D26.03 - Cold Cleaning

ABSTRACT
This specification establishes the requirements for three grades of 1,1,2-trichloro 1,2,2-trifluoroethane solvent, as follows: Type I, electronic or ultra-clean grade; Type II, standard or vapour-degreasing grade; and Type IIA, general purpose grade packaged in a pressurized container. Each grade shall adhere to individually specified values of the following chemical and physical properties: boiling point at standard barometric pressure; chemical purity; moisture content; chloride ions content; specific aqueous conductance; acid number; and residue content.
SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:  
1.1.1 Type I electronic or ultra-clean grade,  
1.1.2 Type II standard or vapor-degreasing grade, and  
1.1.3 Type IIA general purpose, packaged in a pressurized container grade.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This guide is to be used by anyone developing cleaning requirements for specifications for manufacturing, maintenance, or overhaul. This guide has been designed to be application specific for each cleaning task and to assure the design engineer that the process selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent process(es). This guide allows the industrial or manufacturing engineer to customize the selection of the cleaning product based on the materials of the part being cleaned; the cleanliness required for the subsequent process(es); and the environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.  
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.  
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers technical grade methylene chloride. Technical grade methylene chloride shall conform to the requirements prescribed. Tests shall be performed to determine the property requirements of the material in accordance to the following test methods: appearance; color; specific gravity; distillating range; nonvolatile residue; acidity; water; and free halogens.
SCOPE
1.1 This specification covers technical grade methylene chloride.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: See Guide D3844, Practice D4276, and STP 403A2 for additional important information on solvent handling and solvent properties.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers technical grade methylene chloride. Technical grade methylene chloride shall conform to the requirements prescribed. Tests shall be performed to determine the property requirements of the material in accordance to the following test methods: appearance; color; specific gravity; distillating range; nonvolatile residue; acidity; water; and free halogens.
SCOPE
1.1 This specification covers technical grade methylene chloride.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1: See Guide D3844, Practice D4276, and STP 403A2 for additional important information on solvent handling and solvent properties.

ABSTRACT
This specification establishes the requirements for three grades of 1,1,2-trichloro 1,2,2-trifluoroethane solvent, as follows: Type I, electronic or ultra-clean grade; Type II, standard or vapour-degreasing grade; and Type IIA, general purpose grade packaged in a pressurized container. Each grade shall adhere to individually specified values of the following chemical and physical properties: boiling point at standard barometric pressure; chemical purity; moisture content; chloride ions content; specific aqueous conductance; acid number; and residue content.
SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:  
1.1.1 Type I electronic or ultra-clean grade,  
1.1.2 Type II standard or vapor-degreasing grade, and  
1.1.3 Type IIA general purpose, packaged in a pressurized container grade.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
5.1 This guide is to be used by anyone developing cleaning requirements for specifications for manufacturing, maintenance, or overhaul. This guide has been designed to be application specific for each cleaning task and to assure the design engineer that the process selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent process(es). This guide allows the industrial or manufacturing engineer to customize the selection of the cleaning product based on the materials of the part being cleaned; the cleanliness required for the subsequent process(es); and the environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.  
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.  
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers technical grade methylene chloride. Technical grade methylene chloride shall conform to the requirements prescribed. Tests shall be performed to determine the property requirements of the material in accordance to the following test methods: appearance; color; specific gravity; distillating range; nonvolatile residue; acidity; water; and free halogens.
SCOPE
1.1 This specification covers technical grade methylene chloride.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—See Practices D3844 and D4276 and STP 403A for additional important information on solvent handling and solvent properties.

