ASTM B152/B152M-06ae1

Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

ABSTRACT
This standard covers the requirements for copper sheet, strip, plate, and rolled bar produced from copper with the following UNS Nos.; C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910, C11000, C11300, C11400, C11600, C12000, C12200, C12300, C14200, C14420, and C14530. Chemical composition shall conform to the chemical requirements pertaining to the materials UNS No. Tempering of materials shall be done by hot-rolling, cold rolling, and annealing. Copper material shall meet the maximum limit of electrical resistivity as indicated. The material shall undergo tensile strength, Rockwell hardness, and plate item tests to conform with the mechanical proptery requirement of the specification. The material shall also be capable of passing microscopical examination and embrittlement test, but not required by the specification.
SCOPE
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Sep-2006
• ICS: 77.150.30 - Copper products
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.01 - Plate, Sheet, and Strip

Relations

• Replaces: ASTM B152/B152M-06a - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• Effective Date: 01-Oct-2006
• Replaced By: ASTM B152/B152M-09 - Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
• Effective Date: 01-Oct-2009
• Referred By: ASTM E18-22 - Standard Test Methods for Rockwell Hardness of Metallic Materials
• Effective Date: 01-Oct-2006
• Referred By: ASTM D1002-10(2019) - Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
• Effective Date: 01-Oct-2006
• Referred By: ASTM B248-22 - Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
• Effective Date: 01-Oct-2006
• Referred By: ASTM D3658-01(2016) - Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints
• Effective Date: 01-Oct-2006
• Referred By: ASTM D3528-96(2016) - Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
• Effective Date: 01-Oct-2006
• Referred By: ASTM D849-15(2019)e1 - Standard Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons
• Effective Date: 01-Oct-2006
• Referred By: ASTM D3165-07(2023) - Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
• Effective Date: 01-Oct-2006
• Referred By: ASTM F2798-09(2023) - Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
• Effective Date: 01-Oct-2006
• Referred By: ASTM C764-19 - Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation
• Effective Date: 01-Oct-2006
• Referred By: ASTM B248M-22 - Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
• Effective Date: 01-Oct-2006
• Referred By: ASTM D3433-99(2020) - Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints
• Effective Date: 01-Oct-2006
• Referred By: ASTM C739-21a - Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation
• Effective Date: 01-Oct-2006
• Referred By: ASTM F68-16 - Standard Specification for Oxygen-Free Copper in Wrought Forms for Electron Devices
• Effective Date: 01-Oct-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Used in USDOE-NE standards
´1
Designation: B152/B152M – 06a
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B152/B152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 4 was editorially corrected in February 2008.
NOTE 2—Thisspecificationisnotintendedtoestablishrequirementsfor
1. Scope*
material rolled to ounce-weight thicknesses. Such material is defined in
2
1.1 This specification establishes the requirements for cop-
Specification B370.
per sheet, strip, plate, and rolled bar produced from the
Plates for locomotive fireboxes are defined in Specification B11.
following coppers.
Flatcopperproductswithfinished(rolledordrawn)edges(flatwireand
strip) are defined in Specification B272.
Previous
Copper
Designa-
A
UNS No. Type of Copper
1.1.1 When a specific copper is not identified in the contract
tion
orpurchaseorder,thesuppliermayfurnishproductfromanyof
B
C10100 OFE Oxygen-free electronic
the listed coppers.
B
C10200 OF Oxygen-free without residual
1.2 The values stated in inch-pound or SI units are to be
deoxidants
C10300 . Oxygen-free extra low phosphorus
regarded separately as standard. The values in each system are
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
not exact equivalents; therefore, each system shall be used
C10800 . Oxygen-free low phosphorus
independently of the other. Combining values from the two
C10910 . Low oxygen
B
C11000 ETP Electrolytic tough pitch systems may result in nonconformance with the specification.
B
C11300, C11400, C11600 STP Silver bearing tough pitch
1.3 The following safety hazards caveat only pertains to the
C12000 DLP Phosphorized, low residual phos-
test method portion, Section 13 of this specification: This
phorus
B
C12200 DHP Phosphorized, high residual phos- standard does not purport to address all of the safety concerns,
phorus
if any, associated with its use. It is the responsibility of the user
C12300 DPS Phosphorized, silver bearing
of this standard to establish appropriate safety and health
C14200 DPA Phosphorus deoxidized, arsenical
C14420 . Tin bearing tellurium copper
practices and determine the applicability of regulatory limita-
C14530 . Tin tellurium bearing copper
tions prior to use.
_______________
A
Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxi-
2. Referenced Documents
dized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium
34
2.1 ASTM Standards:
bearing) these types of copper are classified in Classification B224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE B11 Discontinued1981;SpecificationforCopperPlatesfor
4
Specification CA102 conforms to the requirements for Copper UNS No. C10200;
Locomotive Fireboxes
SAE Specification CA110 conforms to the requirements for Copper UNS No.
B170 Specification for Oxygen-Free Electrolytic Copper—
C11000; SAE Specifications CA113, CA114, and CA116 conform to the require-
ments for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification Refinery Shapes
CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122
B193 Test Method for Resistivity of Electrical Conductor
conforms to the requirements for Copper UNS No. C12200.
Materials
NOTE 1—Eachofthecopperslistedhasuniquepropertiesthatcanmake
