ASTM C877M-16
(Specification)Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections (Metric)
Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections (Metric)
ABSTRACT
This specification deals with the metric standard for three types of external sealing bands to be used in conjunction with concrete pipe, manholes, and precast box sections. The first type of bands shall be composed of rubber, mastic, and protective film elements, while the second type shall consist of a plastic film, reinforced, rubberized, asphalt, mastic coating with steel straps. The third type shall be composed of a backing band, an applied continuous butyl adhesive coating and an optional release element. All the elements of each type of sealing band shall have physical properties conforming with specified limits as determined through appropriate test methods herein provided.
SCOPE
1.1 This specification covers external sealing bands to be used in conjunction with concrete pipe as defined in Terminology C822 and conforming to Specifications C14M, C76M, C412M, C478M, C506M, C507M, C655M, C985M, C1417M, and C1433M.
1.1.1 Type I, Rubber and Mastic Bands.
1.1.2 Type II, Plastic Film and Mesh Reinforced Mastic Bands.
1.1.3 Type III, Chemically Bonded Adhesive Butyl Bands.
1.2 This specification is the metric counterpart of Specification C877.
Note 1: This specification covers only the design and material of the sealing bands. Sealing bands covered by this specification are adequate, when properly installed, for external hydrostatic pressures up to 90 kPa, (9.14 m) without leakage. The amount of infiltration or exfiltration flow in an installed pipeline is dependent upon many factors other than the sealing bands; allowable quantities and suitable testing of the installed pipeline and system must be covered by other specifications.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C877M −16
Standard Specification for
External Sealing Bands for Concrete Pipe, Manholes, and
1
Precast Box Sections (Metric)
This standard is issued under the fixed designation C877M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope crete Manhole Sections (Metric)
C506M Specification for Reinforced ConcreteArch Culvert,
1.1 This specification covers external sealing bands to be
Storm Drain, and Sewer Pipe (Metric)
used in conjunction with concrete pipe as defined in Terminol-
C507M Specification for Reinforced Concrete Elliptical
ogy C822 and conforming to Specifications C14M, C76M,
Culvert, Storm Drain, and Sewer Pipe (Metric)
C412M, C478M, C506M, C507M, C655M, C985M, C1417M,
C655M Specification for Reinforced Concrete D-Load
and C1433M.
Culvert, Storm Drain, and Sewer Pipe (Metric)
1.1.1 Type I, Rubber and Mastic Bands.
C681 Test Method for Volatility of Oil- and Resin-Based,
1.1.2 Type II, Plastic Film and Mesh Reinforced Mastic
Knife-Grade, Channel Glazing Compounds
Bands.
C822 Terminology Relating to Concrete Pipe and Related
1.1.3 Type III, Chemically Bonded Adhesive Butyl Bands.
Products
1.2 This specification is the metric counterpart of Specifi-
C985M Specification for Nonreinforced Concrete Specified
cation C877.
Strength Culvert, Storm Drain, and Sewer Pipe (Metric)
NOTE 1—This specification covers only the design and material of the
C1417M Specification for Manufacture of Reinforced Con-
sealing bands. Sealing bands covered by this specification are adequate,
crete Sewer, Storm Drain, and Culvert Pipe for Direct
when properly installed, for external hydrostatic pressures up to 90 kPa,
Design (Metric)
(9.14 m) without leakage.The amount of infiltration or exfiltration flow in
C1433M Specification for Precast Reinforced Concrete
aninstalledpipelineisdependentuponmanyfactorsotherthanthesealing
bands; allowable quantities and suitable testing of the installed pipeline
Monolithic Box Sections for Culverts, Storm Drains, and
and system must be covered by other specifications.
