ASTM C136-01

Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates

SCOPE
1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving.
1.2 Some specifications for aggregates which reference this method contain grading requirements including both coarse and fine fractions. Instructions are included for sieve analysis of such aggregates.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information purposes only. Specification E11 designates the size of sieve frames with inch units as standard, but in this test method the frame size is designated in SI units exactly equivalent to the inch units.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Jun-2001
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.20 - Aggregates

Relations

• Replaces: ASTM C136-96a - Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
• Effective Date: 10-Jun-2001
• Replaced By: ASTM C136-04 - Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
• Effective Date: 01-Aug-2004
• Referred By: ASTM C117-17 - Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
• Effective Date: 10-Jun-2001
• Referred By: ASTM D3042-17 - Standard Test Method for Insoluble Residue in Carbonate Aggregates
• Effective Date: 10-Jun-2001
• Referred By: ASTM D8012-18 - Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications
• Effective Date: 10-Jun-2001
• Referred By: ASTM C131/C131M-20 - Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
• Effective Date: 10-Jun-2001
• Referred By: ASTM C802-14(2022) - Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials
• Effective Date: 10-Jun-2001
• Referred By: ASTM D2487-17e1 - Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
• Effective Date: 10-Jun-2001
• Referred By: ASTM D6460-19 - Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Earthen Channels from Stormwater-Induced Erosion
• Effective Date: 10-Jun-2001
• Referred By: ASTM D6913/D6913M-17 - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
• Effective Date: 10-Jun-2001
• Referred By: ASTM F2075-20 - Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
• Effective Date: 10-Jun-2001
• Referred By: ASTM C549-18 - Standard Specification for Perlite Loose Fill Insulation
• Effective Date: 10-Jun-2001
• Referred By: ASTM F2223-19a - Standard Guide for ASTM Standards on Playground Surfacing
• Effective Date: 10-Jun-2001
• Referred By: ASTM D1074-17 - Standard Test Method for Compressive Strength of Asphalt Mixtures
• Effective Date: 10-Jun-2001
• Referred By: ASTM D4469-17 - Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures
• Effective Date: 10-Jun-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 136 – 01
Standard Test Method for
1
Sieve Analysis of Fine and Coarse Aggregates
This standard is issued under the fixed designation C 136; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* AASHTO No. T 27 Sieve Analysis of Fine and Coarse
5
Aggregates
1.1 This test method covers the determination of the particle
size distribution of fine and coarse aggregates by sieving.
3. Terminology
1.2 Some specifications for aggregates which reference this
3.1 Definitions—For definitions of terms used in this stan-
method contain grading requirements including both coarse
dard, refer to Terminology C 125.
and fine fractions. Instructions are included for sieve analysis
of such aggregates.
4. Summary of Test Method
1.3 The values stated in SI units are to be regarded as the
4.1 A sample of dry aggregate of known mass is separated
standard. The values in parentheses are provided for informa-
through a series of sieves of progressively smaller openings for
tion purposes only. Specification E 11 designates the size of
determination of particle size distribution.
sieve frames with inch units as standard, but in this test method
the frame size is designated in SI units exactly equivalent to the
5. Significance and Use
inch units.
5.1 This test method is used primarily to determine the
1.4 This standard does not purport to address all of the
grading of materials proposed for use as aggregates or being
safety concerns, if any, associated with its use. It is the
used as aggregates. The results are used to determine compli-
responsibility of the user of this standard to establish appro-
ance of the particle size distribution with applicable specifica-
priate safety and health practices and determine the applica-
tion requirements and to provide necessary data for control of
bility of regulatory limitations prior to use.
the production of various aggregate products and mixtures
containing aggregates. The data may also be useful in devel-
2. Referenced Documents
oping relationships concerning porosity and packing.
2.1 ASTM Standards:
5.2 Accurate determination of material finer than the 75-μm
C 117 Test Method for Materials Finer Than 75-μm (No.
2 (No. 200) sieve cannot be achieved by use of this method
200) Sieve in Mineral Aggregates by Washing
alone. Test Method C 117 for material finer than 75-μm sieve
C 125 Terminology Relating to Concrete and Concrete Ag-
2 by washing should be employed.
gregates
C 670 Practice for Preparing Precision and Bias Statements
6. Apparatus
2
for Test Methods for Construction Materials
6.1 Balances—Balances or scales used in testing fine and
C 702 Practice for Reducing Field Samples of Aggregate to
coarse aggregate shall have readability and accuracy as fol-
2
Testing Size
lows:
3
D 75 Practice for Sampling Aggregates
6.1.1 For fine aggregate, readable to 0.1 g and accurate to
E 11 Specification for Wire-Cloth and Sieves for Testing
4 0.1 g or 0.1 % of the test load, whichever is greater, at any
Purposes
point within the range of use.
2.2 AASHTO Standard:
6.1.2 For coarse aggregate, or mixtures of fine and coarse
aggregate, readable and accurate to 0.5 g or 0.1 % of the test
load, whichever is greater, at any point within the range of use.
1
6.2 Sieves—The sieve cloth shall be mounted on substantial
This test method is under the jurisdiction of ASTM Committee C09 on
Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee
frames constructed in a manner that will prevent loss of
C09.20 on Normal Weight Aggregates.
material during sieving. The sieve cloth and standard sieve
Current edition approved June 10, 2001. Published August 2001. Originally
published as C 136 – 38 T. Last previous edition C 136 – 96a.
2
Annual Book of ASTM Standards, Vol 04.02.
3 5
Annual Book of ASTM Standards, Vol 04.03. Available from American Association of State Highway and Transportation
4
Annual Book of ASTM Standards, Vol 14.02. Officials, 444 North Capitol St. N.W., Suite 225, Washington, DC 20001.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C136–01
frames shall conform to the requirements of Specification E 11. size or larger is such as to preclude convenient sample
Nonstandard sieve frames shall conform to the requirements of reduction and testing as a unit except with large mechanical
Specification
...