B216 Specification for Tough-Pitch Fire-Refined Copper—
it suitable for specific applications. The purchaser should consult with the
Refinery Shapes
supplier to determine which copper would be best suited for the intended
B224 Classification of Coppers
application.
B248 Specification for General Requirements for Wrought
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
Bar
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
andCopperAlloysandisthedirectresponsibilityofSubcommitteeB05.01onPlate,
Sheet, and Strip.
3
Current edition approved Oct. 1, 2006. Published October 2006. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1942. Last previous edition approved in 2006 as B152/B152M – 06. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
DOI: 10.1520/B0152_B0152M-06AE01. Standards volume information, refer to the standard’s Document Summary page on
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- the ASTM website.
4
cation SB-152 in Section 11 of that Code. Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Bar
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE standards
´1
Designation:B152/B152M–06a Designation: B 152/B 152M – 06a
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B 152/B 152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—Table 4 was editorially corrected in February 2008.
1. Scope*
2
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following
coppers.
Previous
Copper
Designa-
A
UNS No. Type of Copper
tion
B
C10100 OFE Oxygen-free electronic
B
C10200 OF Oxygen-free without residual
deoxidants
C10300 . Oxygen-free extra low phosphorus
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
C10800 . Oxygen-free low phosphorus
C10910 . Low oxygen
B
C11000 ETP Electrolytic tough pitch
B
C11300, C11400, C11600 STP Silver bearing tough pitch
C12000 DLP Phosphorized, low residual phos-
phorus
B
C12200 DHP Phosphorized, high residual phos-
phorus
C12300 DPS Phosphorized, silver bearing
C14200 DPA Phosphorus deoxidized, arsenical
C14420 . Tin bearing tellurium copper
C14530 . Tin tellurium bearing copper
_______________
A
Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these
types of copper are classified in Classification B 224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE
Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper
UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements
for Copper UNS No. C12200.
NOTE 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the
supplier to determine which copper would be best suited for the intended application.
NOTE 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in
Specification B 370.
Plates for locomotive fireboxes are defined in Specification B 11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B 272.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of
the listed coppers.
1.2 Thevaluesstatedininch-poundorSIunitsaretoberegardedseparatelyasstandard.Thevaluesineachsystemarenotexact
equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result
in nonconformance with the specification.
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1942. Last previous edition approved in 2006 as B 152/B 152M – 06.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-152 in Section 11 of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
B 152/B 152M – 06a
2. Referenced Documents
3
2.1 ASTM Standards:
4
B11 Specification for Copper Plates for Locomotive Fireboxes
B 170 Specification for Oxygen-Free Electrolytic CopperRefinery Shapes
B 193 Test Method for Resistivity of Electrical Conductor Materials
B 216 Specificatio
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE standards
e1
Designation:B152/B152M–06a Designation: B 152/B 152M – 06a
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B 152/B 152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Table 4 was editorially corrected in February 2008.
1. Scope*
2
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following
coppers.
Previous
Copper
Designa-
A
UNS No. Type of Copper
tion
B
C10100 OFE Oxygen-free electronic
B
C10200 OF Oxygen-free without residual
deoxidants
C10300 . Oxygen-free extra low phosphorus
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
C10800 . Oxygen-free low phosphorus
C10910 . Low oxygen
B
C11000 ETP Electrolytic tough pitch
B
C11300, C11400, C11600 STP Silver bearing tough pitch
C12000 DLP Phosphorized, low residual phos-
phorus
B
C12200 DHP Phosphorized, high residual phos-
phorus
C12300 DPS Phosphorized, silver bearing
C14200 DPA Phosphorus deoxidized, arsenical
C14420 . Tin bearing tellurium copper
C14530 . Tin tellurium bearing copper
_______________
A
Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these
types of copper are classified in Classification B 224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE
Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper
UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements
for Copper UNS No. C12200.
NOTE 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the
supplier to determine which copper would be best suited for the intended application.
NOTE 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in
Specification B 370.
Plates for locomotive fireboxes are defined in Specification B 11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B 272.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of
the listed coppers.
1.2 Thevaluesstatedininch-poundorSIunitsaretoberegardedseparatelyasstandard.Thevaluesineachsystemarenotexact
equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result
in nonconformance with the specification.
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1942. Last previous edition approved in 2006 as B 152/B 152M – 06.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-152 in Section 11 of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
B 152/B 152M – 06a
2. Referenced Documents
3
2.1 ASTM Standards:
4
B 11 Specification for Copper Plates for Locomotive Fireboxes
B 170 Specification for Oxygen-Free Electrolytic CopperRefinery Shapes
B 193 Test Method for Resistivity of Electrical Conductor Materials
B 216 Specificati
...