SIST EN ISO 23553-1:2014
(Main)Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2014)
Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2014)
EN ISO 23553-1 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil. It applies to automatic and semi-automatic valves which are: - normally closed; - used in combustion plants to interrupt the oil flow with or without delay on closing; - for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without gasoline.
Sicherheits-, Regel- und Steuereinrichtungen für Ölbrenner und Öl verbrennende Geräte - Spezielle Anforderungen - Teil 1: Absperreinrichtungen für Ölbrenner (ISO 23553-1:2014)
Dieser Teil der ISO 23553 legt die Anforderungen an Sicherheit, Konstruktion und Leistung sowie die Prüfung von automatischen und halbautomatischen Ventilen für Öl fest.
Er gilt für automatische und halbautomatische Ventile, die:
als Schnellschlusseinrichtungen ausgelegt sind;
in Verbrennungsanlagen eingesetzt werden, um den Öldurchfluss mit oder ohne Verzögerung des Schließvorgangs sowie mit oder ohne Verzögerung des Öffnungsvorgangs zu unterbrechen;
für den Einsatz mit Ölsorten ohne Benzin (z. B. Diesel, Rohöl, Schweröl oder Kerosin) vorgesehen sind;
ANMERKUNG 1 Für weitere Ölsorten (z. B. Ölemulsionen) können zwischen Hersteller und Prüfstelle zusätzliche Prüfverfahren vereinbart werden.
ANMERKUNG 2 Ölsorten aus Raffinerieprozessen sind klassifiziert als ISO-F-D nach ISO 8216-99 und bilden einen Teil einer Einrichtung mit (einer) anderen Funktion(en) z. B. Ölpumpen. In diesem Fall gelten die Prüfverfahren für diejenigen Bauteile oder Komponenten der Einrichtung, die die automatischen und halbautomatischen Ventile bilden, d. h. die Bauteile, die für die Schließfunktion erforderlich sind;
für die Anwendung an Brennern oder in Geräten vorgesehen sind, die Öl nutzen;
direkt oder indirekt elektrisch oder durch mechanische oder hydraulische Hilfsmittel betrieben werden;
mit Anzeigen für die Geschlossenstellung ausgestattet sind oder nicht.
Dieser Teil der ISO 23553 behandelt nur die Typprüfung.
Dispositifs de commande et de sécurité pour brûleurs à fioul et pour appareils à fioul - Exigences particulières - Partie 1: Dispositifs de coupure pour brûleurs à fioul (ISO 23553-1:2014)
L'ISO 23553-1:2014 spécifie les exigences relatives à la sécurité, à la conception et aux performances ainsi que les essais applicables aux robinets automatiques et semi-automatiques destinés à des appareils à combustible liquide.
Elle s'applique aux robinets automatiques et semi-automatiques qui sont:
-normalement fermés;
-utilisés dans des installations de combustion dans le but d'interrompre l'écoulement du combustible liquide avec ou sans retard sur la fermeture;
-conçus pour être utilisés avec des types de combustible liquide (par exemple, fioul de distillat moyen, pétrole brut, fioul lourd ou kérosène) sans essence;
-conçus pour être utilisés sur des brûleurs ou des appareils à combustible liquide;
-actionnés directement ou indirectement par un moyen électrique, mécanique ou hydraulique;
-équipés ou non de commutateurs à indicateurs de position fermée.
L'ISO 23553-1:2014 couvre uniquement les essais de type.
