surface.
This document covers empty envelopes, but also finished mailpieces that have been properly inserted, addressed and franked (reverse mailpieces) and are submitted to Postal Operators. In particular, reverse mailpieces will be compliant with relevant Postal standards applicable in the member states.
By extension, these requirements also apply to non-window envelopes used for reverse mailpieces and having the address printed on the flap side.
This document does not apply to:
- envelopes with a large window on the plain side (opposite to the flap) as these are already common and widely accepted,
- paper requirements to ensure print quality (except for the postage mark and address) and notably colour rendering.
- Technical specification15 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps.
This document is not applicable to cases where impurities and contraries are determined.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps.
This document is not applicable to cases where impurities and contraries are determined.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation. Currently, two types of tensile-strength-testing apparatus are commercially available, one where the test piece is positioned vertically and, for the other, horizontally. This document applies for both. For vertical tensile-strength-testing apparatus, a device that is held in the lower grip of the tensile-strength-testing apparatus, called a Finch Cup, is used to achieve the wetting. For horizontal tensile-strength-testing apparatus, the soaking device is placed between the two clamps. This document is not applicable to cases where impurities and contraries are determined.
- Standard15 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing.
This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary.
It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the testing procedures for the instrumental determination of the opacity of tissue paper or tissue products by diffuse reflectance using a paper backing. This document contains specific instructions for the preparation of test pieces of single-ply and multi-ply products, where special preparation/procedures might be necessary. It can be used to determine the opacity of tissue paper and tissue products containing fluorescent whitening agents, provided the UV content of the radiation incident on the test piece has been adjusted to conform to that in the CIE illuminant C using a fluorescent reference standard provided by an authorized laboratory as described in ISO 2470-1.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in this document.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation.
This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper.
The calculation of perforation efficiency is also specified in this document.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the tensile strength of perforated lines of tissue paper. It uses a tensile-testing apparatus operating with a constant rate of elongation. This method is only used for measuring machine-direction tensile strength, that is for cross-direction perforations on tissue paper. The calculation of perforation efficiency is also specified in this document.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.
This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard.
It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.
This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard.
It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a non-waxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis. This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard. It is applicable to all corrugated fibreboard flute types if no buckling and/or tipping occurs during measurement. This method is also applicable to test samples taken from corrugated cases and other converted products.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the surface friction of tissue paper and tissue products using a contact-type surface tester.
- Standard11 pagesEnglish languagesale 15% off
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed in indoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary. NOTE The properties called D65 brightness and colour are measured with an instrument adjusted to a much higher UV content than that specified in this document.
- Standard10 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the tensile strength, stretch at maximum force and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation. It also specifies the method of calculating the tensile index and the tensile energy absorption index.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary.
NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions can be necessary. NOTE The properties called ISO brightness and colour with C/2° (indoor daylight) are measured with an instrument adjusted to a much lower UV content than that specified in this document. The measurements of ISO brightness and colour with C/2° (indoor daylight) are described in ISO 12625-15.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method to assess the disintegration of tissue paper and tissue products when subjected to mechanical agitation in water.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
This document defines a method for measuring the decolouration capability of commercial products, produced using paper and board dyed in mass and/or printed with dye inks. This document does not apply to paper printed with pigment inks.
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This document specifies a basic laboratory test method for deinkability, applicable to any kind of printed paper product, under alkaline conditions by means of single stage flotation deinking and fatty acid-based collector chemistry.
- Standard23 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products.
For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using an A-flute geometry.
The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.
NOTE ISO 7263-2 describes a method to determine the flat crush resistance using a B-flute geometry.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using a B-flute geometry.
The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.
NOTE ISO 7263-1 describes a method to determine the flat crush resistance using an A-flute geometry.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products.
It permits the use of a common terminology in industry and commerce.
It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products.
For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products after wetting.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document establishes general principles for the use of terms in the entire working field of tissue paper and tissue products. It permits the use of a common terminology in industry and commerce. It is expressly stated that ISO 15755 applies for the detection of impurities and contraries in tissue paper and tissue products. For the determination of moisture content in tissue paper and tissue products, ISO 287 applies.
- Standard18 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using an A-flute geometry. The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board. NOTE ISO 7263-2 describes a method to determine the flat crush resistance using a B-flute geometry.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document describes a method for the determination of the flat crush resistance of a corrugating medium after laboratory fluting using a B-flute geometry. The procedure is applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board. NOTE ISO 7263-1 describes a method to determine the flat crush resistance using an A-flute geometry.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ISO 12625-6:2016 specifies a test method for the determination of grammage of tissue paper and tissue products.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 12625-6:2016 specifies a test method for the determination of grammage of tissue paper and tissue products.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 12625-6:2016 specifies a test method for the determination of grammage of tissue paper and tissue products.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO 12625-9:2015 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products.
Currently, two types of clamping devices are available on the market with two different diameters, one is with 50 mm and one is with 89 mm. ISO 12625-9:2015 applies for a 50 mm clamping device to be able to measure all sample sizes of tissue paper and tissue products and to be consistent with ISO 12625-11.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 12625-9:2015 specifies a test method for the determination of the resistance to mechanical penetration (ball burst strength procedure) of tissue paper and tissue products.
Currently, two types of clamping devices are available on the market with two different diameters, one is with 50 mm and one is with 89 mm. ISO 12625-9:2015 applies for a 50 mm clamping device to be able to measure all sample sizes of tissue paper and tissue products and to be consistent with ISO 12625-11.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day