ASTM D8111-18
(Test Method)Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine
Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine
SIGNIFICANCE AND USE
5.1 This test method was developed to evaluate automotive engine oils for protection against oil thickening and piston deposits during moderately high-speed, hightemperature service.
5.1.1 The increase in kinematic viscosity of the oil indicates the tendency of an oil to thicken because of oxidation. In automotive service, such thickening can cause oil pump starvation and resultant catastrophic engine failures.
5.1.2 The deposit ratings for an oil indicate the tendency for the formation of deposits throughout the engine, including those that can cause sticking of the piston rings in their grooves. In automotive service, such ring sticking can cause a loss of compression pressures in the engine.
5.2 The test method was developed to correlate with oils of known good and poor protection against oil thickening and piston deposits. Specially formulated oils that produce less than desirable results with unleaded fuels were also used during the development of this test.
5.3 The Sequence IIIH engine oil test has been recommended as a replacement for the Sequence IIIG test and is expected to be used in specifications and classifications of engine lubricating oils, such as the following:
5.3.1 Specification D4485.
5.3.2 Military Specification MIL-PRF-2104.
5.3.3 SAE Classification J183.
SCOPE
1.1 This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking, oil consumption, and phosphorus retention. Such oils include both single-viscosity and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.
1.1.1 Additionally, with nonmandatory supplemental requirements, a Sequence IIIHA Test (Mini Rotary Viscometer and Cold Cranking Simulator measurements), or a Sequence IIIHB Test (phosphorus retention measurement) can be conducted. These supplemental test procedures are contained in Appendix X1 and Appendix X2, respectively.
Note 1: Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions:
1.2.1.1 Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, and valve sizes and springs.
1.2.1.2 The ring end gaps in Table A8.7, the dimensions for the blowby ventilation support bracket in Fig. A3.2, and the torque wrenches in Table A8.1 are in inch-pound units.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 6.11.6, 7.1, 7.2.1, and 7.3.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D8111 − 18
Standard Test Method for
Evaluation of Automotive Engine Oils in the Sequence IIIH,
1
Spark-Ignition Engine
This standard is issued under the fixed designation D8111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Portions of this test method are written for use by laboratories that make use of ASTM Test
2
Monitoring Center (TMC) services (see Annex A1).
TheTMCprovidesreferenceoils,andengineeringandstatisticalservicestolaboratoriesthatdesire
to produce test results that are statistically similar to those produced by laboratories previously
calibrated by the TMC.
In general, the test purchaser decides if a calibrated test stand is to be used. Organizations such as
theAmericanChemistryCouncilrequirethatalaboratoryutilizetheTMCservicesaspartoftheirtest
registration process. In addition, the American Petroleum Institute and the Gear Lubricant Review
Committee of the Lubricant Review Institute (SAE International) require that a laboratory use the
TMC services in seeking qualification of oils against their specifications.
The advantage of using the TMC services to calibrate test stands is that the test laboratory (and
hence the test purchaser) has an assurance that the test stand was operating at the proper level of test
severity. It should also be borne in mind that results obtained in a non-calibrated test stand may not
be the same as those obtained in a test stand participating in the ASTM TMC services process.
NOTE 1—Companion test methods used to evaluate engine oil perfor-
1. Scope*
mance for specification requirements are discussed in SAE J304.
1.1 This test method covers an engine test procedure for
1.2 The values stated in SI units are to be regarded as
evaluating automotive engine oils for certain high-temperature
standard. No other units of measurement are included in this
performance characteristics, including oil thickening (as mea-
standard.
sured by kinematic viscosity increase), piston deposits, ring
sticking, oil consumption, and phosphorus retention. Such oils
1.2.1 Exceptions:
include both single-viscosity and multiviscosity grade oils that
1.2.1.1 WherethereisnodirectSIequivalentsuchasscrew
are used in both spark-ignition, gasoline-fueled engines, as
threads, national pipe threads/diameters, tubing sizes, and
well as in diesel engines.
valve sizes and springs.
1.1.1 Additionally, with nonmandatory supplemental
1.2.1.2 The ring end gaps in TableA8.7, the dimensions for
requirements, a Sequence IIIHATest (Mini RotaryViscometer
the blowby ventilation support bracket in Fig. A3.2, and the
and Cold Cranking Simulator measurements), or a Sequence
torque wrenches in Table A8.1 are in inch-pound units.
