iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E1530-04

(Test Method)

Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique

Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique

SCOPE
1.1 This test method covers a steady-state technique for the determination of the resistance to thermal transmission (thermal resistance) of materials in thicknesses of less than 25 mm. For homogeneous opaque solid specimens of a representative thickness, thermal conductivity can be determined (see Note 0). This test method is useful for specimens having a thermal resistance in the range from 10 to 400 104 m2K/W, which can be obtained from materials of thermal conductivity in the approximate range from 0.1 to 30 W/(mK) over the approximate temperature range from 150 to 600 K. It can be used outside these ranges with reduced accuracy for thicker specimens and for thermal conductivity values up to 60 W/(mK).Note 0
A body is considered homogeneous when the property to be measured is found to be independent of specimen dimensions.
1.2 This test method is similar in concept to Test Method C 518, but is modified to accommodate smaller test specimens, having a higher thermal conductance. In addition, significant attention has been paid to ensure that the thermal resistance of contacting surfaces is minimized and reproducible.
1.3 The values stated in SI units are considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2004
ICS
17.200.10 - Heat. Calorimetry
Technical Committee
E37 - Thermal Measurements
Drafting Committee
E37.05 - Thermophysical Properties
Current Stage
Ref Project

Relations

Replaces
ASTM E1530-99 - Standard Test Method for Evaluating the Resistance to Thermal Transmission of Thin Specimens of Materials by the Guarded Heat Flow Meter Technique
Effective Date
01-May-2004
Replaced By
ASTM E1530-06 - Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
Effective Date
01-Sep-2006
Referred By
ASTM D5144-08(2021) - Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
Effective Date
01-May-2004
Referred By
ASTM C1470-20 - Standard Guide for Testing the Thermal Properties of Advanced Ceramics
Effective Date
01-May-2004
Referred By
ASTM D8157-19 - Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants
Effective Date
01-May-2004
Referred By
ASTM D8104-17(2023) - Standard Guide for Determining Coating Qualification Test Data Applicability
Effective Date
01-May-2004
Referred By
ASTM D6744-06(2017)e1 - Standard Test Method for Determination of the Thermal Conductivity of Anode Carbons by the Guarded Heat Flow Meter Technique
Effective Date
01-May-2004
Referred By
ASTM F942-18(2023)e1 - Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
Effective Date
01-May-2004

