ASTM A656/A656M-12
(Specification)Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
ABSTRACT
This specification covers the three types and four strength grades of high strength low-alloy, hot rolled structural steel plate with improved formability. These steels are normally furnished in the as-rolled condition. For plates produced from coil, and furnished without heat treatment or with stress relieving only, additional testing requirements and the reporting of additional test results, of a reference material shall apply. Chemical composition requirements shall be dependent upon thickness, grade, and intended applications. Tension tests shall be executed to evaluate conformance of specimens with specified mechanical properties requirements.
SCOPE
1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot rolled structural steel plate for use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification offer improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished is as agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.
1.2 The maximum thickness of plates shall be as follows:
Grade Plate Thickness, max,
in. [mm] 502 [50] 601½ [40] 701 [25] 801 [25] 100½[13]
1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. See Appendix X3 of Specification A6/A6M for information on weldability.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A656/A656M −12
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designationA656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers three types and five strength
A6/A6M Specification for General Requirements for Rolled
grades of high-strength low-alloy, hot rolled structural steel
Structural Steel Bars, Plates, Shapes, and Sheet Piling
plate for use in truck frames, brackets, crane booms, rail cars,
and similar applications. Steels that conform to this specifica-
3. General Requirements for Delivery
tion offer improved formability. These steels are normally
3.1 Plates furnished under this specification shall conform
furnished in the as-rolled condition. The type and strength
to the requirements of the current edition of Specification
grade furnished is as agreed upon between the manufacturer
A6/A6M, for the specific plate ordered, unless a conflict exists,
and the purchaser. The types and strength grades are shown in
in which case this specification shall prevail.
the tables.
3.2 Coils are excluded from qualification to this specifica-
1.2 The maximum thickness of plates shall be as follows:
tion until they are processed into finished plates. Plates
Grade Plate Thickness, max, produced from coil means plates that have been cut to
in. [mm]
individual lengths from a coil. The processor directly controls,
50 2 [50]
1 or is responsible for, the operations involved in the processing
60 1 ⁄2 [40]
70 1 [25]
ofacoilintofinishedplates.Suchoperationsincludedecoiling,
80 1 [25]
leveling, cutting to length, testing, inspection, conditioning,
1
100 ⁄2 [13]
heat treatment (if applicable), packaging, marking, loading for
1.3 The values stated in either inch-pound units or SI units
shipment, and certification.
are to be regarded as standard. Within the text, the SI units are
NOTE 1—For plates produced from coil and furnished without heat
shown in brackets. The values stated in each system are not
treatment or with stress relieving only, two test results are to be reported
exact equivalents; therefore, each system must be used inde-
foreachqualifyingcoil.Additionalrequirementsregardingplateproduced
from coil are described in Specification A6/A6M.
pendentlyoftheother.Combiningvaluesfromthetwosystems
may result in nonconformance with this specification. See
4. Materials and Manufacture
Appendix X3 of Specification A6/A6M for information on
4.1 The steel shall be made to fine grain practice.
weldability.
5. Chemical Composition
1.4 For plates produced from coil and furnished without
5.1 Heat analyses shall conform to the chemical require-
heat treatment or with stress relieving only, the additional
requirements,includingadditionaltestingrequirementsandthe ments given in Table 1. Dependent upon thickness, grade, and
intended application, variations in the chemical composition
reporting of additional test results, of Specification A6/A6M
apply. are permitted within the limits given in Table 1 for the
applicable type. Where it is of particular importance, the
manufacturer should be consulted for specific chemical com-
position.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock and Ships. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2012. Published May 2012. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1972. Last previous edition approved in 2011 as A656/A656M – 11. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0656_A0656M-12. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A656/A656M − 12
TABLE 1 Chemical Requirements
NOTE 1—An ellipsis (. . .) indicates that element is not defined for that Type.
