F26.03 - Storage and Dispensing Equipment

ABSTRACT
This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines. Materials used in the construction of the machine shall comply with NSF No. 4 and UL Standard 197. Unless otherwise specified, all hardware and fittings shall be corrosion-resistant to ASTM A167 or ASTM A176 or suitably processed to resist corrosion and all threaded parts shall conform to ANSI B1.1.
SCOPE
1.1 This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the material, design, and construction requirements for reach-in refrigerators, freezers, combination refrigerator/freezers, and thaw cabinets that are stationary and of a vertical or horizontal configuration. Products covered by this specification are sorted into type: refrigerator (Type I), freezer (Type II), combination refrigerator/freezer (Type III), and thaw cabinet (Type IV); grade: vertical cabinet (Grade 1) and horizontal cabinet (Grade2); class: modular construction (Class 1) and unitary or single piece construction (Class 2); size; and style: manual loading (Style 1) and roll-in cart loading (Style 2). Materials used for the manufacture of the products shall be new and free of defects or reclaimed or recycled materials having the same quality as new materials and shall comprise of the following: corrosion-resistant steel, non-corrosion resistant steel (mild steel coated with zinc, chrome, nickel, or paint), aluminum alloys, seamless copper tubings, and corrosion-resistant material (for use in hardware, fittings, and fasteners). The product and its components shall be free of dirt, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts, and stampings shall be free of voids, sand pits, blowholes, and sprues. In addition, the assembly shall have no sharp edges or concealed objects that may cause injury. The products shall be tested for compliance to the requirements specified.
SCOPE
1.1 This specification covers the basic design and function of temperature regulated, continuous duty commercial, and marine refrigerators, freezers, combination refrigerator/freezers and thaw cabinets. The equipment will be stationary and of a vertical or horizontal type.  
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this specification to comply with environmental regulations.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial ice cream, soft serve, and shake freezers that freeze and dispense frozen products (dairy, yogurt, custard, etc.) on a continuous basis. The ice cream freezers are classified into types according to frozen product produced, groups according to number of cylinders, styles according to mountability, classes according to condenser type, and grades freezing mechanism, as follows: Type I—soft-serve freezer; Type II—shake freezer; and Type III—combination soft-serve and shake freezer; Group 1—one freezing cylinder; Group 2—two freezing cylinders; Group 3—three freezing cylinders; and Group 4—four freezing cylinders; Style 1—floor mounted; and Style 2—countertop; Class 1—air-cooled condenser; Class 2—liquid-cooled condenser; and Class 3—remote air-cooled condenser; Grade 1—conventional nonheat-treatment freezer; and Grade 2—heat-treatment freezer. The freezers shall conform to electrical, steel fabrication, lubrication, interchangeability, refrigerant, insulation, and other performance and operational requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial ice cream, soft serve, and shake freezers, which freeze and dispense frozen product (dairy, yogurt, custard, etc.) on a continuous basis. Included in this specification are conventional and heat-treatment freezers.  
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this standard to comply with environmental regulations (see 7.5).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks. The beverage dispensers shall be of the following types, classes, styles, and sizes: Types I and II; Classes A and B; Styles A (sizes 1, 2, 3, and 4), B (sizes 1 and 2), and C (size 1). The beverage dispenser shall consist essentially of a base that contains a complete refrigeration system and supports a rigid, transparent, impact resistant, bowl-type beverage container(s) with cover(s). Performance test, pull-down test, energy consumption test, maximum ambient temperature and high humidity test, bowl impact test, and operation production performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial bulk milk dispensers for dispensing milk in commercial and institutional food service establishments. These specified commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinets with lift-up valves used for dispensing refrigerated milks and milk fluid products. Commercial bulk milk dispensers covered in this specification are classified by type, electrical class and size. In this specification, types 1, 1A, 2A, 3A, 4A are determined and covered. For electrical classes of bulk milk dispenser, the classes 1 and 2 are described. Sizes 1 to 3 of milk dispenser are used in this specification to describe commercial bulk milk dispenser. The physical properties of commercial bulk milk dispenser are also covered in this specification wherein the design and manufacturer, the cooling system, the controls, the standards and compliance and the accessories are specified in accordance with agreed requirements and specifications. Sampling, testing, and quality assurance of finished units are also covered in this specification wherein these tests and procedures must be met in accordance with ANSI/UL 471 and NSF/ANSI 20.