Buy Standard

ASTM E1530-04 - Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter TechniqueASTM E1530-04 - Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
PreviousNext
Standard
ASTM E1530-04 - Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E 1530 – 04
Standard Test Method for
Evaluating the Resistance to Thermal Transmission of
1
Materials by the Guarded Heat Flow Meter Technique
This standard is issued under the fixed designation E1530; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C 1045 Practice for Calculating Thermal Transmission
Properties Under Steady-State Test Conditions
1.1 This test method covers a steady-state technique for the
E220 Method for Calibration of Thermocouples by Com-
determination of the resistance to thermal transmission (ther-
parison Techniques
mal resistance) of materials in thicknesses of less than 25 mm.
E1142 TerminologyRelatingtoThermophysicalProperties
For homogeneous opaque solid specimens of a representative
E1225 Test Method for Thermal Conductivity of Solids by
thickness, thermal conductivity can be determined (see Note
Means of the Guarded-Comparative-Longitudinal Heat
1). This test method is useful for specimens having a thermal
−4 2
Flow Technique
resistance in the range from 10 to 400 3 10 m ·K/W, which
F104 Classification System for Nonmetallic Gasket Mate-
can be obtained from materials of thermal conductivity in the
rials
approximate range from 0.1 to 30 W/(m·K) over the approxi-
F433 Practice for Evaluating Thermal Conductivity of
mate temperature range from 150 to 600 K. It can be used
Gasket Materials
outside these ranges with reduced accuracy for thicker speci-
mens and for thermal conductivity values up to 60 W/(m·K).
3. Terminology
NOTE 1—A body is considered homogeneous when the property to be
3.1 Definitions of Terms Specific to This Standard:
measured is found to be independent of specimen dimensions.
3.1.1 heatfluxtransducer(HFT)—adevicethatproducesan
1.2 This test method is similar in concept to Test Method
electrical output that is a function of the heat flux, in a
C518,butismodifiedtoaccommodatesmallertestspecimens,
predefined and reproducible manner.
having a higher thermal conductance. In addition, significant
3.1.2 thermal conductance (C)—the time rate of heat flux
attention has been paid to ensure that the thermal resistance of
through a unit area of a body induced by unit temperature
contacting surfaces is minimized and reproducible.
difference between the body surfaces.
1.3 The values stated in SI units are considered standard.
3.1.2.1 average temperature of a surface—the area-
1.4 This standard does not purport to address all of the
weighted mean temperature of that surface.
safety concerns, if any, associated with its use. It is the
3.1.2.2 average (mean) temperature of a specimen (disc
responsibility of the user of this standard to establish appro-
shaped)—themeanvalueoftheupperandlowerfacetempera-
priate safety and health practices and determine the applica-
tures.
bility of regulatory limitations prior to use.
3.1.3 thermal conductivity (l)—(of a solid material)—the
time rate of heat flow, under steady conditions, through unit
2. Related Documents
area,perunittemperaturegradientinthedirectionperpendicu-
2
2.1 ASTM Standards:
lar to the area:
C518 Test Method for Steady-State Heat Flux Measure-
3.1.3.1 apparent thermal conductivity—When other modes
ments and Thermal Transmission Properties by Means of
of heat transfer through a material are present in addition to
the Heat Flow Meter Apparatus
conduction, the results of the measurements performed in
accordance with this test method will represent the apparent or
effective thermal conductivity for the material tested.
1
ThistestmethodisunderthejurisdictionofASTMCommitteeE37onThermal
3.1.4 thermal resistance (R)—the reciprocal of thermal
Measurements and is the direct responsibility of Subcommittee E37.05 onThermo-
conductance.
physical Properties.
3.2 Symbols:
Current edition approved May 1, 2004. Published June 2004. Originally
approved in 1993. Last previous edition approved in 1999 as E1530–99.
3.2.1 l—thermal conductivity, W/(m·K) or Btu·in./
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 2
(h·ft ·°F).
contact ASTM Customer service at service@astm.org. For Annual Book of ASTM
2 2
3.2.2 C—thermal conductance, W/m( ·K) or Btu/(h·ft ·°F).
Standards volume information, refer to the standard’s Document Summary page on
2 2
the ASTM website. 3.2.3 R—thermal resistance, m ·K/W or h·ft ·°F/Btu.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E1530–04
3.2.4 Dx—specimen thickness, mm or in. together with the electrical output of the HFT. This output
2 2
3.2.5 A—
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E473-23b(Terminology)
Standard Terminology Relating to Thermal Analysis and Rheology

SCOPE
1.1 This terminology is a compilation of definitions of terms used in ASTM documents relating to thermal analysis and rheology. This terminology includes only those terms for which ASTM either has standards or is contemplating some action. It is not intended to be an all-inclusive listing of terms related to thermal analysis and rheology.  
1.2 This terminology specifically supports the single-word form for terms using thermo as a prefix, such as thermoanalytical or thermomagnetometry, while recognizing that for some terms a two-word form can be used, such as thermal analysis. This terminology does not support, nor does it recommend, use of the grammatically incorrect, single-word form using thermal as a prefix, such as, thermalanalytical or thermalmagnetometry.  
1.3 A definition is a single sentence with additional information included in a Discussion area. It is reviewed every five years.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2070-23(Test Method)
Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods

SIGNIFICANCE AND USE
6.1 These test methods are useful for research and development, quality assurance, regulatory compliance, and specification acceptance purposes.  
6.2 The determination of the order of a chemical reaction or transformation at specific temperatures or time conditions is beyond the scope of these test methods.  
6.3 The activation energy results obtained by these test methods may be compared with those obtained from Test Method E698 for nth order and accelerating reactions. Activation energy, pre-exponential factor, and reaction order results by these test methods may be compared to those for Test Method E2041 for nth order reactions.
SCOPE
1.1 Test Methods A, B, and C determine kinetic parameters for activation energy, pre-exponential factor and reaction order using differential scanning calorimetry (DSC) from a series of isothermal experiments over a small (≈10 K) temperature range. Test Method A is applicable to low nth order reactions. Test Methods B and C are applicable to accelerating reactions such as thermoset curing or pyrotechnic reactions and crystallization transformations in the temperature range from 300 K to 900 K (nominally 30 °C to 630 °C). These test methods are applicable only to these types of exothermic reactions when the thermal curves do not exhibit shoulders, double peaks, discontinuities or shifts in baseline.  
1.2 Test Methods D and E also determines the activation energy of a set of time-to-event and isothermal temperature data generated by this or other procedures  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM E1142-23b(Terminology)
Standard Terminology Relating to Thermophysical Properties