Sewers (Metric)
D36 Test Method for Softening Point of Bitumen (Ring-and-
2. Referenced Documents
Ball Apparatus)
2
2.1 ASTM Standards:
D217 Test Methods for Cone Penetration of Lubricating
A167 Specification for Stainless and Heat-Resisting
Grease
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
D395 Test Methods for Rubber Property—Compression Set
3
drawn 2014)
D412 Test Methods forVulcanized Rubber andThermoplas-
C14M Specification for Nonreinforced Concrete Sewer,
tic Elastomers—Tension
Storm Drain, and Culvert Pipe (Metric)
D471 Test Method for Rubber Property—Effect of Liquids
C76M Specification for Reinforced Concrete Culvert, Storm
D570 Test Method for Water Absorption of Plastics
Drain, and Sewer Pipe (Metric)
D573 Test Method for Rubber—Deterioration in an Air
C412M Specification for Concrete Drain Tile (Metric)
Oven
C478M Specification for Circular Precast Reinforced Con-
D624 Test Method for Tear Strength of Conventional Vul-
canized Rubber and Thermoplastic Elastomers
D882 Test Method for Tensile Properties of Thin Plastic
1
This specification is under the jurisdiction of ASTM Committee C13 on
Sheeting
Concrete Pipe and is the direct responsibility of Subcommittee C13.08 on Joints for
D903 Test Method for Peel or Stripping Strength of Adhe-
Precast Concrete Structures.
Current edition approved Dec. 15, 2016. Published January 2017. Originally
sive Bonds
approved in 1980. Last previous edition approved in 2009 as C877M – 02 (2009).
D1171 Test Method for Rubber Deterioration—Surface
DOI: 10.1520/C0877M-16.
2 Ozone Cracking Outdoors (Triangular Specimens)
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D1278 Test Methods for Rubber from Natural Sources—
Standards volume information, refer to the standard’s Document Summary page on
Chemical Analysis
the ASTM website.
3
D1682 Test Method for Breaking Load and Elongation of
The last approved version of this historical standard is referenced on
3
www.astm.org. Textile Fabric (Withdrawn 1992)
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C877M−16
TABLE 1 Required Sealing Band Width
D1963 Test Method for Specific Gravity of Drying Oils,
Varnishes, Resins, and Related Materials at 25/25°C Equivalent Circular Pipe Sealing Band
3
Diameter, mm Width, mm
(Withdrawn 2004)
450 to 825 180
D2202 Test Method for Slump of Sealants
900 to 1950 230
D2240 Te
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C877M − 02 (Reapproved 2009) C877M − 16
Standard Specification for
External Sealing Bands for Concrete Pipe, Manholes, and
1
Precast Box Sections (Metric)
This standard is issued under the fixed designation C877M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers external sealing bands to be used in conjunction with concrete pipe as defined in Terminology
C822 and conforming to Specifications C14M, C76M, C412M, C478M, C506M, C507M, C655M, C985M, C1417M, and
C1433M.
1.1.1 Type I, Rubber and Mastic Bands.
1.1.2 Type II, Plastic Film and Mesh Reinforced Mastic Bands.
1.1.3 Type III, Chemically Bonded Adhesive Butyl Bands.
1.2 This specification is the metric counterpart of Specification C877.
NOTE 1—This specification covers only the design and material of the sealing bands. Sealing bands covered by this specification are adequate, when
properly installed, for external hydrostatic pressures up to 90 kPa, (9.14 m) without leakage. The amount of infiltration or exfiltration flow in an installed
pipeline is dependent upon many factors other than the sealing bands; allowable quantities and suitable testing of the installed pipeline and system must
be covered by other specifications.
2. Referenced Documents
2
2.1 ASTM Standards:
3
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
C14M Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)
C76M Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)
C412M Specification for Concrete Drain Tile (Metric)
C478M Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric)
C506M Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)
C507M Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
C655M Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)
C681 Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds
3
C766 Test Method for Adhesion After Impact of Preformed Tape Sealants (Withdrawn 1994)
C822 Terminology Relating to Concrete Pipe and Related Products
C985M Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric)
C1417M Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
C1433M Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers
(Metric)
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D217 Test Methods for Cone Penetration of Lubricating Grease
D395 Test Methods for Rubber Property—Compression Set
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D471 Test Method for Rubber Property—Effect of Liquids
D570 Test Method for Water Absorption of Plastics
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.08 on Joints for Precast
Concrete Structures.
Current edition approved Oct. 1, 2009Dec. 15, 2016. Published October 2009January 2017. Originally approved in 1980. Last previous edition approved in 20022009 as
ε1
C877M – 02 (2009). . DOI: 10.1520/C0877M-02R09.10.1520/C0877M-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C877M − 16
D573 Test Method for Rubber—Deterioration in an Air Oven
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
D1171 Test Method for Rubber Deterioration—Surface Ozone Cracking Outdoors (Triangular Specimens)
D1278
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.