iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E1878-97(2013)

(Specification)

Standard Specification for Laboratory Glass Volumetric Flasks, Special Use

Standard Specification for Laboratory Glass Volumetric Flasks, Special Use

ABSTRACT
This specification covers the requirements for precision grade glass volumetric flasks for laboratories and specialty use. The products can be grouped into three styles according to size and shape. All products should be calibrated and should conform to the required shapes, volumetric tolerances, identification markings, capacity lines, quality of markings, and quality of laboratory marking spots.
SCOPE
1.1 This specification covers requirements for glass volumetric flasks of precision grades suitable for laboratory purposes and of specialty use. Each flask shall be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements. Flasks may be marked with an identification number (serial number) at the option of the manufacturer.Note 1—Specifications for standard volumetric flasks are given in specification E288.Note 2—Specifications for microvolumetric flasks in sizes from 1 to 25 mL are given in specification E237.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

General Information

Status
Historical
Publication Date
31-Oct-2013
ICS
71.040.20 - Laboratory ware and related apparatus
81.040.30 - Glass products
Technical Committee
E41 - Laboratory Apparatus
Drafting Committee
E41.01 - Laboratory Ware and Supplies
Current Stage
Ref Project

Relations

Replaces
ASTM E1878-97(2008) - Standard Specification for Laboratory Glass Volumetric Flasks, Special Use
Effective Date
01-Nov-2013
Replaced By
ASTM E1878-97(2019) - Standard Specification for Laboratory Glass Volumetric Flasks, Special Use
Effective Date
01-Jul-2019
Referred By
ASTM E694-18 - Standard Specification for Laboratory Glass Volumetric Apparatus
Effective Date
01-Nov-2013

Buy Standard

ASTM E1878-97(2013) - Standard Specification for Laboratory Glass Volumetric Flasks, Special UseASTM E1878-97(2013) - Standard Specification for Laboratory Glass Volumetric Flasks, Special Use
PreviousNext
Technical specification
ASTM E1878-97(2013) - Standard Specification for Laboratory Glass Volumetric Flasks, Special Use
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E1878 −97 (Reapproved 2013)
Standard Specification for
1
Laboratory Glass Volumetric Flasks, Special Use
This standard is issued under the fixed designation E1878; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1157 Specification for Sampling and Testing of Reusable
Laboratory Glassware
1.1 This specification covers requirements for glass volu-
metric flasks of precision grades suitable for laboratory pur-
3. Styles
poses and of specialty use. Each flask shall be marked with the
letter “A” to signify compliance with applicable construction
3.1 Style 1—Bates, sugar, wide neck, size 100 mL
and accuracy requirements. Flasks may be marked with an
3.2 Style 2—Kohlraush, enlarged cup, sizes 100, 200, and
identification number (serial number) at the option of the
500 mL
manufacturer.
3.3 Style 3—Sugar, two graduations, sizes 100 to 110 and
NOTE 1—Specifications for standard volumetric flasks are given in
200 to 220 mL
specification E288.
NOTE 2—Specifications for microvolumetric flasks in sizes from 1 to 25
mL are given in specification E237. 4. General Requirements
1.2 The values stated in SI units are to be regarded as
4.1 Calibration—flasks calibrate in accordance with the
standard. No other units of measurement are included in this
methods outlined in Practice E542.
standard.
4.2 General—See Specification E694 for general require-
ments not covered in this specification.
2. Referenced Documents
2
2.1 ASTM Standards:
5. Design
E237 Specification for Laboratory Glass Microvolumetric
5.1 Shape—Style 1 and 3 flask necks shall be designed with
Vessels (Volumetric Flasks and Centrifuge Tubes)
re-inforced rims for acceptance of rubber stopper or may be
E288 Specification for Laboratory Glass Volumetric Flasks
flared. Style 2 shall have a neck with an enlarged cup beaded
E438 Specification for Glasses in Laboratory Apparatus
to accept a rubber stopper. Flask shapes shall permit complete
E542 Practice for Calibration of Laboratory Volumetric
emptying and thorough cleaning. The area of the bottom or
Apparatus
base shall be of sufficient size so the flask, when empty, shall
E694 Specification for Laboratory Glass Volumetric Appa-
stand on an inclined plane of 15° to the horizontal.
ratus
5.2 Volumetric Tolerances—Flasks shall be in accordance
E920 Specification for Commercially Packaged Laboratory
Apparatus with tolerances appearing in Table 1.
E921 Specification for Export Packaged Laboratory Appa-
5.3 Markings—All markings shall be permanent and leg-
ratus
ible.
E1133 Practice for Performance Testing of Packaged Labo-
5.3.1 Capacity Line—The capacity line shall be sharply
ratory Apparatus for United States Government Procure-
defined and of uniform width in a plane parallel to the base of
ments
the flask. The line shall be applied by one of the following
methods; etched and filled with a permanent pigment; en-
graved; by application of a stain fired into the glass without
1
This specification is under the jurisdiction of ASTM Committee E41 on etching or by application of an
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1878-97(2019)(Specification)
Standard Specification for Laboratory Glass Volumetric Flasks, Special Use