SCOPE
1.1 This is a compilation of only those terms and corresponding definitions included in or being considered for inclusion in ASTM documents relating to thermophysical properties. It is not intended as an all-inclusive listing of thermophysical property terms. Terms that are generally understood or defined adequately in other readily available sources are not included.  
1.2 A definition is a single sentence with additional information included in a Discussion.  
1.3 Definitions of terms specific to a particular field (such as dynamic mechanical measurements) are identified with an italicized introductory phrase.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E1356-23(Test Method)
Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Differential scanning calorimetry provides a rapid test method for determining changes in specific heat capacity in a homogeneous material. The glass transition is manifested as a step change in specific heat capacity. For amorphous and semicrystalline materials the determination of the glass transition temperature may lead to important information about their thermal history, processing conditions, stability, progress of chemical reactions, and mechanical and electrical behavior.  
5.2 This test method is useful for research, quality control, and specification acceptance.
SCOPE
1.1 This test method covers the assignment of the glass transition temperatures of materials using differential scanning calorimetry or differential thermal analysis.  
1.2 This test method is applicable to amorphous materials or to partially crystalline materials containing amorphous regions, that are stable and do not undergo decomposition or sublimation in the glass transition region.  
1.3 The normal operating temperature range is from −120 °C to 500 °C. The temperature range may be extended, depending upon the instrumentation used.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 ISO standards 11357–2 is equivalent to this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2603-15(2023)(Practice)
Standard Practice for Calibration of Fixed-Cell Differential Scanning Calorimeters

SIGNIFICANCE AND USE
5.1 Fixed-cell differential scanning calorimeters are used to determine the transition temperatures and energetics of materials in solution. For this information to be accepted with confidence in an absolute sense, temperature and heat calibration of the apparatus or comparison of the resulting data to that of known standard materials is required.  
5.2 This practice is useful in calibrating the temperature and heat flow axes of fixed-cell differential scanning calorimeters.
SCOPE
1.1 This practice covers the calibration of fixed-cell differential scanning calorimeters over the temperature range from –10 °C to +120 °C.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2041-23(Test Method)
Standard Test Method for Estimating Kinetic Parameters by Differential Scanning Calorimeter Using the Borchardt and Daniels Method

SIGNIFICANCE AND USE
6.1 This test method is useful in research and development.  
6.2 The determination of the appropriate model for a chemical reaction or transformation and the values associated with its kinetic parameters may be used in the estimation of reaction performance at temperatures or time conditions not easily tested. This use, however, is not described in this test method.
SCOPE
1.1 This test method describes the determination of the kinetic parameters of activation energy, Arrhenius pre-exponential factor, and reaction order using the Borchardt and Daniels2 treatment of data obtained by differential scanning calorimetry. This test method is applicable to the temperature range from 170 K to 870 K (−100 °C to 600°C).  
1.2 This treatment is applicable only to smooth exothermic reactions with no shoulders, discontinuous changes, or shifts in baseline. It is applicable only to reactions with reaction order n ≤ 2. It is not applicable to acceleratory reactions and, therefore, is not applicable to the determination of kinetic parameters for most thermoset curing reactions or to crystallization reactions.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1952-23(Test Method)
Standard Test Method for Thermal Conductivity and Thermal Diffusivity by Modulated Temperature Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Thermal conductivity is a useful design parameter for the rate of heat transfer through a material.  
5.2 The results of this test method may be used for design purposes, service evaluation, manufacturing control, research and development, and hazard evaluation. (See Practice E1231.)
SCOPE
1.1 This test method describes the determination of thermal conductivity of homogeneous, non-porous solid materials in the range of 0.10 W/(K·m) to 1.0 W/(K·m) by modulated temperature differential scanning calorimeter. This range includes many polymeric, glass, and ceramic materials. Thermal diffusivity, which is related to thermal conductivity through specific heat capacity and density, may also be derived. Thermal conductivity and diffusivity can be determined at one or more temperatures over the range of 0 °C to 90 °C.  
1.2 The values stated in SI units are to be regarded as standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E1970-23(Practice)
Standard Practice for Statistical Treatment of Thermoanalytical Data

