ISO/TC 2/SC 13 - Fasteners with non-metric thread

This document specifies the mechanical and physical properties of heat treated tapping screws made of steel, with thread sizes ST2,2 to ST9,5 in accordance with ISO 1478, when tested at the ambient temperature range of 10 °C to 35 °C, and the related test methods. Tapping screws are designed to form mating threads in sheet metals, without their own threads being deformed. Tapping screws are not intended to be pretensioned by design, even though they can experience varying degrees of low-level tensile stress after installation.

This document specifies the characteristics of hexagon washer head tapping screws, made of steel and stainless steel, with thread sizes ST2,2 to ST8, and with product grade A.

This document specifies the characteristics of hexagon washer head drilling screws with tapping screw threads, made of steel, with thread sizes ST2,9 to ST6,3, and with product grade A.

This International Standard specifies hexagon flange head tapping screws with threads from ST2,2 up to and
including ST9,5.

ISO 1483:2011 specifies the characteristics of slotted raised countersunk (oval) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 1482:2011 specifies the characteristics of slotted countersunk (flat) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 7050:2011 specifies the characteristics of cross-recessed countersunk (flat) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 1481:2011 specifies the characteristics of slotted pan head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 7049:2011 specifies the characteristics of cross-recessed pan head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 1479:2011 specifies the characteristics of hexagon head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 7051:2011 specifies the characteristics of cross-recessed raised countersunk (oval) head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive.

ISO 10510:2011 specifies the requirements for tapping screws and plain washer assemblies with spaced threads from ST2,2 to ST9,5 inclusive, flat seating heads and mechanical properties as specified in ISO 2702.

ISO 14587:2011 specifies the characteristics of hexalobular socket raised countersunk (oval) head tapping screws with thread sizes from ST2,9 to ST6,3 inclusive. If, in special cases, specifications other than those listed in ISO 14587:2011 are required, they can be selected from existing International Standards, for example ISO 1478, ISO 2702, ISO 4759-1.

ISO 14585:2011 specifies the characteristics of hexalobular socket pan head tapping screws with thread sizes from ST2,9 to ST6,3 inclusive. If, in special cases, specifications other than those listed in ISO 14585:2011 are required, they can be selected from existing International Standards, for example ISO 1478, ISO 2702, ISO 4759-1.

ISO 14586:2011 specifies the characteristics of hexalobular socket countersunk head tapping screws with thread sizes from ST2,9 to ST6,3 inclusive. If, in special cases, specifications other than those listed in ISO 14586:2011 are required, they can be selected from existing International Standards, for example ISO 1478, ISO 2702, ISO 4759-1.

Defines the type H and type Z; dimensions are illustrated by figures; tabulates gauge dimensions from No. 0 up to and including No. 4; includes a method of penetration gauging for both types.

ISO 7053:2011 specifies hexagon washer head tapping screws with thread sizes from ST 2,2 to ST 8 inclusive.

ISO 2702:2011 specifies the characteristics of heat-treated steel tapping screws, with tapping screw thread from ST2,2 to ST9,5 inclusive according to ISO 1478, together with the corresponding test methods.

Specifies the characteristics (dimensions, mass, designation) of screws with thread from ST2,2 up to and including ST8.

Specifies the characteristics (dimensions, designation) of screws with thread from ST2,2 up to and including ST9,5 as well as check on head and flange gauges A and B.

Specifies the characteristics of screws with threads from ST2,2 to ST8. Describes the test methods to be used. Figure 1 shows a torsional test apparatus.

Specifies the characteristics of products with thread sizes form ST 2,2 up to and including ST 9,5; includes specifications with reference to International Standards; gives an exaple for the designation.

Specifies the characteristics of products with thread sizes form ST 2,2 up to and including ST 9,5; includes specifications with reference to International Standards; gives an example for the designation

Specifies the characteristics of screws with thread sizes from ST 2,2 up to and including ST 9,5; includes specifications with reference to International Standards; gives an example for the designation.

Specifies the characteristics of screws with thread sizes from ST 2,2 up to and including ST 9,5; includes specifications with reference to international Standards; gives an example for the designation.

Specifies the characteristics of screws with thread sizes from ST 2,2 up to and including ST 9,5; includes specifications with reference to International Standards; gives an example for the designation.

Specifies the characteristics of screws with thread sizes from ST 2,2, up to and including ST 9,5; includes specifications with reference to International Standards; gives an example for the designation.

Specifies the characteristics of types C, F, H and Z with thread sizes form ST 2,2 up to and including ST 9,5; includes specifications with reference to International Standards; gives an example for the designation