ABSTRACT
This specification covers the requirements for precision grade glass volumetric flasks for laboratories and specialty use. The products can be grouped into three styles according to size and shape. All products should be calibrated and should conform to the required shapes, volumetric tolerances, identification markings, capacity lines, quality of markings, and quality of laboratory marking spots.
SCOPE
1.1 This specification covers requirements for glass volumetric flasks of precision grades suitable for laboratory purposes and of specialty use. Each flask shall be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements. Flasks may be marked with an identification number (serial number) at the option of the manufacturer.
Note 1: Specifications for standard volumetric flasks are given in Specification E288.
Note 2: Specifications for microvolumetric flasks in sizes from 1 to 25 mL are given in Specification E237.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E438-92(2018)(Specification)
Standard Specification for Glasses in Laboratory Apparatus

ABSTRACT
This specification covers the glasses commonly used to manufacture laboratory glass apparatus. Three types of glasses are included: Type I, Class A which is a low-expansion borosilicate glass, Type I, Class B which is an alumino-borosilicate glass, and Type II which is a soda-lime glass. Different tests shall be conducted in order to determine the following properties of glasses: linear coefficient of expansion, annealing point, softening point, density, and chemical durability.
SCOPE
1.1 This specification covers the glasses commonly used to manufacture laboratory glass apparatus.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1878-97(2019)(Specification)
Standard Specification for Laboratory Glass Volumetric Flasks, Special Use

ABSTRACT
This specification covers the requirements for precision grade glass volumetric flasks for laboratories and specialty use. The products can be grouped into three styles according to size and shape. All products should be calibrated and should conform to the required shapes, volumetric tolerances, identification markings, capacity lines, quality of markings, and quality of laboratory marking spots.
SCOPE
1.1 This specification covers requirements for glass volumetric flasks of precision grades suitable for laboratory purposes and of specialty use. Each flask shall be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements. Flasks may be marked with an identification number (serial number) at the option of the manufacturer.
Note 1: Specifications for standard volumetric flasks are given in Specification E288.
Note 2: Specifications for microvolumetric flasks in sizes from 1 to 25 mL are given in Specification E237.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E438-92(2018)(Specification)
Standard Specification for Glasses in Laboratory Apparatus

ABSTRACT
This specification covers the glasses commonly used to manufacture laboratory glass apparatus. Three types of glasses are included: Type I, Class A which is a low-expansion borosilicate glass, Type I, Class B which is an alumino-borosilicate glass, and Type II which is a soda-lime glass. Different tests shall be conducted in order to determine the following properties of glasses: linear coefficient of expansion, annealing point, softening point, density, and chemical durability.
SCOPE
1.1 This specification covers the glasses commonly used to manufacture laboratory glass apparatus.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off