23.040.80 - Seals for pipe and hose assemblies
ICS 23.040.80 Details
Seals for pipe and hose assemblies
Dichtungen fur Rohr- und Schlauchverbindungen
Joints d'étanchéité pour tuyauterie et flexibles
Tesnila za cevne zveze
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 23.040.80 - Seals for pipe and hose assemblies
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies requirements and associated test methods for rubber materials used in gas installations, gas equipment and gas appliances in contact with 1st, 2nd and 3rd family combustible gases as classified in EN 437:2018, additionally LPG, bio methane and bio LPG, in the same quality, are covered. It also establishes a classification based on temperature range and hardness. This document is applicable to materials from which homogeneous seals and homogeneous or reinforced diaphragms are manufactured.
Since the dimensions and shape of the components differ from those of standard test pieces taken from sheet material as used for type testing of the rubber materials according to this document, tolerances have been made in the requirements specified by Annex A for the components with respect to those specified for standard test pieces.
The range of operating temperatures covered by this document is –40 °C to +150 °C.
For applications with potential condensation, this document is not applicable for silicon rubber, e.g. above 200 hPa (200 mbar) nominal pressure or at temperatures below 0 °C with 3rd family gases.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and associated test methods for rubber materials used in gas installations, gas equipment and gas appliances in contact with 1st, 2nd and 3rd family combustible gases as classified in EN 437:2018, additionally LPG, bio methane and bio LPG, in the same quality, are covered. It also establishes a classification based on temperature range and hardness. This document is applicable to materials from which homogeneous seals and homogeneous or reinforced diaphragms are manufactured.
Since the dimensions and shape of the components differ from those of standard test pieces taken from sheet material as used for type testing of the rubber materials according to this document, tolerances have been made in the requirements specified by Annex A for the components with respect to those specified for standard test pieces.
The range of operating temperatures covered by this document is –40 °C to +150 °C.
For applications with potential condensation, this document is not applicable for silicon rubber, e.g. above 200 hPa (200 mbar) nominal pressure or at temperatures below 0 °C with 3rd family gases.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and test methods for unsintered polytetrafluorethylene (PTFE) tapes and polytetrafluorethylene (PTFE) strings (PTFE tapes or PTFE strings, for short) which are suitable for sealing threaded metallic joints as specified in EN 10226-1:2004.
This document covers two classes of PTFE tapes and PTFE strings suitable for fine (F) and coarse (G) threads.
The PTFE tapes and PTFE strings are used as sealing materials for metallic threaded joints in contact with 1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases (LPG)) up to 500 kPa, up to 700 kPa for hot water of heating systems, and up to 20 kPa in gas appliances and their auxiliary equipment. The maximum working pressure covered in this document is 2000 kPa which is relevant to LPG storage. The temperature range is limited to −20 °C to 125 °C.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and test methods for unsintered polytetrafluorethylene (PTFE) tapes and polytetrafluorethylene (PTFE) strings (PTFE tapes or PTFE strings, for short) which are suitable for sealing threaded metallic joints as specified in EN 10226-1:2004.
This document covers two classes of PTFE tapes and PTFE strings suitable for fine (F) and coarse (G) threads.
The PTFE tapes and PTFE strings are used as sealing materials for metallic threaded joints in contact with 1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases (LPG)) up to 500 kPa, up to 700 kPa for hot water of heating systems, and up to 20 kPa in gas appliances and their auxiliary equipment. The maximum working pressure covered in this document is 2000 kPa which is relevant to LPG storage. The temperature range is limited to −20 °C to 125 °C.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and test methods for unsintered polytetrafluorethylene (PTFE)
tapes and polytetrafluorethylene (PTFE) strings (PTFE tapes or PTFE strings, for short) which are
suitable for sealing threaded metallic joints as specified in EN 10226-1:2004.
This document covers two classes of PTFE tapes and PTFE strings suitable for fine (F) and coarse (G)
threads.
The PTFE tapes and PTFE strings are used as sealing materials for metallic threaded joints in contact with
1st family gases (town gas), 2nd family gases (natural gas) and 3rd family gases (liquefied petroleum gases
(LPG)) up to 500 kPa, up to 700 kPa for hot water of heating systems, and up to 20 kPa in gas appliances
and their auxiliary equipment. The maximum working pressure covered in this document is 2000 kPa
which is relevant to LPG storage. The temperature range is limited to −20 °C to 125 °C.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the gasket parameters required by EN 1591-1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of other shapes and dimensions.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2 Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the quality assurance procedures that are applicable to ensure that delivered gaskets comply with the relevant product standards. This document sets down procedures by which a user can have confidence that the salient features of each batch of gaskets or gasket materials delivered to them will be constant.
