ASTM F2830-11(2017)

Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer

ABSTRACT
This specification covers manufacturing and joining requirements for peelable or skinned polyethylene (PE) pipe, which is PE pipe meeting the requirements of Specification D2513, with a peelable outer layer of polypropylene (PP). The peelable PP layer does not contribute to outside diameter and wall thickness used for pressure rating or tensile loading calculations.
SCOPE
1.1 This standard specification covers manufacturing and joining requirements for peelable (skinned) polyethylene (PE) pipe, which is PE pipe meeting the requirements of Specification D2513, with a peelable outer layer of polypropylene (PP). These requirements are in addition to those in Specification D2513 for the PE pipe.  
1.2 The peelable PP layer does not contribute to outside diameter and wall thickness used for pressure rating or tensile loading calculations.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-Jul-2017
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.60 - Gas

Relations

• Replaces: ASTM F2830-11 - Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
• Effective Date: 01-Aug-2017
• Refers: ASTM D4101-24 - Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
• Effective Date: 01-Feb-2024
• Refers: ASTM F1563-23 - Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
• Effective Date: 01-Nov-2023
• Refers: ASTM F412-20 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Apr-2020
• Refers: ASTM F1563-01(2019) - Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
• Effective Date: 01-Aug-2019
• Refers: ASTM F412-19 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Jan-2019
• Refers: ASTM D2513-18 - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• Effective Date: 15-Apr-2018
• Refers: ASTM D1600-18 - Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
• Effective Date: 01-Jan-2018
• Refers: ASTM F412-17a - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Aug-2017
• Refers: ASTM F412-17 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Feb-2017
• Refers: ASTM D2513-16a - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• Effective Date: 15-Dec-2016
• Refers: ASTM D2513-16 - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• Effective Date: 01-Dec-2016
• Refers: ASTM F412-16a - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 15-Nov-2016
• Refers: ASTM F1055-16 - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
• Effective Date: 01-Aug-2016
• Refers: ASTM F412-16 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Aug-2016

Overview

ASTM F2830-11(2017), "Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer," establishes requirements for the manufacture and joining of PE gas pressure pipes that feature a peelable polypropylene outer layer. Developed by ASTM International, this standard applies to PE pipes compliant with ASTM D2513, featuring an outer PP layer designed for temporary protection and ease of removal prior to installation. The peelable PP layer does not contribute to the pipe’s pressure rating or tensile loading calculations and serves specific protective and identification purposes.

Key Topics

• Peelable Polypropylene (PP) Outer Layer: The PP layer is partially bonded to the PE pipe, permitting straightforward removal without affecting the pipe integrity. It must meet specific peel force and impact resistance requirements to ensure performance.
• Material Requirements: The underlying PE pipe must comply with ASTM D2513 standards for gas pressure pipes, while the PP outer layer must conform to ASTM D4101.
• Marking: Pipes must be clearly marked on the PP layer, including the designation "ASTM F2830" and the phrase "Peelable Pipe," to distinguish them from standard PE gas pipes.
• Joining Procedures: Before joining (via butt fusion, saddle fusion, socket fusion, electrofusion, or mechanical fittings), the PP layer must be completely removed using manufacturer-recommended tools, safeguarding the integrity of the PE surface for consistent joints.
• Testing: Conformance with peel force testing (ISO 17454) and impact testing (EN 1411) is required to verify the performance and removability of the PP layer.

Applications

• Gas Distribution Networks: Peelable skinned PE gas pipes are widely used in underground gas distribution systems where the PP layer protects against UV exposure and mechanical damage during storage, transportation, and handling.
• Extended Outdoor Storage: The PP outer layer allows pipes to be stored outdoors for up to five years by shielding the PE material from degradation due to UV radiation.
• Simplified Installation: The removable layer prevents the need for additional pipe cleaning prior to fusion joining, improving installation efficiency and joint reliability.
• Field Identification: Bright yellow color with brown stripes on the PP layer provides clear visual identification, reducing errors during construction and maintenance.

Related Standards

The following standards are referenced in ASTM F2830-11(2017) or closely associated with PE gas pipe manufacture and joining:

• ASTM D2513: Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• ASTM D4101: Specification for Polypropylene Injection and Extrusion Materials
• ASTM F412: Terminology Relating to Plastic Piping Systems
• ASTM F1055: Specification for Electrofusion Type Polyethylene Fittings
• ASTM F1563: Specification for Tools to Squeeze-off Polyethylene (PE) Pipe or Tubing
• ISO 17454: Plastics piping systems – Multilayer pipe – Test method for the adhesion of the different layers
• EN 1411: Plastics piping and ducting systems – Determination of resistance to external blows

Practical Value

Adhering to ASTM F2830-11(2017) ensures conformity with international best practices, enhancing the performance, safety, and traceability of PE gas pressure pipes with peelable PP layers. This standard supports utility providers, designers, and contractors in delivering reliable and compliant gas distribution infrastructure, while also providing critical guidance on marking, storage, and installation protocols to optimize both short-term handling and long-term operation.

