ASTM A625/A625M-13(2018)
(Specification)Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
ABSTRACT
This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. The black plates shall be produced with ground roll and shot-blasted roll finishes and shall be furnished oiled or dry.
SCOPE
1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.
1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed edge.
1.3 This specification is applicable to orders in either inch-pound units (as A625), which is supplied in thicknesses from 135-lb base weight (0.0149 in.) and lighter, or SI units (as A625M), which is supplied in thicknesses from 0.378 mm and lighter.
1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A625/A625M −13 (Reapproved 2018)
Standard Specification for
Tin Mill Products, Black Plate, Single-Reduced
This standard is issued under the fixed designationA625/A625M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope A623M Specification for Tin Mill Products, General Re-
quirements [Metric]
1.1 This specification covers single-reduced black plate
produced from low carbon, cold-reduced steel, furnished in
3. Ordering Information
coils and cut sizes, for use in the manufacture of containers,
closures, signs, toys and other products, as well as for plating 3.1 Orders for product under this specification shall include
applications.
the following information, as required and applicable, to
adequately describe the desired materials.
1.2 It may be supplied dry or oiled and with or without
3.1.1 Name of product (single-reduced black plate).
surface treatment. This product is normally supplied with a
3.1.2 Surface appearance and finish (Section 4).
trimmed edge.
3.1.2.1 Dry.
1.3 This specification is applicable to orders in either
3.1.2.2 Oiled (type of oil; mineral or suitable for lithograph-
inch-pound units (as A625), which is supplied in thicknesses
ing) (Section 5).
from 135-lb base weight (0.0149 in.) and lighter, or SI units (as
3.1.2.3 Chemically treated and oiled (see Specification
A625M), which is supplied in thicknesses from 0.378 mm and
A623 or Specification A623M).
lighter.
3.1.3 Thickness (see Specification A623 or Specification
1.4 The values stated in either inch-pound or SI units are to A623M).
be regarded as standard.Within the text, the SI units are shown
3.1.4 Width.
in brackets. The values stated in each system are not exact 3.1.5 Length, for cut sizes only.
equivalents; therefore, each system must be used indepen-
3.1.6 Rolling direction must be specified by underlining the
dently of the other. Combining values from the two systems steel (rolling width) for cut sizes.
may result in nonconformance with this specification.
3.1.7 Steel type (see Specification A623 or Specification
A623M).
1.5 This international standard was developed in accor-
3.1.8 Mechanical designation requirements (see Specifica-
dance with internationally recognized principles on standard-
tion A623 or Specification A623M).
ization established in the Decision on Principles for the
3.1.9 Intended application.
Development of International Standards, Guides and Recom-
3.1.10 Quantity, in base boxes [SITAs] (see Note 5).
mendations issued by the World Trade Organization Technical
3.1.11 On coils, specify minimum of range or acceptable
Barriers to Trade (TBT) Committee.
inside diameters. The standard inside diameter is approxi-
mately 16 in. if ordered to Specification A625 [410 mm if
2. Referenced Documents
2 ordered to Specification A625M]. Coils should be specified to
2.1 ASTM Standards:
a maximum coil weight if ordered to SpecificationA625 [mass
A623 Specification for Tin Mill Products, General Require-
if ordered to Specification A625M] or maximum outside
ments
diameter, or both.
3.1.12 Packaging.
3.1.13 ASTM specification designation and year of issue.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3.1.14 Special requirements, where applicable.
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
A01.20 on Tin Mill Products.
NOTE1—Atypicalorderingdescriptionisasfollows:1000BaseBoxes,
Current edition approved Sept. 1, 2018. Published September 2018. Originally
Single-Reduced Black Plate, oiled, 80 lb base weight, 30 in. by coil, MR,
approved in 1968. Last previous edition approved in 2013 as A625/A625M –13.
T5CA for lithographed can bodies to ASTM A625/A625M - XX. [600
DOI: 10.1520/A0625_A0625M-13R18.
2 SITAs,Single-ReducedBlackPlate,oiled,0.25mm,810mmbycoil,MR,
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
T5CA for lithographed can bodies to Specification A625/A625M.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on NOTE 2—A typical ordering description for cut sizes is as follows: 500
the ASTM w
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A625/A625M − 13 (Reapproved 2018)
Standard Specification for
Tin Mill Products, Black Plate, Single-Reduced
This standard is issued under the fixed designation A625/A625M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope A623M Specification for Tin Mill Products, General Re-
quirements [Metric]
1.1 This specification covers single-reduced black plate
produced from low carbon, cold-reduced steel, furnished in
3. Ordering Information
coils and cut sizes, for use in the manufacture of containers,
closures, signs, toys and other products, as well as for plating
3.1 Orders for product under this specification shall include
applications. the following information, as required and applicable, to
adequately describe the desired materials.
1.2 It may be supplied dry or oiled and with or without
3.1.1 Name of product (single-reduced black plate).
surface treatment. This product is normally supplied with a
3.1.2 Surface appearance and finish (Section 4).
trimmed edge.
3.1.2.1 Dry.
1.3 This specification is applicable to orders in either
3.1.2.2 Oiled (type of oil; mineral or suitable for lithograph-
inch-pound units (as A625), which is supplied in thicknesses
ing) (Section 5).
from 135-lb base weight (0.0149 in.) and lighter, or SI units (as
3.1.2.3 Chemically treated and oiled (see Specification
A625M), which is supplied in thicknesses from 0.378 mm and
A623 or Specification A623M).
lighter.