The gasket types covered by this document are those that are within the scope of the EN 1514 series and EN 12560 series and are simultaneously within the scope of the EN 1591 series. An exception is those gaskets intended solely for domestic fluids (like water, waste water ...) which are based on rubber with or without reinforcement like fillers and/or inserts.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the quality assurance procedures that are applicable to ensure that delivered gaskets comply with the relevant product standards. This document sets down procedures by which a user can have confidence that the salient features of each batch of gaskets or gasket materials delivered to him will be constant.
The gasket types covered by this document are those that are within the scope of the series of standards
EN 1514 and EN 12560 and are simultaneously within the scope of the series of standards EN 1591. An exception is those gaskets intended solely for domestic fluids (like water, waste water ...) which are based on rubber with or without reinforcement like fillers and/or inserts.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092 4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8.
NOTE 2 Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the gasket parameters required by EN 1591 1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of other shapes and dimensions.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a test method for determining the leaktightness of elastomeric sealing ring
type joints for buried thermoplastics non-pressure piping systems.
Unless otherwise specified in the referring standard, the tests are carried out at the following basic test
pressures:
— p1: internal negative air pressure (partial vacuum);
— p2: a low internal hydrostatic pressure;
— p3: a higher internal hydrostatic pressure.
It also describes the following four test conditions under which the tests are performed:
a) Condition A: without any additional diametric or angular deflection;
b) Condition B: with diametric deflection;
c) Condition C: with angular deflection;
d) Condition D: with simultaneous angular and diametric deflection.
The applicable selection of the test pressure(s) and the test condition(s) is/are specified in the referring
standard.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the characteristics of configuration, dimensions, tolerances and mass for
moulded O-Ring seal elements, phosphate ester fluid resistant, for straight thread tube fitting boss for use as
static seals in hydraulic systems for aerospace application.
Application temperature range: −55 °C to 107 °C of continuous operation.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations:
- Class 150, to Class 1 500 for nominal sizes DN 15 to DN 600, and
- Class designation 2 500 up to and including DN 300.
The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting.
The dimensions of spiral wound gaskets for tongue and groove flange facing types and spigot and recess flange facing types to EN 1759-1 are not included in this standard.
Such gaskets may be available, however, for these types of flange and the purchaser is advised to consult the manufacturer as to their availability. Similarly, for slip-on or screwed flange types, the manufacturer should be consulted about availability.
NOTE Dimensions of other types of gasket for use with flanges complying with the requirements of EN 1759-1 are given in EN 12560-1, EN 12560-3, EN 12560-4 and EN 12560-5, EN 12560-6 and EN 12560-7.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations: - Class 150, to Class 1 500 for nominal sizes DN 15 to DN 600, and - Class designation 2 500 up to and including DN 300. The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting. The dimensions of spiral wound gaskets for tongue and groove flange facing types and spigot and recess flange facing types to EN 1759-1 are not included in this standard. Such gaskets may be available, however, for these types of flange and the purchaser is advised to consult the manufacturer as to their availability. Similarly, for slip-on or screwed flange types, the manufacturer should be consulted about availability.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard applies to all types of surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. This includes components such as valves, filters, regulators, transducers, and controllers. The scope of this standard is limited as follows. a) This standard addresses only surface-mount fluid distribution components and proper sealing methods. This standard is limited to sealing methods using elastomeric material for the seals. b) The designs of the actual system components and the flow substrate are not specified in this standard. Any indication of mounting direction or other indexing is left to the manufacturer as required for its equipment. c) Users shall be aware that, on the basis of the stream conditions of their processes, other technologies and components may be readily available. d) This standard does not address the effects of various stream conditions on the technical functionality of the component. e) This standard does not address maintenance concerns for the components. f) This standard does not refer to design issues pertaining to specific safety requirements. These issues should be referenced to other standards, organizations, and recommended guidelines. g) International, national, and local codes, regulations, and laws should be consulted to ensure that each component meets the user's regulatory requirements. The object of this standard is to establish properties and physical dimensions that define the interface for surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. The interface controls the dimensions and location of the sealing surfaces to allow change of just one element of the system without modification of the entire system. This is what makes the system modular from both a design and a maintenance standpoint.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62339-1:2006 establishes properties and physical dimensions that define the interface for surface-mount fluid distribution components with elastomeric sealing devices used within process analyser and sample-handling systems. The interface controls the dimensions and location of the sealing surfaces to allow change of just one element of the system without modification of the entire system. This is what makes the system modular from both a design and a maintenance standpoint. It cancels and replaces IEC/PAS 62339-1 published in 2003. This first edition constitutes a technical revision.