SCOPE
1.1 This specification covers commercial bulk milk dispensers which are for dispensing milk in the commercial and institutional food service establishments. These commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinet(s) with lift-up or push-type valves. These units are intended to dispense refrigerated milk and fluid milk products.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers basic design and function of rapid pull down refrigerators or freezers, or a combination of both, sometimes referred to as “blast chillers,” “blast freezers,” or “quick chillers.”  
1.2 This equipment is for professional use in commercial and other similar food service establishments for rapid intermediate chilling or freezing of hot food products cooked to a specific temperature within a specified time period and holding the food at a safe temperature when not engaged in the chilling or freezing process.  
1.3 This standard addresses equipment that is self-contained, manually operated, and has a mechanically refrigerated cabinet(s) of a vertical or horizontal cabinet type. Equipment may be a “reach-in” for stationary or fixed shelving or a “roll-in” for mobile carts. This equipment may also be installed under a service counter.  
1.4 This standard does not cover blast chilling tunnels, continuous blast-chilling and blast freezing equipment, bakery combined freezing and storage units.  
1.5 The standard does not cover “shock freezers” or equipment that uses nitrogen or other consumable products in their function.  
1.6 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this specification to comply with environmental regulations.  
1.7 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial automatic ice making machines used in manufacturing and processing ice, including the attached equipment used in storing and dispensing the produced ice for human consumption. This specification does not apply to icemakers of the tray type, ice vending machines, icemakers and icemaker kits used in household refrigerators or freezers, and block ice manufacturing plants. The ice machines covered here are classified into the following types, grades, classes, and styles: Type I—ice machine with or without ice storage bin; Type II—icemaker-dispenser machine; and Type III—ice dispenser; Grade 1—self-contained air-cooled condenser; Grade 2—self-contained water-cooled condenser; Grade 3—remote water-cooled; and Grade 4—remote air-cooled; Class A—cubed ice; Class B—flaked ice; Class C—nugget ice; and Class D—other ice shapes; Style 1—corrosion-resisting steel cabinet; Style 2—carbon steel cabinet; and Style 3—plastic cabinet. Representative production models of the ice making machines shall pass the performance and operational tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers requirements for commercial automatic ice making equipment. It covers the equipment and devices used in manufacturing and processing ice for human consumption and the attached equipment used in storing and dispensing ice in connection with this equipment.  
1.2 This specification does not apply to icemakers of the tray type, ice vending machines, or icemakers and icemaker kits used in household refrigerators or freezers. This specification is not intended to cover block ice manufacturing plants.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parenthesis are provided for information only.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers counter model, self-contained powdered iced tea dispensers. The tea dispensers shall be of two types, each working with a powdered concentrate that is mixed with potable tap water to give a finished drink. Type I is designed to work with pure tea and Type II is designed to dispense a sugared tea. The dispenser shall be an electromechanical device for dispensing either the pure tea or sugared tea powder and mixing it with tap water upon manual actuation of a momentary-on electrical switch. The instant tea and water shall be mixed in a chamber that will rinse clean at the end of the drink. In order to determine the performance of the dispensers, the following tests shall be performed: energy consumption test, water flow test, ingredient throw test, and humidity test. All components and assemblies of the dispenser shall be free from dirt and other extraneous material such as burrs, slivers, rough die, tool and grind marks, dents, and cracks. Castings and molded parts, if used, shall be free of sand, fins, pits, blowholes, and sprues.
SCOPE
1.1 This specification covers counter model, self-contained powdered iced tea dispensers.  
1.2 The dispenser delivered under this specification shall be the manufacturer's standard product. Each dispenser model furnished by a particular manufacturer under this specification, including parts and assemblies thereof, shall be new and interchangeable.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are given for information only.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines. Materials used in the construction of the machine shall comply with NSF No. 4 and UL Standard 197. Unless otherwise specified, all hardware and fittings shall be corrosion-resistant to ASTM A167 or ASTM A176 or suitably processed to resist corrosion and all threaded parts shall conform to ANSI B1.1.