3.1.3 Thickness (see Specification A623 or Specification
1.4 The values stated in either inch-pound or SI units are to
A623M).
be regarded as standard. Within the text, the SI units are shown 3.1.4 Width.
in brackets. The values stated in each system are not exact
3.1.5 Length, for cut sizes only.
equivalents; therefore, each system must be used indepen-
3.1.6 Rolling direction must be specified by underlining the
dently of the other. Combining values from the two systems
steel (rolling width) for cut sizes.
may result in nonconformance with this specification.
3.1.7 Steel type (see Specification A623 or Specification
A623M).
1.5 This international standard was developed in accor-
3.1.8 Mechanical designation requirements (see Specifica-
dance with internationally recognized principles on standard-
tion A623 or Specification A623M).
ization established in the Decision on Principles for the
3.1.9 Intended application.
Development of International Standards, Guides and Recom-
3.1.10 Quantity, in base boxes [SITAs] (see Note 5).
mendations issued by the World Trade Organization Technical
3.1.11 On coils, specify minimum of range or acceptable
Barriers to Trade (TBT) Committee.
inside diameters. The standard inside diameter is approxi-
2. Referenced Documents mately 16 in. if ordered to Specification A625 [410 mm if
ordered to Specification A625M]. Coils should be specified to
2.1 ASTM Standards:
a maximum coil weight if ordered to Specification A625 [mass
A623 Specification for Tin Mill Products, General Require-
if ordered to Specification A625M] or maximum outside
ments
diameter, or both.
3.1.12 Packaging.
3.1.13 ASTM specification designation and year of issue.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3.1.14 Special requirements, where applicable.
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
A01.20 on Tin Mill Products.
NOTE 1—A typical ordering description is as follows: 1000 Base Boxes,
Current edition approved Sept. 1, 2018. Published September 2018. Originally
Single-Reduced Black Plate, oiled, 80 lb base weight, 30 in. by coil, MR,
approved in 1968. Last previous edition approved in 2013 as A625/A625M –13.
T5CA for lithographed can bodies to ASTM A625/A625M - XX. [600
DOI: 10.1520/A0625_A0625M-13R18.
SITAs, Single-Reduced Black Plate, oiled, 0.25 mm, 810 mm by coil, MR,
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
T5CA for lithographed can bodies to Specification A625/A625M.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
NOTE 2—A typical ordering description for cut sizes is as follows: 500
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Base Boxes, Single Reduced Black Plate, oiled, 80 lb base weight MR, T-2
Copyright
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A625/A625M − 13 A625/A625M − 13 (Reapproved 2018)
Standard Specification for
Tin Mill Products, Black Plate, Single-Reduced
This standard is issued under the fixed designation A625/A625M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and
cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.
1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed
edge.
1.3 This specification is applicable to orders in either inch-pound units (as A625), which is supplied in thicknesses from 135-lb
base weight (0.0149 in.) and lighter, or SI units (as A625M), which is supplied in thicknesses from 0.378 mm and lighter.
1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
A623 Specification for Tin Mill Products, General Requirements
A623M Specification for Tin Mill Products, General Requirements [Metric]
3. Ordering Information
3.1 Orders for product under this specification shall include the following information, as required and applicable, to adequately
describe the desired materials.
3.1.1 Name of product (single-reduced black plate).
3.1.2 Surface appearance and finish (Section 4).
3.1.2.1 Dry.
3.1.2.2 Oiled (type of oil; mineral or suitable for lithographing) (Section 5).
3.1.2.3 Chemically treated and oiled (see Specification A623 or Specification A623M).
3.1.3 Thickness (see Specification A623 or Specification A623M).
3.1.4 Width.
3.1.5 Length, for cut sizes only.
3.1.6 Rolling direction must be specified by underlining the steel (rolling width) for cut sizes.
3.1.7 Steel type (see Specification A623 or Specification A623M).
3.1.8 Mechanical designation requirements (see Specification A623 or Specification A623M).
3.1.9 Intended application.
3.1.10 Quantity, in base boxes [SITAs] (see Note 5).
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.20
on Tin Mill Products.
Current edition approved Oct. 1, 2013Sept. 1, 2018. Published October 2013September 2018. Originally approved in 1968. Last previous edition approved in 20082013
as A625/A625M – 08.A625/A625M –13. DOI: 10.1520/A0625_A0625M-13.10.1520/A0625_A0625M-13R18.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
A625/A625M − 13 (2018)
3.1.11 On coils, specify minimum of range or acceptable inside diameters. The standard inside diameter is approximately 16
in. if ordered to Specification A625 [410 mm if ordered to Specification A625M]. Coils should be specified to a maximum coil
weight if ordered to Specification A625 [mass if ordered to Specification A625M] or maximum outside diameter, or both.
3.1.12 Packaging.
3.1.13 ASTM specification designation and year of issue.
3.1.14 Special requirements, where applicable.
NOTE 1—A typical ordering description is as follows: 1000 Base Boxes, Single-Reduced Black Plate, oiled, 80 lb base we
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.