IIIHB Test (phosphorus retention measurement) can be con-
ducted. These supplemental test procedures are contained in
1.3 This standard does not purport to address all of the
Appendix X1 and Appendix X2, respectively.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1
This test method is under the jurisdiction of ASTM Committee D02 on
bility of regulatory limitations prior to use. Specific warning
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
statements are provided in 6.11.6, 7.1, 7.2.1, and 7.3.
Subcommittee D02.B0 on Automotive Lubricants.
Current edition approved April 1, 2018. Published May 2018. Originally
1.4 This international standard was developed in accor-
approved in 2017. Last previous edition approved in 2017 as D8111–17. DOI:
dance with internationally recognized principles on standard-
10.1520/D8111-18.
2
Until the next revision of this test method, theASTM Test Monitoring Center
ization established in the Decision on Principles for the
will update changes in the test method by means of information letters. Information
Development of International Standards, Guides and Recom-
lettersmaybeobtainedfromtheASTMTestMonitoringCenter,6555PennAvenue,
mendations issued by the World Trade Organization Technical
Pittsburgh, PA 15206-4489, Attention Administrator. This edition incorporates
revisions in all information letters through No. 17-5. Barriers to Trade (TBT) Committee.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D8111−18
2. Referenced Documents D5293Test Method for Apparent Viscosity
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D8111 − 17 D8111 − 18
Standard Test Method for
Evaluation of Automotive Engine Oils in the Sequence IIIH,
1
Spark-Ignition Engine
This standard is issued under the fixed designation D8111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Portions of this test method are written for use by laboratories that make use of ASTM Test
2
Monitoring Center (TMC) services (see Annex A1).
The TMC provides reference oils, and engineering and statistical services to laboratories that desire
to produce test results that are statistically similar to those produced by laboratories previously
calibrated by the TMC.
In general, the test purchaser decides if a calibrated test stand is to be used. Organizations such as
the American Chemistry Council require that a laboratory utilize the TMC services as part of their test
registration process. In addition, the American Petroleum Institute and the Gear Lubricant Review
Committee of the Lubricant Review Institute (SAE International) require that a laboratory use the
TMC services in seeking qualification of oils against their specifications.
The advantage of using the TMC services to calibrate test stands is that the test laboratory (and
hence the test purchaser) has an assurance that the test stand was operating at the proper level of test
severity. It should also be borne in mind that results obtained in a non-calibrated test stand may not
be the same as those obtained in a test stand participating in the ASTM TMC services process.
1. Scope Scope*
1.1 This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature
performance characteristics, including oil thickening (as measured by kinematic viscosity increase), piston deposits, ring sticking,
oil consumption, and phosphorus retention. Such oils include both single-viscosity and multiviscosity grade oils that are used in
both spark-ignition, gasoline-fueled engines, as well as in diesel engines.
1.1.1 Additionally, with nonmandatory supplemental requirements, a Sequence IIIHA Test (Mini Rotary Viscometer and Cold
Cranking Simulator measurements), or a Sequence IIIHB Test (phosphorus retention measurement) can be conducted. These
supplemental test procedures are contained in Appendix X1 and Appendix X2, respectively.
NOTE 1—Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exceptions:
1.2.1.1 Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, and valve
sizes and springs.
1.2.1.2 The ring end gaps in Table A8.7, the dimensions for the blowby ventilation support bracket in Fig. A3.2, and the torque
wrenches in Table A8.1 are in inch-pound units.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. Specific warning statements are provided in 6.11.6, 7.1, 7.2.1, and 7.3.
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.B0 on Automotive Lubricants.
Current edition approved May 1, 2017April 1, 2018. Published June 2017May 2018. Originally approved in 2017. Last previous edition approved in 2017 as D8111 – 17.
DOI: 10.1520/D8111–17.10.1520/D8111-18.
2
Until the next revision of this test method, the ASTM Test Monitoring Center will update changes in the test method by means of information letters. Information letters
may be obtained from the ASTM Test Monitoring Center, 6555 Penn Avenue, Pittsburgh, PA 15206-4489.15206-4489, Attention Administrator. This edition incorporates
revisions in all information letters through No. 17-5.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D8111 − 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.