Varnostne in nadzorne naprave za oljne gorilnike in aparate na olje - Posebne zahteve - 1. del: Varnostno zaporne naprave za oljne gorilnike (ISO 23553-1:2014)
Standard EN ISO 23553-1 opredeljuje varnostne zahteve, konstrukcijske zahteve in zahteve glede zmogljivosti ter metode za preskušanje avtomatskih in polavtomatskih ventilov za nafto. Velja za avtomatske in polavtomatske ventile za nafto, ki: - so običajno zaprti, - se uporabljajo v kurilnih napravah za prekinitev dotoka nafte z ali brez zakasnjenega zapiranja; - se uporabljajo z vrstami olja brez bencina (npr. srednje destilatno kurilno olje, surova nafta, težko olje ali kerozin).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 23553-1:2014
01-julij-2014
1DGRPHãþD
SIST EN ISO 23553-1:2009
Varnostne in nadzorne naprave za oljne gorilnike in aparate na olje - Posebne
zahteve - 1. del: Varnostno zaporne naprave za oljne gorilnike (ISO 23553-1:2014)
Safety and control devices for oil burners and oil-burning appliances - Particular
requirements - Part 1: Shut-off devices for oil burners (ISO 23553-1:2014)
Sicherheits-, Regel- und Steuereinrichtungen für Ölbrenner und Öl verbrennende Geräte
- Spezielle Anforderungen - Teil 1: Absperreinrichtungen für Ölbrenner (ISO 23553-
1:2014)
Dispositifs de commande et de sécurité pour brûleurs à fioul et pour appareils à fioul -
Exigences particulières - Partie 1: Dispositifs de coupure pour brûleurs à fioul (ISO
23553-1:2014)
Ta slovenski standard je istoveten z: EN ISO 23553-1:2014
ICS:
27.060.10 *RULOQLNLQDWHNRþHLQWUGR Liquid and solid fuel burners
JRULYR
SIST EN ISO 23553-1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 23553-1:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 23553-1:2014
EUROPEAN STANDARD
EN ISO 23553-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2014
ICS 27.060.10 Supersedes EN ISO 23553-1:2009
English Version
Safety and control devices for oil burners and oil-burning
appliances - Particular requirements - Part 1: Automatic and
semi-automatic valves (ISO 23553-1:2014)
Dispositifs de commande et de sécurité pour brûleurs à Sicherheits-, Regel- und Steuereinrichtungen für Ölbrenner
combustible liquide et pour appareils à combustible liquide - und Öl verbrennende Geräte - Spezielle Anforderungen -
Exigences particulières - Partie 1: Robinets automatiques et Teil 1: Automatische und halbautomatische Ventile (ISO
semi-automatiques (ISO 23553-1:2014) 23553-1:2014)
This European Standard was approved by CEN on 9 April 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23553-1:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 23553-1:2014
EN ISO 23553-1:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 23553-1:2014
EN ISO 23553-1:2014 (E)
Foreword
This document (EN ISO 23553-1:2014) has been prepared by Technical Committee ISO/TC 161 “Control and
protective devices for gas and/or oil burners and appliances” in collaboration with Technical Committee
CEN/TC 47 “Atomizing oil burners and their components - Function - Safety - Testing” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2014, and conflicting national standards shall be withdrawn
at the latest by November 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 23553-1:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 23553-1:2014 has been approved by CEN as EN ISO 23553-1:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 23553-1:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 23553-1:2014
INTERNATIONAL ISO
STANDARD 23553-1
Second edition
2014-05-15
Safety and control devices for oil
burners and oil-burning appliances —
Particular requirements —
Part 1:
Automatic and semi-automatic valves
Dispositifs de commande et de sécurité pour brûleurs à combustible
liquide et pour appareils à combustible liquide — Exigences
particulières —
Partie 1: Robinets automatiques et semi-automatiques
Reference number
ISO 23553-1:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 4
4 Classification . 6
4.1 Classes of control . 6
4.2 Groups of control . 6
5 Test conditions . 6
6 Construction . 7
6.1 General . 7
6.2 Construction requirements . 7
6.3 Materials . 9
6.4 Oil connections.10
6.101 Welded connections .12
6.102 Indicator .12
7 Performance .12
7.1 General .12
7.2 Leak-tightness.12
7.3 Torsion and bending .14
7.4 Rated flow rate .15
7.5 Durability .15
7.6 Functional requirements .16
7.7 Endurance .17
8 EMC/Electrical requirements .18
8.1 Protection against environmental influences .18
8.2 Variations in supply voltage .19
8.3 Short-term voltage interruptions and drops .19
8.4 Variations in supply frequency .19
8.5 Surge immunity test .19
8.6 Electrical fast transient/burst .19
8.7 Immunity to conducted disturbances .19
8.8 Immunity to radiated fields .19
8.9 Electrostatic discharge immunity test .19
8.10 Test for immunity to power-frequency magnetic field .19
8.11 Electrical equipment .19
8.101 Electrical components .22
8.102 Ring wave .23
9 Marking, installation and operating instructions .24
9.1 Marking .24
9.2 Installation and operating instructions .24
9.3 Warning notice .25
Annex A (informative) Leak-tightness test — Volumetric method .26
Annex B (informative) Leak-tightness test — Pressure-loss method .27
Annex C (normative) Conversion of pressure loss into leakage rate .28
Annex D (normative) Test for immunity to power-frequency magnetic fields.29
Annex E (normative) Specific regional requirements in European countries .30
Annex F (normative) Specific regional requirements in Canada and USA .32
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
Annex G (normative) Specific regional requirements in Japan .35
Bibliography .36
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 161, Control and protective devices for gas and/or
oil burners and appliances.
