ASTM D3828-09
(Test Method)Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
SIGNIFICANCE AND USE
Flash point measures the response of the test specimen to heat and ignition source under controlled laboratory conditions. It is only one of a number of properties that must be considered in assessing the overall flammability hazard of a material.
Flash point is used in shipping and safety regulations to define flammable and combustible materials and classify them. Consult the particular regulation involved for precise definitions of these classes.
Flash point can indicate the possible presence of highly volatile and flammable materials in a relatively nonvolatile or nonflammable material.
These test methods use a smaller sample (2 to 4 mL) and a shorter test time (1 to 2 min) than traditional test methods.
Method A, IP 524 and EN ISO 3680 are similar methods for flash no-flash tests. Method B, IP 523 and EN ISO 3679 are similar methods for flash point determination.
SCOPE
1.1 These test methods cover procedures for flash point tests, within the range of –30 to 300°C, of petroleum products and biodiesel liquid fuels, using a small scale closed cup tester. The procedures may be used to determine, whether a product will or will not flash at a specified temperature (flash/no flash Method A) or the flash point of a sample (Method B). When used in conjunction with an electronic thermal flash detector, these test methods are also suitable for flash point tests on biodiesels such as fatty acid methyl esters (FAME).
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.
1.4 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Warning statements appear throughout. See also the Material Safety Data Sheets for the product being tested.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3828 − 09
StandardTest Methods for
1
Flash Point by Small Scale Closed Cup Tester
This standard is issued under the fixed designation D3828; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
INTRODUCTION
These small scale flash point methods are generally used for testing a sample at a specific
temperature where the specimen being tested and the air–vapor mixture above it are close to thermal
equilibrium.TestMethodD3941coversotherflashpointequipmentoperatedataspecifictemperature.
Flash point values are a function of the apparatus design, the condition of the apparatus used, and
the operational procedure carried out. Flash point can therefore only be defined in terms of a standard
test method, and no general valid correlation can be guaranteed between results obtained by different
test methods, or with test apparatus different from that specified.
1. Scope* to heat and flame under controlled laboratory conditions and
should not be used to describe or appraise the fire hazard or
1.1 These test methods cover procedures for flash point
fire risk of materials, products, or assemblies under actual fire
tests, within the range of –30 to 300°C, of petroleum products
conditions. However, results of this test may be used as
and biodiesel liquid fuels, using a small scale closed cup tester.
elements of a fire risk assessment which takes into account all
The procedures may be used to determine, whether a product
of the factors which are pertinent to an assessment of the fire
will or will not flash at a specified temperature (flash/no flash
hazard of a particular end use.
Method A) or the flash point of a sample (Method B). When
1.5 This standard does not purport to address all of the
used in conjunction with an electronic thermal flash detector,
safety concerns, if any, associated with its use. It is the
these test methods are also suitable for flash point tests on
responsibility of the user of this standard to establish appro-
biodiesels such as fatty acid methyl esters (FAME).
priate safety and health practices and determine the applica-
1.2 The values stated in SI units are to be regarded as the
bility of regulatory limitations prior to use.Warningstatements
standard. The values given in parentheses are for information
appearthroughout.SeealsotheMaterialSafetyDataSheetsfor
only.
the product being tested.
1.3 Warning—Mercury has been designated by EPA and
many state agencies as a hazardous material that can cause
2. Referenced Documents
central nervous system, kidney, and liver damage. Mercury, or
2
2.1 ASTM Standards:
its vapor, may be hazardous to health and corrosive to
D3941 Test Method for Flash Point by the Equilibrium
materials.Cautionshouldbetakenwhenhandlingmercuryand
Method With a Closed-Cup Apparatus
mercury-containing products. See the applicable product Ma-
D4057 Practice for Manual Sampling of Petroleum and
terial Safety Data Sheet (MSDS) for details and EPA’s website
Petroleum Products
(http://www.epa.gov/mercury/faq.htm) for additional informa-
D4177 Practice for Automatic Sampling of Petroleum and
tion. Users should be aware that selling mercury or mercury-
Petroleum Products
containingproducts,orboth,inyourstatemaybeprohibitedby
D6299 Practice for Applying Statistical Quality Assurance
state law.
and Control Charting Techniques to Evaluate Analytical
1.4 This standard should be used to measure and describe
Measurement System Performance
the properties of materials, products, or assemblies in response
E300 Practice for Sampling Industrial Chemicals
1
These test methods are under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
2
D02.08 on Volatility. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2009. Published September 2009. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1979. Last previous edition approved in 2007 as D3828–07a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D3828-09. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3828 − 09
3
2.2 ISO Standards: 4.2.4 If improved accuracy is desired the procedure is
Guide 34 Quality Systems Guidelines for the Production of repeate
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3828–07a
Designations: 523/05 and 524/05 Designation:D3828–09
Standard Test Methods for
1
Flash Point by Small Scale Closed Cup Tester
This standard is issued under the fixed designation D3828; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
INTRODUCTION
The flash point method is generally used for testing a sample at a specific temperature. At a set
temperature, the specimen being tested and the air–vapor mixture above it are close to thermal
equilibrium. Test methods for other flash point equipment operated at a specific temperature are
described in Test Method D3941.
These small scale flash point methods are generally used for testing a sample at a specific
temperature where the specimen being tested and the air–vapor mixture above it are close to thermal
equilibrium. Test Method D3941 covers other flash point equipment operated at a specific
temperature.
Flash point values are a function of the apparatus design, the condition of the apparatus used, and
the operational procedure carried out. Flash point can therefore only be defined in terms of a standard
test method, and no general valid correlation can be guaranteed between results obtained by different
test methods, or with test apparatus different from that specified.
1. Scope*
1.1These test methods cover procedures for the determination of the flash point by a small scale closed tester. The procedures
may be used to determine the actual flash point temperature of a sample or whether a product will or will not flash at a specified
temperature (flash/no flash). When used in conjunction with an electronic thermal flash detector, these test methods are also
suitable for flash point tests on fatty acid methyl esters (FAME).
1.1 These test methods cover procedures for flash point tests, within the range of –30 to 300°C, of petroleum products and
biodiesel liquid fuels, using a small scale closed cup tester. The procedures may be used to determine, whether a product will or
will not flash at a specified temperature (flash/no flash Method A) or the flash point of a sample (Method B). When used in
conjunction with an electronic thermal flash detector, these test methods are also suitable for flash point tests on biodiesels such
as fatty acid methyl esters (FAME).
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to
heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk
of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire
risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular
end use. Warning—Mercury has been designated by EPAand many state agencies as a hazardous material that can cause central
nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware
that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.
1
These test methods are under the jurisdiction ofASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.08
on Volatility.
Current edition approved July 15, 2007. Published August 2007. Originally approved in 1979. Last previous edition approved in 2007 as D3828–07.
This is also a standard(s) of the Energy Institute issued under the fixed designations IP523 and IP524 (originally designated IP303).The final number indicates the year
of last revision. These test methods were originally adopted as a joint ASTM-IP standard in 1979.
Current edition approved Sept. 1, 2009. Published September 2009. Originally approved in 1979. Last previous edition approved in 2007 as D3828–07a.
*A Sum
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.