SCOPE
1.1 This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial ice cream, soft serve, and shake freezers that freeze and dispense frozen products (dairy, yogurt, custard, etc.) on a continuous basis. The ice cream freezers are classified into types according to frozen product produced, groups according to number of cylinders, styles according to mountability, classes according to condenser type, and grades freezing mechanism, as follows: Type I—soft-serve freezer; Type II—shake freezer; and Type III—combination soft-serve and shake freezer; Group 1—one freezing cylinder; Group 2—two freezing cylinders; Group 3—three freezing cylinders; and Group 4—four freezing cylinders; Style 1—floor mounted; and Style 2—countertop; Class 1—air-cooled condenser; Class 2—liquid-cooled condenser; and Class 3—remote air-cooled condenser; Grade 1—conventional nonheat-treatment freezer; and Grade 2—heat-treatment freezer. The freezers shall conform to electrical, steel fabrication, lubrication, interchangeability, refrigerant, insulation, and other performance and operational requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial ice cream, soft serve, and shake freezers, which freeze and dispense frozen product (dairy, yogurt, custard, etc.) on a continuous basis. Included in this specification are conventional and heat-treatment freezers.  
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this standard to comply with environmental regulations (see 7.5).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial bulk milk dispensers for dispensing milk in commercial and institutional food service establishments. These specified commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinets with lift-up valves used for dispensing refrigerated milks and milk fluid products. Commercial bulk milk dispensers covered in this specification are classified by type, electrical class and size. In this specification, types 1, 1A, 2A, 3A, 4A are determined and covered. For electrical classes of bulk milk dispenser, the classes 1 and 2 are described. Sizes 1 to 3 of milk dispenser are used in this specification to describe commercial bulk milk dispenser. The physical properties of commercial bulk milk dispenser are also covered in this specification wherein the design and manufacturer, the cooling system, the controls, the standards and compliance and the accessories are specified in accordance with agreed requirements and specifications. Sampling, testing, and quality assurance of finished units are also covered in this specification wherein these tests and procedures must be met in accordance with ANSI/UL 471 and NSF/ANSI 20.
SCOPE
1.1 This specification covers commercial bulk milk dispensers which are for dispensing milk in the commercial and institutional food service establishments. These commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinet(s) with lift-up or push-type valves. These units are intended to dispense refrigerated milk and fluid milk products.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks. The beverage dispensers shall be of the following types, classes, styles, and sizes: Types I and II; Classes A and B; Styles A (sizes 1, 2, 3, and 4), B (sizes 1 and 2), and C (size 1). The beverage dispenser shall consist essentially of a base that contains a complete refrigeration system and supports a rigid, transparent, impact resistant, bowl-type beverage container(s) with cover(s). Performance test, pull-down test, energy consumption test, maximum ambient temperature and high humidity test, bowl impact test, and operation production performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines. Materials used in the construction of the machine shall comply with NSF No. 4 and UL Standard 197. Unless otherwise specified, all hardware and fittings shall be corrosion-resistant to ASTM A167 or ASTM A176 or suitably processed to resist corrosion and all threaded parts shall conform to ANSI B1.1.
SCOPE
1.1 This specification covers commercial single cup or batch coffee brewers which are used for brewing coffee in commercial and institutional facilities and does not include residential units. This specification is limited to standard coffee brewers and does not include espresso or specialty coffee drink machines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial automatic ice making machines used in manufacturing and processing ice, including the attached equipment used in storing and dispensing the produced ice for human consumption. This specification does not apply to icemakers of the tray type, ice vending machines, icemakers and icemaker kits used in household refrigerators or freezers, and block ice manufacturing plants. The ice machines covered here are classified into the following types, grades, classes, and styles: Type I—ice machine with or without ice storage bin; Type II—icemaker-dispenser machine; and Type III—ice dispenser; Grade 1—self-contained air-cooled condenser; Grade 2—self-contained water-cooled condenser; Grade 3—remote water-cooled; and Grade 4—remote air-cooled; Class A—cubed ice; Class B—flaked ice; Class C—nugget ice; and Class D—other ice shapes; Style 1—corrosion-resisting steel cabinet; Style 2—carbon steel cabinet; and Style 3—plastic cabinet. Representative production models of the ice making machines shall pass the performance and operational tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers requirements for commercial automatic ice making equipment. It covers the equipment and devices used in manufacturing and processing ice for human consumption and the attached equipment used in storing and dispensing ice in connection with this equipment.
1.2 This specification does not apply to icemakers of the tray type, ice vending machines, or icemakers and icemaker kits used in household refrigerators or freezers. This specification is not intended to cover block ice manufacturing plants.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parenthesis are provided for information only.