SIGNIFICANCE AND USE
5.1 The standard deviation, or one of its derivatives, such as relative standard deviation or pooled standard deviation, derived from this practice, provides an estimate of precision in a measured value. Such results are ordinarily expressed as the mean value ± the standard deviation, that is, X ± s.  
5.2 If the measured values are, in the statistical sense, “normally” distributed about their mean, then the meaning of the standard deviation is that there is a 67 % chance, that is 2 in 3, that a given value will lie within the range of ± one standard deviation of the mean value. Similarly, there is a 95 % chance, that is 19 in 20, that a given value will lie within the range of ± two standard deviations of the mean. The two standard deviation range is sometimes used as a test for outlying measurements.  
5.3 The calculation of precision in the slope and intercept of a line, derived from experimental data, commonly is required in the determination of kinetic parameters, vapor pressure or enthalpy of vaporization. This practice describes how to obtain these and other statistically derived values associated with measurements by thermal analysis.
SCOPE
1.1 This practice details the statistical data treatment used in some thermal analysis methods.  
1.2 The method describes the commonly encountered statistical tools of the mean, standard derivation, relative standard deviation, pooled standard deviation, pooled relative standard deviation, the best fit to a (linear regression of a) straight line (or plane), and propagation of uncertainties for all calculations encountered in thermal analysis methods (see Practice E2586).  
1.3 Some thermal analysis methods derive the analytical value from the slope or intercept of a linear regression straight line (or plane) assigned to three or more sets of data pairs. Such methods may require an estimation of the precision in the determined slope or intercept. The determination of this precision is not a common statistical tool. This practice details the process for obtaining such information about precision.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2009-23(Test Method)
Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Oxidation onset temperature is a relative measure of the degree of oxidative stability of the material evaluated at a given heating rate and oxidative environment (e.g., oxygen); the higher the OOT value the more stable the material. The OOT is described in Fig. 1. The OOT values can be used for comparative purposes and are not an absolute measurement, like the oxidation induction time (OIT) at a constant temperature (see Test Method E1858). The presence or effectiveness of antioxidants may be determined by these test methods.
FIG. 1 DSC Oxidation (Extrapolated) Onset Temperature (OOT)  
5.2 Typical uses of these test methods include the oxidative stability of edible oils and fats (oxidative rancidity), lubricants, greases, and polyolefins.
SCOPE
1.1 These test methods describe the determination of the oxidative properties of hydrocarbons by differential scanning calorimetry or pressure differential scanning calorimetry under linear heating rate conditions and are applicable to hydrocarbons, which oxidize exothermically in their analyzed form.  
1.2 Test Method A—A differential scanning calorimeter (DSC) is used at ambient pressure of one atmosphere of oxygen.  
1.3 Test Method B—A pressure DSC (PDSC) is used at high pressure (e.g., 3.5 MPa (500 psig) of oxygen).  
1.4 Test Method C—A differential scanning calorimeter (DSC) is used at ambient pressure of one atmosphere of air.  
1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E2716-23(Test Method)
Standard Test Method for Determining Specific Heat Capacity by Modulated Temperature Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Modulated temperature differential scanning calorimetric measurements provide a rapid, simple method for determining specific heat capacities of materials, even under quasi-isothermal conditions.  
5.2 Specific heat capacities are important for design purposes, quality control, and research and development.  
5.3 The use of a stepped quasi-isothermal program may be used to follow structure changes in materials.
SCOPE
1.1 This test method describes the determination of specific heat capacity by modulated temperature differential scanning calorimetry. For the determination of specific heat capacity by a step-isothermal or multiple step-isothermal temperature program, the reader is referred to Test Method E1269.  
1.2 This test method is generally applicable to thermally stable solids and liquids.  
1.3 The normal operating range of the test is from (–100 to 600) °C. The temperature range may be extended depending upon the instrumentation and specimen holders used.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off