Composition, %
Elements
Type 3 Type 7 Type 8
A
Carbon, max 0.18 0.18 0.18
A
Manganese, max 1.65 1.65 1.65
Phosphorus, max 0.025 0.025 0.025
Sulfur, max 0.035 0.035 0.035
Silicon, max 0.60 0.60 0.60
B C
Vanadium, max 0.08 0.15 0.15
Nitrogen, max 0.030 0.030 0.030
B C
Columbium 0.008–0.10 0.10 max 0.10 max
C
T
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A656/A656M–11 Designation: A656/A656M – 12
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designationA656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1This1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot rolled structural steel
plate for use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification
offer improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished
is as agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.
1.2The1.2 The maximum thickness of plates shall be as follows:
Grade Plate Thickness, max,
in. [mm]
50 2 [50]
1
60 1 ⁄2 [40]
70 1 [25]
80 1 [25]
1
100 ⁄2 [13]
1.3 Thevaluesstatedineitherinch-poundunitsorSIunitsaretoberegardedasstandard.Withinthetext,theSIunitsareshown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification. See Appendix X3 of
Specification A6/A6M for information on weldability.
1.4 Forplatesproducedfromcoilandfurnishedwithoutheattreatmentorwithstressrelievingonly,theadditionalrequirements,
including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.02
on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.
Current edition approved Dec.May 1, 2011.2012. Published JanuaryMay 2012. Originally approved in 1972. Last previous edition approved in 20102011 as
A656/A656M – 101. DOI: 10.1520/A0656_A0656M-112.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A656/A656M – 12
2. Referenced Documents
2
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
3. General Requirements for Delivery
3.1 Plates furnished under this specification shall conform to the requirements of the current edition of SpecificationA6/A6M,
for the specific plate ordered, unless a conflict exists, in which case this specification shall prevail.
3.2 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from a coil. The processor directly controls, or is responsible for, the
operations involved in the processing of a coil into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each
qualifying coil. Additional requirements regarding plate produced from coil are described in Specification A6/A6M.
4. Materials and Manufacture
4.1 The steel shall be made to fine grain practice.
5. Chemical Composition
5.1 Heat analyses shall conform to the chemical requirements given in Table 1. Dependent upon thickness, grade, and intended
application, variations in the chemical composition are permitted within the limits given in Table 1 for the applicable type. Where
it is of particular importance, the manufacturer should be consulted for specific chemical composition.
5.2 ProductAnalysis—Ifaproductanalysisismade,itshallconformtotherequirementsgiveninTable1,subjecttotheproduct
analysis tolerances of Specification A6/A6M.
5.3 Where steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or
service will be utilized.
5.4 Unless specifically ordered, the t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A656/A656M − 12 A656/A656M − 12
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designation A656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot rolled structural steel plate for
use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification offer
improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished is as
agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.
1.2 The maximum thickness of plates shall be as follows:
Grade Plate Thickness, max,
in. [mm]
50 2 [50]
1
60 1 ⁄2 [40]
70 1 [25]
80 1 [25]
1
100 ⁄2 [13]
1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification. See Appendix X3 of
Specification A6/A6M for information on weldability.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements,
including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
2. Referenced Documents
2
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
3. General Requirements for Delivery
3.1 Plates furnished under this specification shall conform to the requirements of the current edition of Specification A6/A6M,
for the specific plate ordered, unless a conflict exists, in which case this specification shall prevail.
3.2 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from a coil. The processor directly controls, or is responsible for, the
operations involved in the processing of a coil into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each
qualifying coil. Additional requirements regarding plate produced from coil are described in Specification A6/A6M.
4. Materials and Manufacture
4.1 The steel shall be made to fine grain practice.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.02
on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.
Current edition approved May 1, 2012. Published May 2012. Originally approved in 1972. Last previous edition approved in 2011 as A656/A656M – 11. DOI:
10.1520/A0656_A0656M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A656/A656M − 12
5. Chemical Composition
5.1 Heat analyses shall conform to the chemical requirements given in Table 1. Dependent upon thickness, grade, and intended
application, variations in the chemical composition are permitted within the limits given in Table 1 for the applicable type. Where
it is of particular importance, the manufacturer should be consulted for specific chemical composition.
5.2 Product Analysis—If a product analysis is made, it shall conform to the requirements given in T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.