ABSTRACT
This specification covers counter model, self-contained powdered iced tea dispensers. The tea dispensers shall be of two types, each working with a powdered concentrate that is mixed with potable tap water to give a finished drink. Type I is designed to work with pure tea and Type II is designed to dispense a sugared tea. The dispenser shall be an electromechanical device for dispensing either the pure tea or sugared tea powder and mixing it with tap water upon manual actuation of a momentary-on electrical switch. The instant tea and water shall be mixed in a chamber that will rinse clean at the end of the drink. In order to determine the performance of the dispensers, the following tests shall be performed: energy consumption test, water flow test, ingredient throw test, and humidity test. All components and assemblies of the dispenser shall be free from dirt and other extraneous material such as burrs, slivers, rough die, tool and grind marks, dents, and cracks. Castings and molded parts, if used, shall be free of sand, fins, pits, blowholes, and sprues.
SCOPE
1.1 This specification covers counter model, self-contained powdered iced tea dispensers.
1.2 The dispenser delivered under this specification shall be the manufacturer's standard product. Each dispenser model furnished by a particular manufacturer under this specification, including parts and assemblies thereof, shall be new and interchangeable.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are given for information only.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the material, design, and construction requirements for reach-in refrigerators, freezers, combination refrigerator/freezers, and thaw cabinets that are stationary and of a vertical or horizontal configuration. Products covered by this specification are sorted into type: refrigerator (Type I), freezer (Type II), combination refrigerator/freezer (Type III), and thaw cabinet (Type IV); grade: vertical cabinet (Grade 1) and horizontal cabinet (Grade2); class: modular construction (Class 1) and unitary or single piece construction (Class 2); size; and style: manual loading (Style 1) and roll-in cart loading (Style 2). Materials used for the manufacture of the products shall be new and free of defects or reclaimed or recycled materials having the same quality as new materials and shall comprise of the following: corrosion-resistant steel, non-corrosion resistant steel (mild steel coated with zinc, chrome, nickel, or paint), aluminum alloys, seamless copper tubings, and corrosion-resistant material (for use in hardware, fittings, and fasteners). The product and its components shall be free of dirt, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts, and stampings shall be free of voids, sand pits, blowholes, and sprues. In addition, the assembly shall have no sharp edges or concealed objects that may cause injury. The products shall be tested for compliance to the requirements specified.
SCOPE
1.1 This specification covers the basic design and function of temperature regulated, continuous duty commercial, and marine refrigerators, freezers, combination refrigerator/freezers and thaw cabinets. The equipment will be stationary and of a vertical or horizontal type.
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this specification to comply with environmental regulations.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers commercial bulk milk dispensers for dispensing milk in commercial and institutional food service establishments. These specified commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinets with lift-up valves used for dispensing refrigerated milks and milk fluid products. Commercial bulk milk dispensers covered in this specification are classified by type, electrical class and size. In this specification, types 1, 1A, 2A, 3A, 4A are determined and covered. For electrical classes of bulk milk dispenser, the classes 1 and 2 are described. Sizes 1 to 3 of milk dispenser are used in this specification to describe commercial bulk milk dispenser. The physical properties of commercial bulk milk dispenser are also covered in this specification wherein the design and manufacturer, the cooling system, the controls, the standards and compliance and the accessories are specified in accordance with agreed requirements and specifications. Sampling, testing, and quality assurance of finished units are also covered in this specification wherein these tests and procedures must be met in accordance with ANSI/UL 471 and NSF/ANSI 20
SCOPE
1.1 This specification covers commercial bulk milk dispensers which are for dispensing milk in the commercial and institutional food service establishments. These commercial bulk milk dispensers are self-contained, manually-operated, gravity-fed, mechanically refrigerated cabinet(s) with lift-up or push-type valves. These units are intended to dispense refrigerated milk and fluid milk products.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks. The beverage dispensers shall be of the following types, classes, styles, and sizes: Types I and II; Classes A and B; Styles A (sizes 1, 2, 3, and 4), B (sizes 1 and 2), and C (size 1). The beverage dispenser shall consist essentially of a base that contains a complete refrigeration system and supports a rigid, transparent, impact resistant, bowl-type beverage container(s) with cover(s). Performance test, pull-down test, energy consumption test, maximum ambient temperature and high humidity test, bowl impact test, and operation production performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.
