ASTM F30-96(2017)

Standard Specification for Iron-Nickel Sealing Alloys

ABSTRACT
This specification covers the characteristics and requirements for iron-nickel alloys intended primarily for sealing to glass in electronic applications. The alloys shall conform to chemical composition, surface finish, temper, grain size, and thermal expansion requirements as stated herein.
SCOPE
1.1 This specification covers iron-nickel alloys that are intended primarily for sealing to glass in electronic applications.  
Note 1: Some of these alloys may be used for sealing to ceramics, but this specification in its present form is not intended to cover material for metal-to-ceramic seals.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The hazard statement pertains only to the test method sections, Sections 10 and 12.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-May-2017
• ICS: 77.120.40 - Nickel, chromium and their alloys
• Technical Committee: F01 - Electronics
• Drafting Committee: F01.03 - Metallic Materials, Wire Bonding, and Flip Chip

Relations

• Refers: ASTM F144-80(2015) - Standard Practice for Making Reference Glass-Metal Sandwich Seal and Testing for Expansion Characteristics by Polarimetric Methods
• Effective Date: 01-May-2015
• Refers: ASTM E228-11(2016) - Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
• Effective Date: 01-Sep-2016
• Refers: ASTM E18-17 - Standard Test Methods for Rockwell Hardness of Metallic Materials
• Effective Date: 01-Jul-2017
• Refers: ASTM E18-18 - Standard Test Methods for Rockwell Hardness of Metallic Materials
• Effective Date: 01-Jul-2018
• Refers: ASTM F14-80(2015) - Standard Practice for Making and Testing Reference Glass-Metal Bead-Seal
• Effective Date: 01-May-2015
• Referred By: ASTM F85-76(2018) - Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes
• Effective Date: 01-Jun-2017
• Referred By: ASTM F144-80(2019) - Standard Practice for Making Reference Glass-Metal Sandwich Seal and Testing for Expansion Characteristics by Polarimetric Methods
• Effective Date: 01-Jun-2017
• Referred By: ASTM F14-80(2019) - Standard Practice for Making and Testing Reference Glass-Metal Bead-Seal
• Effective Date: 01-Jun-2017
• Referred By: ASTM F140-98(2020) - Standard Practice for Making Reference Glass-Metal Butt Seals and Testing for Expansion Characteristics by Polarimetric Methods
• Effective Date: 01-Jun-2017
• Referred By: ASTM F375-20 - Standard Specification for Integrated Circuit Lead Frame Material
• Effective Date: 01-Jun-2017

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F30 −96 (Reapproved 2017)
Standard Specification for
1
Iron-Nickel Sealing Alloys
ThisstandardisissuedunderthefixeddesignationF30;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F14Practice for Making andTesting Reference Glass-Metal
Bead-Seal
1.1 This specification covers iron-nickel alloys that are
F140Practice for Making Reference Glass-Metal Butt Seals
intended primarily for sealing to glass in electronic applica-
and Testing for Expansion Characteristics by Polarimetric
tions.
Methods
NOTE1—Someofthesealloysmaybeusedforsealingtoceramics,but
F144Practice for Making Reference Glass-Metal Sandwich
this specification in its present form is not intended to cover material for
Seal and Testing for Expansion Characteristics by Polari-
metal-to-ceramic seals.
metric Methods
1.2 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
3. Ordering Information
conversions to SI units that are provided for information only
3.1 Ordersformaterialunderthisspecificationshallinclude
and are not considered standard.
the following information:
1.3 This standard does not purport to address the safety
3.1.1 Size,
concerns, if any, associated with its use. It is the responsibility
3.1.2 Temper (Section 6),
of the user of this standard to establish appropriate safety and
3.1.3 Surface finish (Section 8),
health practices and determine the applicability of regulatory
3.1.4 Marking and packaging (Section 16), and
limitations prior to use. The hazard statement pertains only to
3.1.5 Certification if required.
the test method sections, Sections 10 and 12.
1.4 This international standard was developed in accor-
4. Chemical Composition
dance with internationally recognized principles on standard-
4.1 The material shall conform to the requirements as to
ization established in the Decision on Principles for the
chemical composition prescribed in Table 1.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
5. Surface Lubricants
Barriers to Trade (TBT) Committee.
5.1 All lubricants used in processing shall be thoroughly
removed. Protective coatings present on the material as
2. Referenced Documents
shipped shall be readily removable by any of the common
2
2.1 ASTM Standards:
organic degreasing solvents.
E18Test Methods for Rockwell Hardness of Metallic Ma-
terials
6. Temper
E29Practice for Using Significant Digits in Test Data to
6.1 The desired temper of the material shall be specified on
Determine Conformance with Specifications
the purchase order. Unless otherwise specified, wire, rod, bar,
E112Test Methods for Determining Average Grain Size
and tubing shall be given a final bright anneal by the manu-
E228Test Method for Linear Thermal Expansion of Solid
facturer. Strip and sheet shall be annealed properly to develop
Materials With a Push-Rod Dilatometer
deep drawing properties. For deep drawing the hardness shall
notexceedRockwellB82formaterial0.100in.(2.54mm)and
1 less in thickness, and B85 for material over 0.100 in. thick
This specification is under the jurisdiction of ASTM Committtee F01 on
Electronics and is the direct responsibility of Subcommittee F01.03 on Metallic when determined in accordance with Test Methods E18.
Materials, Wire Bonding, and Flip Chip.
CurrenteditionapprovedJune1,2017PublishedJune2017.Originallyapproved
7. Grain Size
in 1977. Last previous edition approved in 2012 as F30–96 (2012). DOI:
10.1520/F0030-96R17.
7.1 Strip and sheet for deep drawing applications shall have
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
anaveragegrainsizenotlargerthanASTMNo.5(Note2)and
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
no more than 10% of the grains shall be larger than No. 5
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. when measured in accordance with Test Methods E112. For
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F30−96 (2017)
TABLE 1 Chemical Requirements
10. Test for Thermal Expansion
Composition, %
10.1 Determinethethermalexpansioncharacteristicswitha
42 Alloy 46 Alloy 48 Alloy 52 Alloy
precision dilatometer after heating the specimen as follows:
UNS UNS UNS 51 Alloy UNS
10.1.1 Heat the specimen in a hydrog
...