- Standard8 pagesEnglish languagesale 15% off
- Standard17 pagesEnglish and French languagesale 15% off
This draft European Standard specifies a method for determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the dimensions of polymeric O-Ring gaskets for use with grooved flanges complying with EN 1092 for PN 10, PN 16, PN 25, PN 40.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092 1, EN 1092 2, EN 1092 3 and EN 1092 4 are given in EN 1514 1, EN 1514 2, EN 1514 3, EN 1514 4, EN 1514-6 and EN 1514-7
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the dimensions of polymeric O-Ring gaskets for use with grooved flanges complying with EN 1092 for PN 10, PN 16, PN 25, PN 40.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092 1, EN 1092 2, EN 1092 3 and EN 1092 4 are given in EN 1514 1, EN 1514 2, EN 1514 3, EN 1514 4, EN 1514-6 and EN 1514-7
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with prEN 1759 1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and including NPS 12.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to prEN 1759 1, EN 1759 3 and EN 1759 4 are given in EN 12560 1, EN 12560 2, EN 12560 3, EN 12560 4, EN 12560 5 and EN 12560 6.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with EN 1092-1 for PN 2,5, PN 6, PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 900.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, EN 1514-6 and prEN 1514-8.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with EN 1092-1 for PN 2,5, PN 6, PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 900.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, EN 1514-6 and prEN 1514-8.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal jacketed gaskets for use with flanges complying with prEN 1759 1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and including NPS 12.
This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to prEN 1759 1, EN 1759 3 and EN 1759 4 are given in EN 12560 1, EN 12560 2, EN 12560 3, EN 12560 4, EN 12560 5 and EN 12560 6.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal gaskets for use with flanges complying with prEN 1759-1 for Class 150, Class 300, Class 600, Class 900, Class 1500 and Class 2500 up to and including NPS 24.
This document does not extend to serrated covered metal based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down can be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to prEN 1759-1, prEN 1759-3 and prEN 1759-4 are given in EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560- 5 and prEN 12560-7.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal gaskets for use with flanges complying with EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 3000.
This document does not extend to covered serrated metal based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down can be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, prEN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, prEN 1514-7 and prEN 1514-8.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal gaskets for use with flanges complying with prEN 1759-1 for Class 150, Class 300, Class 600, Class 900, Class 1500 and Class 2500 up to and including NPS 24.
This document does not extend to serrated covered metal based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down can be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to prEN 1759-1, prEN 1759-3 and prEN 1759-4 are given in EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560- 5 and prEN 12560-7.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the construction, dimensions and marking of covered serrated metal gaskets for use with flanges complying with EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 up to and including DN 3000.
This document does not extend to covered serrated metal based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down can be applied to them.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, prEN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-2, EN 1514-3, EN 1514-4, prEN 1514-7 and prEN 1514-8.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Modification of elongation percentage in Table 5
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Created at the request of A. Ganesh (CC/010319)
* (2 Nov 2000) DOW=DAV+21 months (CEN/BT C 149/2000) - pls contact Ashok Ganesh to check before DAV
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
TC - Modification of elongation percentage in Table 5
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the dimensions, types, design, materials and marking requirements of IBC (inside bolt circle) non-metallic PTFE envelope gaskets for use with flanges complying with EN 1759-1, EN 1759-3, EN 1759-4 for Class designation 150 and 300 for sizes up to and including NPS 24 (DN600).
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the dimensions, types, design and marking requirements of corrugated, flat or grooved metallic filled metallic gaskets for use in conjunction with flanges complying with EN 1759-1 for Class designations 150, 300, 600, 900 and 1500 for sizes up to and including NPS 24 (DN600), and for Class designation 2500 for nominal size designations up to and including NPS 12 (DN300).
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the dimensions, types, design, materials and marking requirements of non-metallic flat gaskets with or without inserts, for use with flanges complying with EN 1759-1, EN 1759-3 and EN 1759-4, for Class designations 150, 300, 600 and 900 for sizes up to and including NPS 24 (DN600).
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day