This second edition cancels and replaces the first edition (ISO 23553-1:2007), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 23553-1:2007/Cor1:2009).
ISO 23553 consists of the following parts, under the general title Safety and control devices for oil burners
and oil-burning appliances — Particular requirements:
— Part 1: Automatic and semi-automatic valves.
It should be noted that the following significant technical changes compared to the previous edition
have been incorporated in this part of ISO 23553:
a) change of the title from shut-off valves to automatic and semi-automatic valves;
b) extension of the scope to automatic and semi-automatic valves;
c) introduction of further classifications for valves;
d) inclusion of references to the general electrical requirements of IEC 60730-1:2010;
e) integration of non electrical requirements from IEC 60730-2-19;
f) integration of electrical requirements from IEC 60730-2-19 which are unalterable for valves;
g) inclusion of the subclause 7.7.103 “Test of endurance of electrically operated valves”;
h) change of endurance cycles for valves up to DN 15;
i) extended limits of internal leakage for valves ≤ DN 50;
j) test of closing function updated.
© ISO 2014 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
Introduction
This part of ISO 23553 is designed to be used in combination with ISO 23550. This part together with
ISO 23550 establishes the full requirements as they apply to the product covered by this part of ISO 23553.
This part of ISO 23553 adapts ISO 23550, where needed, by stating “with the following modification”,
“with the following addition”, “is replaced by the following” or “is not applicable,” in the corresponding
clause.
In order to identify specific requirements that are particular to this part of ISO 23553, that are not
already covered by ISO 23550, this document may contain clauses or subclauses that are additional to
the structure of ISO 23550. These clauses are numbered starting from 101 or, in the case of an Annex,
are designated AA, BB, CC etc.
In an attempt to develop a fully International Standard, it has been necessary to take into consideration
the differing requirements resulting from practical experience and installation practices in various
regions of the world and to recognize the variation in basic infrastructure associated with oil controls
and appliances, some of which are addressed in Annexes E, F and G. This part of ISO 23553 intends to
provide a basic framework of requirements that recognizes these differences.
vi © ISO 2014 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 23553-1:2014
INTERNATIONAL STANDARD ISO 23553-1:2014(E)
Safety and control devices for oil burners and oil-burning
appliances — Particular requirements —
Part 1:
Automatic and semi-automatic valves
IMPORTANT — When reference is made in this part of — ISO 23553 to ISO 23550, the word “gas”
shall be replaced by “oil” as appropriate. The current base standard, ISO 23550:2011, focuses on
gas controls only. It is, however, the intention to revise the base standard in such a fashion that
both, gas and oil product standards can be used in conjunction with the base standard. Attention
is drawn especially to the following subclauses: 6.4, 7.4 and 7.5.
1 Scope
This part of ISO 23553 specifies safety, constructional and performance requirements and testing of
automatic and semi-automatic valves for oil.
It applies to automatic and semi-automatic valves which are:
— normally closed;
— used in combustion plants to interrupt the oil flow with or without delay on closing;
— for use with oil types (e.g. middle distillate fuel oil, crude oil, heavy fuel oil or kerosene) without
gasoline;
NOTE 1 For other oil types (e.g. oil emulsions), additional test methods can be agreed between the manufacturer
and the test authority.
NOTE 2 Oil types from petroleum refining processes are classified ISO-F-D in ISO 8216-99 and form part
of a device having other function(s), such as oil pumps. In this case the test methods apply to those parts or
components of the device forming the automatic and semi-automatic valves, i.e. those parts which are necessary
for the closing function;
— for use on burners or in appliances using oil;
— directly or indirectly operated, electrically or by mechanical or hydraulic means;
— fitted with or without closed-position indicator switches.
