ASTM B152/B152M-13
(Specification)Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
ABSTRACT
This standard covers the requirements for copper sheet, strip, plate, and rolled bar produced from copper with the following UNS Nos.; C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910, C11000, C11300, C11400, C11600, C12000, C12200, C12300, C14200, C14420, and C14530. Chemical composition shall conform to the chemical requirements pertaining to the materials UNS No. Tempering of materials shall be done by hot-rolling, cold rolling, and annealing. Copper material shall meet the maximum limit of electrical resistivity as indicated. The material shall undergo tensile strength, Rockwell hardness, and plate item tests to conform with the mechanical proptery requirement of the specification. The material shall also be capable of passing microscopical examination and embrittlement test, but not required by the specification.
SCOPE
1.1 This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
Copper
UNS No.A
Previous
Designation
Type of Copper
C10100B
OFE
Oxygen-free electronic
C10200B
OF
Oxygen-free without residual
deoxidants
C10300
...
Oxygen-free extra low phosphorus
C10400, C10500, C10700
OFS
Oxygen-free, silver bearing
C10800
...
Oxygen-free low phosphorus
C10910
...
Low oxygen
C11000B,C
ETP,
TPC
Electrolytic tough pitchC, Tough pitchC
C11300, C11400, C11600B
STP
Silver bearing tough pitch
C12000
DLP
Phosphorized, low residual phos-
phorus
C12200B
DHP
Phosphorized, high residual phos-
phorus
C12300
DPS
Phosphorized, silver bearing
C14200
DPA
Phosphorus deoxidized, arsenical
C14420
...
Tin bearing tellurium copper
C14530
...
Tin tellurium bearing copper
_______________ A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200.C Unless specified in the contract or purchase order the supplier is permitted to provide ETP copper or TP copper.Note 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application.Note 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in Specification B370.
Plates for locomotive fireboxes are defined in Specification B11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associate...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B152/B152M −13 Used in USDOE-NE standards
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B152/B152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
NOTE2—Thisspecificationisnotintendedtoestablishrequirementsfor
1. Scope*
material rolled to ounce-weight thicknesses. Such material is defined in
2
1.1 This specification establishes the requirements for cop-
Specification B370.
per sheet, strip, plate, and rolled bar produced from the Plates for locomotive fireboxes are defined in Specification B11.
Flatcopperproductswithfinished(rolledordrawn)edges(flatwireand
following coppers.
strip) are defined in Specification B272.
Previous
Copper
Designation
1.1.1 When a specific copper is not identified in the contract
A
UNS No. Type of Copper
orpurchaseorder,thesuppliermayfurnishproductfromanyof
B
the listed coppers.
C10100 OFE Oxygen-free electronic
B
C10200 OF Oxygen-free without residual
1.2 The values stated in either SI units or inch-pound units
deoxidants
are to be regarded separately as standard. The values stated in
C10300 . Oxygen-free extra low phosphorus
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
each system may not be exact equivalents; therefore, each
C10800 . Oxygen-free low phosphorus
system shall be used independently of the other. Combining
C10910 . Low oxygen
B,C C
values from the two systems may result in non-conformance
C11000 ETP, Electrolytic tough pitch , Tough
C
C
pitch
TP
with the standard.
B
C11300, C11400, C11600 STP Silver bearing tough pitch
C12000 DLP Phosphorized, low residual phos- 1.3 The following safety hazards caveat only pertains to the
phorus
test method portion, Section 13 of this specification: This
B
C12200 DHP Phosphorized, high residual phos-
standard does not purport to address all of the safety concerns,
phorus
C12300 DPS Phosphorized, silver bearing if any, associated with its use. It is the responsibility of the user
C14200 DPA Phosphorus deoxidized, arsenical
of this standard to establish appropriate safety and health
C14420 . Tin bearing tellurium copper
practices and determine the applicability of regulatory limita-
C14530 . Tin tellurium bearing copper
_______________ tions prior to use.
A
2. Referenced Documents
Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus
deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium
3
2.1 ASTM Standards:
bearing) these types of copper are classified in Classification B224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specifi-
B11 Specification for Copper Plates for Locomotive Fire-
4
cation CA102 conforms to the requirements for Copper UNS No. C10200; SAE
boxes (Withdrawn 1980)
Specification CA110 conforms to the requirements for Copper UNS No. C11000;
B170 Specification for Oxygen-Free Electrolytic Copper—
SAE Specifications CA113, CA114, and CA116 conform to the requirements for
Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120
Refinery Shapes
conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to
B193 Test Method for Resistivity of Electrical Conductor
the requirements for Copper UNS No. C12200.
C
Materials
Unless specified in the contract or purchase order the supplier is permitted to
provide ETP copper or TP copper.
B216 Specification for Tough-Pitch Fire-Refined Copper—
Refinery Shapes
NOTE1—Eachofthecopperslistedhasuniquepropertiesthatcanmake
it suitable for specific applications. The purchaser should consult with the B224 Classification of Coppers
supplier to determine which copper would be best suited for the intended
B248 Specification for General Requirements for Wrought
application.
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
Bar
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
andCopperAlloysandisthedirectresponsibilityofSubcommitteeB05.01onPlate,
3
Sheet, and Strip. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 15, 2013. Published January 2013. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1942. Last previous edition approved in 2009 as B152/B152M – 09. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/B0152_B0152M-13. the ASTM website.
2 4
For ASME Boiler and Pressure Vessel Code applications see related Specifi- The last approved version of this historical standard is referenced on
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B152/B152M − 09 B152/B152M − 13 Used in USDOE-NE standards
Standard Specification for
1
Copper Sheet, Strip, Plate, and Rolled Bar
This standard is issued under the fixed designation B152/B152M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon («) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following
coppers.
Previous
Copper
Designation
A
UNS No. Type of Copper
B
C10100 OFE Oxygen-free electronic
B
C10200 OF Oxygen-free without residual
deoxidants
C10300 . Oxygen-free extra low phosphorus
C10400, C10500, C10700 OFS Oxygen-free, silver bearing
C10800 . Oxygen-free low phosphorus
C10910 . Low oxygen
B,C C
C11000 ETP, Electrolytic tough pitch , Tough
C
C
pitch
TP
B
C11300, C11400, C11600 STP Silver bearing tough pitch
C12000 DLP Phosphorized, low residual phos-
phorus
B
C12200 DHP Phosphorized, high residual phos-
phorus
C12300 DPS Phosphorized, silver bearing
C14200 DPA Phosphorus deoxidized, arsenical
C14420 . Tin bearing tellurium copper
C14530 . Tin tellurium bearing copper
_______________
A
Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these
types of copper are classified in Classification B224.
B
SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification
CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos.
C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper
UNS No. C12200.
C
Unless specified in the contract or purchase order the supplier is permitted to provide ETP copper or TP copper.
NOTE 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the
supplier to determine which copper would be best suited for the intended application.
NOTE 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in
Specification B370.
Plates for locomotive fireboxes are defined in Specification B11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of
the listed coppers.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
Current edition approved Oct. 1, 2009Jan. 15, 2013. Published November 2009January 2013. Originally approved in 1942. Last previous edition approved in 20062009
ε1
as B152/B152M – 06aB152/B152M – 09. . DOI: 10.1520/B0152_B0152M-09.10.1520/B0152_B0152M-13.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-152 in Section 11 of that Code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B152/B152M − 13
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification:This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
4
B11 Specification for C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.