1.2 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial ice cream, soft serve, and shake freezers that freeze and dispense frozen products (dairy, yogurt, custard, etc.) on a continuous basis. The ice cream freezers are classified into types according to frozen product produced, groups according to number of cylinders, styles according to mountability, classes according to condenser type, and grades freezing mechanism, as follows: Type I—soft-serve freezer; Type II—shake freezer; and Type III—combination soft-serve and shake freezer; Group 1—one freezing cylinder; Group 2—two freezing cylinders; Group 3—three freezing cylinders; and Group 4—four freezing cylinders; Style 1—floor mounted; and Style 2—countertop; Class 1—air-cooled condenser; Class 2—liquid-cooled condenser; and Class 3—remote air-cooled condenser; Grade 1—conventional nonheat-treatment freezer; and Grade 2—heat-treatment freezer. The freezers shall conform to electrical, steel fabrication, lubrication, interchangeability, refrigerant, insulation, and other performance and operational requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial ice cream, soft serve, and shake freezers, which freeze and dispense frozen product (dairy, yogurt, custard, etc.) on a continuous basis. Included are conventional and heat-treatment freezers.
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this standard to comply with environmental regulations (see 7.5).
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the material, design, and construction requirements for reach-in refrigerators, freezers, combination refrigerator/freezers, and thaw cabinets that are stationary and of a vertical or horizontal configuration. Products covered by this specification are sorted into type: refrigerator (Type I), freezer (Type II), combination refrigerator/freezer (Type III), and thaw cabinet (Type IV); grade: vertical cabinet (Grade 1) and horizontal cabinet (Grade2); class: modular construction (Class 1) and unitary or single piece construction (Class 2); size; and style: manual loading (Style 1) and roll-in cart loading (Style 2). Materials used for the manufacture of the products shall be new and free of defects or reclaimed or recycled materials having the same quality as new materials and shall comprise of the following: corrosion-resistant steel, non-corrosion resistant steel (mild steel coated with zinc, chrome, nickel, or paint), aluminum alloys, seamless copper tubings, and corrosion-resistant material (for use in hardware, fittings, and fasteners). The product and its components shall be free of dirt, burrs, slivers, tool and grind marks, dents, and cracks. Castings, molded parts, and stampings shall be free of voids, sand pits, blowholes, and sprues. In addition, the assembly shall have no sharp edges or concealed objects that may cause injury. The products shall be tested for compliance to the requirements specified.
SCOPE
1.1 This specification covers the basic design and function of temperature regulated, continuous duty commercial, and marine refrigerators, freezers, combination refrigerator/freezers and thaw cabinets. The equipment will be stationary and of a vertical or horizontal type.
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this specification to comply with environmental regulations.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial automatic ice making machines used in manufacturing and processing ice, including the attached equipment used in storing and dispensing the produced ice for human consumption. This specification does not apply to icemakers of the tray type, ice vending machines, icemakers and icemaker kits used in household refrigerators or freezers, and block ice manufacturing plants. The ice machines covered here are classified into the following types, grades, classes, and styles: Type I—ice machine with or without ice storage bin; Type II—icemaker-dispenser machine; and Type III—ice dispenser; Grade 1—self-contained air-cooled condenser; Grade 2—self-contained water-cooled condenser; Grade 3—remote water-cooled; and Grade 4—remote air-cooled; Class A—cubed ice; Class B—flaked ice; Class C—nugget ice; and Class D—other ice shapes; Style 1—corrosion-resisting steel cabinet; Style 2—carbon steel cabinet; and Style 3—plastic cabinet. Representative production models of the ice making machines shall pass the performance and operational tests, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers requirements for commercial automatic ice making equipment. It covers the equipment and devices used in manufacturing and processing ice for human consumption and the attached equipment used in storing and dispensing ice in connection with this equipment.
1.2 This specification does not apply to icemakers of the tray type, ice vending machines, or icemakers and icemaker kits used in household refrigerators or freezers. This specification is not intended to cover block ice manufacturing plants.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parenthesis are provided for information only.

