ASTM D2949-22
(Specification)Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, deflection load, crush resistance, flattening resistance, impact resistance, and solvent cement. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded.
Note 1: This specification was formerly issued under the title, 3-in. Thin Wall Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings.
1.1.1 Techniques for making solvent-cement joints are given in Practice D2855.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D2949 −22 An American National Standard
Standard Specification for
3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic
1
Drain, Waste, and Vent Pipe and Fittings
This standard is issued under the fixed designation D2949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers requirements and test methods
D618Practice for Conditioning Plastics for Testing
formaterials,dimensionsandtolerances,deflectionload,crush
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
resistance, flattening resistance, impact resistance, and solvent
tics
cement.Aformofmarkingisalsoincluded.Plasticwhichdoes
D1784Classification System and Basis for Specification for
not meet the material requirements specified in Section 5 is
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
excluded.
rinated Poly(Vinyl Chloride) (CPVC) Compounds
NOTE 1—This specification was formerly issued under the title, 3-in.
D2122Test Method for Determining Dimensions of Ther-
ThinWallPoly(VinylChloride)(PVC)PlasticDrain,Waste,andVentPipe
moplastic Pipe and Fittings
and Fittings.
D2152Test Method for Adequacy of Fusion of Extruded
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
1.1.1 Techniques for making solvent-cement joints are
Acetone Immersion
given in Practice D2855.
D2412Test Method for Determination of External Loading
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
Characteristics of Plastic Pipe by Parallel-Plate Loading
and appendixes which provide explanatory material. These
D2444Practice for Determination of the Impact Resistance
notesandfootnotes(excludingthoseintablesandfigures)shall
of Thermoplastic Pipe and Fittings by Means of a Tup
not be considered as requirements of the specification.
(Falling Weight)
D2564Specification for Solvent Cements for Poly(Vinyl
1.3 The values stated in inch-pound units are to be regarded
Chloride) (PVC) Plastic Piping Systems
as standard. The values given in parentheses are mathematical
D2855Practice for the Two-Step (Primer and Solvent Ce-
conversions to SI units that are provided for information only
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
and are not considered standard.
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
1.4 The following precautionary caveat pertains only to the
Piping Components with Tapered Sockets
test methods portion, Section 7, of this specification: This
D3311Specification for Drain, Waste, and Vent (DWV)
standard does not purport to address all of the safety concerns,
Plastic Fittings Patterns
if any, associated with its use. It is the responsibility of the user
F402 Practice for Safe Handling of Solvent Cements,
of this standard to establish appropriate safety, health, and
Primers, and Cleaners Used for Joining Thermoplastic
environmental practices and determine the applicability of
Pipe and Fittings
regulatory limitations prior to use.
F412Terminology Relating to Plastic Piping Systems
F1498SpecificationforTaperPipeThreads60°forThermo-
1.5 This international standard was developed in accor-
plastic Pipe and Fittings
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3. Terminology
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3.1 Definitions—Definitions are in accordance with Termi-
Barriers to Trade (TBT) Committee.
nology F412, and abbreviations are in accordance with Termi-
nology D1600, unless otherwise specified.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Oct. 1, 2022. Published October 2022. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1971. Last previous edition approved in 2018 as D2949–18. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D2949-22. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2949−22
4. Significance and Use 6.2.2.3 Transition Adapters
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2949 − 18 D2949 − 22 An American National Standard
Standard Specification for
3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic
1
Drain, Waste, and Vent Pipe and Fittings
This standard is issued under the fixed designation D2949; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, deflection load, crush
resistance, flattening resistance, impact resistance, and solvent cement. A form of marking is also included. Plastic which does not
meet the material requirements specified in Section 5 is excluded.
NOTE 1—This specification was formerly issued under the title, 3-in. Thin Wall Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and
Fittings.
1.1.1 Techniques for making solvent-cement joints are given in Practice D2855.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Nov. 1, 2018Oct. 1, 2022. Published January 2019October 2022. Originally approved in 1971. Last previous edition approved in 20102018 as
D2949 – 10.D2949 – 18. DOI: 10.1520/D2949-18.10.1520/D2949-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2949 − 22
D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone
Immersion
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2855 Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated
Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1498 Specification for Taper Pipe Threads 60° for Ther
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.