ASTM F2600-09
(Specification)Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
SCOPE
1.1 This specification covers polyamide-11 electrofusion fittings for use with outside diameter-controlled polyamide-11 pipe, covered by Specification D 2513. Requirements for materials, workmanship, and testing performance are included. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.”
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2600 −09 AnAmerican National Standard
Standard Specification for
Electrofusion Type Polyamide-11 Fittings for Outside
1
Diameter Controlled Polyamide-11 Pipe and Tubing
This standard is issued under the fixed designation F2600; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D6779 Classification System for and Basis of Specification
for Polyamide Molding and Extrusion Materials (PA)
1.1 This specification covers polyamide-11 electrofusion
F412 Terminology Relating to Plastic Piping Systems
fittings for use with outside diameter-controlled polyamide-11
F905 Practice for Qualification of Polyethylene Saddle-
pipe, covered by Specification D2513. Requirements for
Fused Joints
materials, workmanship, and testing performance are included.
Whereapplicableinthisspecification“pipe”shallmean“pipe”
3. Terminology
or “tubing.”
3.1 Definitions—Definitions are in accordance with Termi-
1.2 The values stated in inch-pound units are to be regarded
nology F412, and abbreviations are in accordance with Termi-
as standard. The values given in parentheses are mathematical
nology D1600, unless otherwise specified.
conversions to SI units that are provided for information only
3.2 Definitions of Terms Specific to This Standard:
and are not considered standard.
3.2.1 electrofusion—a heat fusion joining process where the
1.3 The following safety hazards caveat pertains only to the
heat source is an integral part of the fitting, such that when
test method portion, Section 9, of this specification: This
electric current is applied, heat is produced that melts and joins
standard does not purport to address all of the safety concerns,
the plastics.
if any, associated with its use. It is the responsibility of the user
3.2.2 fusion interface—surface in the heat fusion process
of this standard to establish appropriate safety and health
where the plastic materials of the products being joined bond
practices and determine the applicability of regulatory limita-
together.
tions prior to use.
3.2.3 fusion zone length—total length of the melted material
2. Referenced Documents
in the fitting cross-section under evaluation.
2
2.1 ASTM Standards:
4. Materials and Manufacture
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
4.1 This specification covers fittings made from polyamide
D1598 Test Method for Time-to-Failure of Plastic Pipe 11 (PA11) meeting the requirements for Group 3, Class 2, and
Under Constant Internal Pressure
Grade 3, (PA32312) as prescribed in Specification D6779.
D1599 Test Method for Resistance to Short-Time Hydraulic
4.2 Rework Material—Clean rework polyamide-11 material
Pressure of Plastic Pipe, Tubing, and Fittings
of the same resin, free of any wire or contaminants generated
D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
from the fitting manufacturer’s own production, may be used
tics
by the same manufacturer, as long as the fittings produced
D2122 Test Method for Determining Dimensions of Ther-
conform to the requirements of this specification.
moplastic Pipe and Fittings
4.3 Heating Mechanism—The heat mechanism shall be of
D2513 Specification for Thermoplastic Gas Pressure Pipe,
materials not detrimental to the performance of the fitting or
Tubing, and Fittings
the pipe to which it is intended to be joined.
1
5. Performance Requirements
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
5.1 The following requirements are for electrofusion joints
Current edition approved April 1, 2009. Published April 2009. Originally
that have been joined using the manufacturer’s recommended
approved in 2006. Last previous edition approved in 2006 as F2600–06. DOI:
10.1520/F2600-09.
joining procedures. These requirements must be met by each
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
electrofusion joint design, on each size and type of pipe
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
material for which the manufacturer recommends use of his
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. fitting. Any revisions to the electrofusion joint design or
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2600−09
processing by the manufacturer after the initial testing requires 6.3 The manufacturer shall furnish to the user the electrical
retest
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2600–06 Designation: F 2600 – 09
Standard Specification for
Electrofusion Type Polyamide-11 Fittings for Outside
1
Diameter Controlled Polyamide-11 Pipe and Tubing
This standard is issued under the fixed designation F 2600; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers polyamide-11 electrofusion fittings for use with outside diameter-controlled polyamide-11 pipe,
covered by Specification D 2513. Requirements for materials, workmanship, and testing performance are included. Where
applicable in this specification “pipe” shall mean “pipe” or “tubing.”
1.2The values stated in inch-pound and centigrade temperature units are to be regarded as standard. The values given in
parentheses are for information only.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 618 Practice for Conditioning Plastics for Testing
D 638 Test Method for Tensile Properties of Plastics
D 1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D 1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D 1600 Terminology for Abbreviated Terms Relating to Plastics
D 2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D 2513 Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
D4066 6779 Classification System for Nylon InjectionPolyamide Molding and Extrusion Materials (PA)
F 412 Terminology Relating to Plastic Piping Systems
F 905 Practice for Qualification of Polyethylene Saddle-Fused Joints
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F 412, and abbreviations are in accordance with Terminology
D 1600, unless otherwise specified.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 electrofusion—a heat fusion joining process where the heat source is an integral part of the fitting, such that when electric
current is applied, heat is produced that melts and joins the plastics.
3.2.2 fusion interface—surfaceintheheatfusionprocesswheretheplasticmaterialsoftheproductsbeingjoinedbondtogether.
3.2.3 fusion zone length—total length of the melted material in the fitting cross-section under evaluation.
4. Materials and Manufacture
4.1 Thisspecificationcoversfittingsmadefrompolyamide11(PA11)meetingtherequirementsforGroup3,Class2,andGrade
3, (PA32312) as prescribed in Specification D4066D 6779.
4.2 Rework Material—Cleanreworkpolyamide-11materialofthesameresin,freeofanywireorcontaminantsgeneratedfrom
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved Sept. 1, 2006. Published September 2006.
Current edition approved April 1, 2009. Published April 2009. Originally approved in 2006. Last previous edition approved in 2006 as F 2600–06.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2600–09
the fitting manufacturer’s own production, may be used by the same manufacturer, as long as the fittings produced conform to the
requirements of this specification.
4.3 Heating Mechanism—The heat mechanism shall be of materials not detrimental to the performance of the fitting or the pipe
to which it is intended to be joined.
5. Performance Requirements
5.1 Thefollowingrequi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.