Keywords: ASTM F2830, PE gas pressure pipe, peelable PP layer, polyethylene, polypropylene, gas pipe joining, pipe manufacturing, UV protection, electrofusion, underground gas pipe, industry standards

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F2830 −11 (Reapproved 2017) An American National Standard
Standard Specification for
Manufacture and Joining of Polyethylene (PE) Gas Pressure
Pipe With a Peelable Polypropylene (PP) Outer Layer
This standard is issued under the fixed designation F2830; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
1.1 This standard specification covers manufacturing and
D2513 Specification for Polyethylene (PE) Gas Pressure
joining requirements for peelable (skinned) polyethylene (PE)
Pipe, Tubing, and Fittings
pipe, which is PE pipe meeting the requirements of Specifica-
D4101 Specification for Polypropylene Injection and Extru-
tion D2513, with a peelable outer layer of polypropylene (PP).
sion Materials
These requirements are in addition to those in Specification
F412 Terminology Relating to Plastic Piping Systems
D2513 for the PE pipe.
F1055 Specification for Electrofusion Type Polyethylene
1.2 The peelable PP layer does not contribute to outside
Fittings for Outside Diameter Controlled Polyethylene
diameter and wall thickness used for pressure rating or tensile
and Crosslinked Polyethylene (PEX) Pipe and Tubing
loading calculations.
F1563 Specification for Tools to Squeeze-off Polyethylene
(PE) Gas Pipe or Tubing
1.3 The text of this standard references notes and footnotes
which provide explanatory material. These notes and footnotes
2.2 ISO Standard:
(excluding those in figures and tables) shall not be considered
ISO 17454 Plastics piping systems - multilayer pipe - test
as requirements of the standard.
method for the adhesion of the different layers using a
pulling rig.
1.4 Units—The values stated in inch-pound units are to be
2.3 EN Standard:
regarded as standard. The values given in parentheses are
EN 1411 - Plastics piping and ducting systems – Thermo-
mathematical conversions to SI units that are provided for
plastics pipes – determination of resistance to external
information only and are not considered standard.
blows by the staircase method.
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to establish appro-
3.1 Definitions—Definitions are in accordance with Termi-
priate safety, health, and environmental practices and deter-
nology F412, and abbreviations are in accordance with Termi-
mine the applicability of regulatory limitations prior to use.
nology D1600, unless otherwise specified.
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
3.2 Definitions of Terms Specific to This Standard:
ization established in the Decision on Principles for the
3.2.1 Peelable pipe, n—Specification D2513 polyethylene
Development of International Standards, Guides and Recom-
(PE) pipe coextruded with a peelable outer layer of polypro-
mendations issued by the World Trade Organization Technical
pylene (PP). When the peelable PP layer is removed, the PE
Barriers to Trade (TBT) Committee.
pipe is the same as D2513 PE pipe.
2. Referenced Documents
4. PE Pipe and PP Layer Requirements
2.1 ASTM Standards:
4.1 PE Pipe Requirements:
4.1.1 The PE pipe shall meet all the requirements of
Specification D2513, excluding marking, when tested in accor-
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
dance with 6.1. Marking shall be in accordance with Section 7.
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved Aug. 1, 2017. Published September 2017. Originally
approved in 2011. Last previous edition approved in 2011 as F2830–11. DOI:
10.1520/F2830-11R17. Available from International Organization for Standardization (ISO), 1, ch. de
For referenced ASTM standards, visit the ASTM website, www.astm.org, or la Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http://
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM www.iso.ch.
Standards volume information, refer to the standard’s Document Summary page on Available from European Committee for Standardization (CEN), 36 rue de
the ASTM website. Stassart, B-1050, Brussels, Belgium, http://www.cenorm.be.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2830−11 (2017)
4.2 PP Layer Requirements: 6. Test Methods
4.2.1 The PP peelable layer shall be made from unrein-
6.1 PE Pipe Testing—To determine conformance to Speci-
forced PP material in accordance with Specification D4101.
fication D2513, the PE pipe shall be tested exclusive of the
Any unreinforced PP material may be used as long as the
co-extruded PP peelable layer.
peelablepipemeetsthepeelforceandimpacttestrequirements
6.2 PA Peel Force—the peel for
...