This part of ISO 23553 covers type testing only.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 272, Fasteners — Hexagon products — Widths across flats
ISO 1179-1, Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 1: Threaded ports
© ISO 2014 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
ISO 1179-2, Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 2: Heavy-duty (S series) and light-duty (L series) stud ends
with elastomeric sealing (type E)
ISO 1179-3, Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 3: Light-duty (L series) stud ends with sealing by O-ring with
retaining ring (types G and H)
ISO 1179-4, Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 4: Stud ends for general use only with metal-to-metal sealing
(type B)
ISO 3601-5, Fluid power systems — O-rings — Part 5: Specification of elastomeric materials for industrial
applications
ISO 6149-1, Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261
metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal
ISO 6149-3, Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261
metric threads and O-ring sealing — Part 3: Dimensions, design, test methods and requirements for light-
duty (L series) stud ends
ISO/TR 7620, Rubber materials — Chemical resistance
ISO 8216-99, Petroleum products — Fuels (class F) — Classification — Part 99: General
ISO 8434-1, Metallic tube connections for fluid power and general use — Part 1: 24 degree cone connectors
ISO 8434-2, Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors
ISO 8434-3, Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors
ISO 8434-6, Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors
with or without O-ring
ISO 9974-1, Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with
elastomeric or metal-to-metal sealing — Part 1: Threaded ports
ISO 9974-3, Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with
elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B)
ISO 23550:2011, Safety and control devices for gas burners and gas-burning appliances — General
requirements
ISO 23553, Safety and control devices for oil burners and oil-burning appliances — Particular requirements
ISO 23936-1, Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact
with media related to oil and gas production — Part 1: Thermoplastics
ISO 23936-2, Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact
with media related to oil and gas production — Part 2: Elastomers
IEC 60534-1, Industrial-process control valves — Part 1: Control valve terminology and general considerations
IEC 60534-2-3, Industrial-process control valves — Part 2-3: Flow capacity; test procedures
IEC 60730-1:2010, Automatic electrical controls for household and similar use — Part 1: General
requirements
EN 1057, Copper and copper alloys — Seamless, round copper tubes for water and gas in sanitary and
heating applications
2 © ISO 2014 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 23553-1:2014
ISO 23553-1:2014(E)
EN 1092-1, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 1: Steel flanges
EN 1092-2, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 2: Cast iron flanges
EN 1092-3, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories PN
designated — Part 3: Copper alloy flanges
EN 1092-4, Flanges and their joints — Circular flanges for pipes, valves, fittings and accessories, PN
designated — Part 4: Aluminium alloy flanges
EN 1254-1, Copper and copper alloys — Plumbing fittings — Part 1: Fittings with ends for capillary soldering
or capillary brazing to copper tubes
EN 1254-2, Copper and copper alloys — Plumbing fittings — Part 2: Fittings with compression ends for use
with copper tubes
EN 1254-3, Copper and copper alloys — Plumbing fittings — Part 3: Fittings with compression ends for use
with plastics pipes
EN 1254-5, Copper and copper alloys — Plumbing fittings — Part 5: Fittings with short ends for capillary
brazing to copper tubes
EN 10226-1, Pipe threads where pressure tight joints are made on the threads — Part 1: Taper external
threads and parallel internal threads; Dimensions, tolerances and designation
EN 10226-2, Pipe threads where pressure tight joints are made on the threads — Part 2: Taper external
threads and taper internal threads - Dimensions, tolerances and designation
EN 10241, Steel threaded pipe fittings
EN 10242, Threaded pipe fitting in malleable cast iron
EN 10284, Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems
EN 10305-1, Steel tubes for precision applications — Technical delivery conditions — Part 1: Seamless cold
drawn tubes
EN 10305-2, Steel tubes for precision applications — Technical delivery conditions — Part 2: Welded cold
drawn tubes
EN 10305-3, Steel tubes for precision applications — Technical delivery conditions — Part 3: Welded cold
sized tubes
EN 10305-4, Steel tubes for precision applications — Technical delivery conditions — Part 4: Seamless cold
drawn tubes for hydraulic and pneumatic power systems
EN 10305-6, Steel tubes for precision applications — Technical delivery conditions — Part 6: Welded cold
drawn tubes for hydraulic and pneumatic power systems
EN 12516 (all parts), Industrial valves — Shell design strength
EN 12627, Industrial valves — Butt welding ends for steels valves
EN 12760, Valves — Socket welding ends for steel valves
prEN 10344,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.