SIGNIFICANCE AND USE
This guide is to be used by anyone developing cleaning requirements for specifications for manufacturing, maintenance, or overhaul. This guide has been designed to be application specific for each cleaning task and to assure the design engineer that the process selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent process(es). This guide allows the industrial or manufacturing engineer to customize the selection of the cleaning product based on the materials of the part being cleaned; the cleanliness required for the subsequent process(es); and the environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ABSTRACT
This specification establishes the requirements for three grades of 1,1,2-trichloro 1,2,2-trifluoroethane solvent, as follows: Type I, electronic or ultra-clean grade; Type II, standard or vapour-degreasing grade; and Type IIA, general purpose grade packaged in a pressurized container. Each grade shall adhere to individually specified values of the following chemical and physical properties: boiling point at standard barometric pressure; chemical purity; moisture content; chloride ions content; specific aqueous conductance; acid number; and residue content.
SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:
1.1.1 Type I electronic or ultra-clean grade,
1.1.2 Type II standard or vapor-degreasing grade, and
1.1.3 Type IIA general purpose, packaged in a pressurized container grade.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

ABSTRACT
This specification establishes the requirements for three grades of 1,1,2-trichloro 1,2,2-trifluoroethane solvent, as follows: Type I, electronic or ultra-clean grade; Type II, standard or vapour-degreasing grade; and Type IIA, general purpose grade packaged in a pressurized container. Each grade shall adhere to individually specified values of the following chemical and physical properties: boiling point at standard barometric pressure; chemical purity; moisture content; chloride ions content; specific aqueous conductance; acid number; and residue content.
SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:
1.1.1 Type I electronic or ultra-clean grade,
1.1.2 Type II standard or vapor-degreasing grade, and
1.1.3 Type IIA general purpose, packaged in a pressurized container grade.

ABSTRACT
This specification covers technical grade methylene chloride. Technical grade methylene chloride shall conform to the requirements prescribed. Tests shall be performed to determine the property requirements of the material in accordance to the following test methods: appearance; color; specific gravity; distillating range; nonvolatile residue; acidity; water; and free halogens.
SCOPE
1.1 This specification covers technical grade methylene chloride.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1
See Practices D 3844 and D 4276 and STP 403A for additional important information on solvent handling and solvent properties.

SIGNIFICANCE AND USE
This guide is to be used by anyone developing cleaning requirements for specifications for manufacturing, maintenance, or overhaul. This guide has been designed to be application specific for each cleaning task and to assure the design engineer that the process selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent process(es). This guide allows the industrial or manufacturing engineer to customize the selection of the cleaning product based on the materials of the part being cleaned; the cleanliness required for the subsequent process(es); and the environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.

ABSTRACT
This specification establishes the requirements for three grades of 1,1,2-trichloro 1,2,2-trifluoroethane solvent, as follows: Type I, electronic or ultra-clean grade; Type II, standard or vapour-degreasing grade; and Type IIA, general purpose grade packaged in a pressurized container. Each grade shall adhere to individually specified values of the following chemical and physical properties: boiling point at standard barometric pressure; chemical purity; moisture content; chloride ions content; specific aqueous conductance; acid number; and residue content.
SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:
1.1.1 Type I electronic or ultra-clean grade,
1.1.2 Type II standard or vapor-degreasing grade, and
1.1.3 Type II A general purpose, packaged in a pressurized container grade.

SCOPE
1.1 This specification establishes the requirements for three grades of trichlorotrifluoroethane solvent:
1.1.1 Type I electronic or ultra-clean grade,
1.1.2 Type II standard or vapor-degreasing grade, and
1.1.3 Type IIA general purpose, packaged in a pressurized container grade.  Note-Practices D3884 and D4276 and STPs 310A and 403A provide additional important information on labeling, vapor-degreasing and solvent properties.

SCOPE
1.1 This specification covers technical grade methylene chloride. Note-See Practices D3844 and D4276 and STP403A  for additional important information on solvent handling and solvent properties.

SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best fit cleaning agent and process. This guide takes into account environmental pollution prevention factors in a selection process.
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the cleaning material selection process, calling for engineers to customize their selection based on the cleaning requirements for the cleaning tasks at hand. If a part can be cleaned, and kept clean, it can be cycled through several process steps that have cleaning requirements. This eliminates extra cleaning process steps during the total process. A total life cycle cost analysis or performance/cost of ownership study is recommended to compare the methods available.
1.3 This guide is for general industry manufacturing, equipment maintenance and remanufacturing operations, and to some extent precision cleaning of mechanical parts and assemblies. It is not intended to be used for optical, medical, or electronics applications, nor is it intended for dry-cleaning or super-critical fluid cleaning.