ABSTRACT
This specification covers counter model, self-contained powdered iced tea dispensers. The tea dispensers shall be of two types, each working with a powdered concentrate that is mixed with potable tap water to give a finished drink. Type I is designed to work with pure tea and Type II is designed to dispense a sugared tea. The dispenser shall be an electromechanical device for dispensing either the pure tea or sugared tea powder and mixing it with tap water upon manual actuation of a momentary-on electrical switch. The instant tea and water shall be mixed in a chamber that will rinse clean at the end of the drink. In order to determine the performance of the dispensers, the following tests shall be performed: energy consumption test, water flow test, ingredient throw test, and humidity test. All components and assemblies of the dispenser shall be free from dirt and other extraneous material such as burrs, slivers, rough die, tool and grind marks, dents, and cracks. Castings and molded parts, if used, shall be free of sand, fins, pits, blowholes, and sprues.
SCOPE
1.1 This specification covers counter model, self-contained powdered iced tea dispensers.
1.2 The dispenser delivered under this specification shall be the manufacturer's standard product. Each dispenser model furnished by a particular manufacturer under this specification, including parts and assemblies thereof, shall be new and interchangeable.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are given for information only.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks. The beverage dispensers shall be of the following types, classes, styles, and sizes: Types I and II; Classes A and B; Styles A (sizes 1, 2, 3, and 4), B (sizes 1 and 2), and C (size 1). The beverage dispenser shall consist essentially of a base that contains a complete refrigeration system and supports a rigid, transparent, impact resistant, bowl-type beverage container(s) with cover(s). Performance test, pull-down test, energy consumption test, maximum ambient temperature and high humidity test, bowl impact test, and operation production performance test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.
1.2 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers commercial ice cream, soft serve, and shake freezers, which freeze and dispense frozen product (dairy, yogurt, custard, etc.) on a continuous basis. Included are conventional and heat-treatment freezers.
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this standard to comply with environmental regulations (see 7.5).
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the design, performance, and certification requirements pertinent to the construction of commercial ice cream, soft serve, and shake freezers that freeze and dispense frozen products (dairy, yogurt, custard, etc.) on a continuous basis. The ice cream freezers are classified into types according to frozen product produced, groups according to number of cylinders, styles according to mountability, classes according to condenser type, and grades freezing mechanism, as follows: Type I—soft-serve freezer; Type II—shake freezer; and Type III—combination soft-serve and shake freezer; Group 1—one freezing cylinder; Group 2—two freezing cylinders; Group 3—three freezing cylinders; and Group 4—four freezing cylinders; Style 1—floor mounted; and Style 2—countertop; Class 1—air-cooled condenser; Class 2—liquid-cooled condenser; and Class 3—remote air-cooled condenser; Grade 1—conventional nonheat-treatment freezer; and Grade 2—heat-treatment freezer. The freezers shall conform to electrical, steel fabrication, lubrication, interchangeability, refrigerant, insulation, and other performance and operational requirements, and should function satisfactorily as specified.
SCOPE
1.1 This specification covers commercial ice cream, soft serve, and shake freezers, which freeze and dispense frozen product (dairy, yogurt, custard, etc.) on a continuous basis. Included are conventional and heat-treatment freezers.
1.2 Equipment covered under this specification may contain a substance (or be manufactured with a substance) that harms public health and environment by destroying ozone in the upper atmosphere. This specification does not purport to address environmental regulations. It is the responsibility of the user of this standard to comply with environmental regulations (see 7.5).
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers counter-top model noncarbonated beverage dispensers that are mechanically refrigerated and have rigid, transparent, impact-resistant containers to afford a visual display of the beverage dispensed. The beverage dispensers covered by this specification are intended to circulate, cool, and dispense noncarbonated beverages such as pulpy juices, frozen concentrates, and syrup drinks.
1.2 The following safety hazard caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers counter model, self-contained powdered iced tea dispensers.  
1.2 The dispenser delivered under this specification shall be the manufacturer's standard product. Each dispenser model furnished by a particular manufacturer under this specification, including parts and assemblies thereof, shall be new and interchangeable.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are given for information only.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers counter-model, self-contained hot rehydrated mashed potato dispensers.  
1.2 The dispenser delivered under this specification shall be the manufacturer's standard product. Each dispenser model furnished by a particular manufacturer under this specification, including parts and assemblies thereof, shall be new and interchangeable.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are for information only.  
1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covers counter-model, self-contained hot rehydrated mashed potato dispensers.
Formerly under the jurisdiction of Committee F26 on Food Service Equipment, this specification was withdrawn in September 2004. This specification is being withdrawn because there has not been any interest in this equipment either from industry or government.