ASTM C1540-09a

Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

ABSTRACT
This specification covers the performance evaluation of heavy duty shielded couplings to join hubless cast iron soil pipe and fittings. Physical properties of all stainless steel and gaskets shall comply with the specified values. Requirements for the elastomeric gasket, clamp assembly, and couplings such as coupling width are detailed. The test apparatus for deflection test, shear test, and unrestrained hydrostatic joint test are illustrated.
SCOPE
1.1 This specification covers the evaluating of the performance of heavy duty shielded couplings to join hubless cast iron soil pipe and fittings.
1.2 Couplings covered by this standard shall have minimum dimensions as found in Table 1 and Fig. 1 of this standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of comparable standards published by other organizations, namely Cast Iron Soil Pipe Institute specification CISPI 310 and Factory Mutual Research standard FM 1680.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
TABLE 1   Nominal Pipe SizeCoupling Width 1½ to 4 in. (38 to 100 mm)3 in. (76 mm) Minimum Width 5 to 10 in. (127 to 254 mm)4 in. (100 mm) Minimum Width 12 to 15 in. (305 to 381 mm)5½ in. (140 mm) Minimum Width
FIG. 1 Typical Center Stop Detail

General Information

• Status: Historical
• Publication Date: 14-Oct-2009
• ICS: 23.040.60 - Flanges, couplings and joints
• Technical Committee: A04 - Iron Castings
• Drafting Committee: A04.75 - Gaskets and Coupling for Plumbing and Sewer Piping

Relations

• Replaces: ASTM C1540-09 - Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 15-Oct-2009
• Replaced By: ASTM C1540-11 - Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 01-Jun-2011
• Referred By: ASTM C1277-20 - Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 15-Oct-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1540 – 09a
Standard Specification for
Heavy Duty Shielded Couplings Joining Hubless Cast Iron
1
Soil Pipe and Fittings
This standard is issued under the fixed designation C1540; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
TABLE 1
1. Scope
Nominal Pipe Size Coupling Width
1.1 This specification covers the evaluating of the perfor-
1
1 ⁄2 to 4 in. (38 to 100 mm) 3 in. (76 mm) Minimum Width
mance of heavy duty shielded couplings to join hubless cast
5 to 10 in. (127 to 254 mm) 4 in. (100 mm) Minimum Width
iron soil pipe and fittings.
1
12 to 15 in. (305 to 381 mm) 5 ⁄2 in. (140 mm) Minimum Width
1.2 Couplings covered by this standard shall have minimum
dimensions as found in Table 1 and Fig. 1 of this standard.
1.3 The values stated in inch-pound units are to be regarded
C564 Specification for Rubber Gaskets for Cast Iron Soil
as standard. The values given in parentheses are mathematical
Pipe and Fittings
conversions to SI units that are provided for information only
2.2 CISPI Standards:
and are not considered standard.
CISPI-301 SpecificationforHublessCastIronSoilPipeand
1.4 The committee with jurisdiction over this standard is
Fittings for Sanitary and Storm Drain, Waste and Vent
aware of comparable standards published by other organiza-
Piping Applications
tions, namely Cast Iron Soil Pipe Institute specification CISPI
CISPI-310 Specification for coupling for use in Connection
310 and Factory Mutual Research standard FM 1680.
with Hubless Cast Iron Soil Pipe and Fittings for Sanitary
1.5 The following precautionary caveat pertains only to the
and Storm Drain, Waste and Vent Piping Applications
test method portion, Section 7, of this specification. This
FM 1680 Approval Standard Couplings used in Hubless
standard does not purport to address all of the safety concerns,
CastIronSystemsforDrain,WasteorVentSystemsabove
if any, associated with its use. It is the responsibility of the user
or below ground Industrial, Commercial, and Residential
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
3. Terminology
tions prior to use.
3.1 Definitions:
3.1.1 Definitions of the following terms used in this speci-
2. Referenced Documents
fication are found in Terminology A644.
2
2.1 ASTM Standards:
3.2 Definitions of Terms Specific to This Standard:
A240/A240M Specification for Chromium and Chromium-
3.2.1 center stop, n—an integral part of the gasket centered
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
on the axial length of the gasket intended to limit the insertion
Vessels and for General Applications
depth of the pipe to be coupled.
A493 Specification for Stainless Steel Wire and Wire Rods
3.2.2 clamp assembly, n—that portion of the coupling
for Cold Heading and Cold Forging
excluding the gasket.
A644 Terminology Relating to Iron Castings
3.2.3 coupling, n—the complete assembly.
A888 Specification for Hubless Cast Iron Soil Pipe and
3.2.4 fitting, n—parts of a pipeline other than straight pipes,
Fittings for Sanitary and Storm Drain, Waste, and Vent
valves, or couplings.
Piping Applications
3.2.5 gasket, n—the elastomeric portion of the coupling.
3.2.6 heavy duty coupling, n—a shielded coupling that has
dimensions not less than those detailed in Table 1 and Fig. 1.
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
3.2.7 joint, n—the point of assembly consisting of the
Castings and is the direct responsibility of Subcommittee A04.75 on Gaskets and
coupling and the joined pipes or fittings, or both.
Coupling for Plumbing and Sewer Piping.
3.2.8 shield, n—an external metallic protective device de-
Current edition approved Oct. 15, 2009. Published December 2009. Originally
signed to protect the sealing gasket from external elements that
approved in 2002. Last previous edition approved in 2009 as C1540 – 09. DOI:
10.1520/C1540-09a.
could cause failure of the sealing assembly.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.2.9 coupling manufacturer, n—the entity that attaches the
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
coupling assembly to the shield of the couplings covered by
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. this standard specification.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1540 – 09a
FIG. 1 Typical Center Stop Detail
3.2.10 gasket manufac
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1540–09 Designation: C1540 – 09a
Standard Specification for
Heavy Duty Shielded Couplings Joining Hubless Cast Iron
1
Soil Pipe and Fittings
This standard is issued under the fixed designation C1540; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the evaluating of the performance of heavy duty shielded couplings to join hubless cast iron soil
pipe and fittings.
1.2 Couplings covered by this standard shall have minimum dimensions as found in Table 1 and Fig. 1 of this standard.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of comparable standards published by other organizations,
namely Cast Iron Soil Pipe Institute specification CISPI 310 and Factory Mutual Research standard FM 1680.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels
and for General Applications
A493 Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
A644 Terminology Relating to Iron Castings
A888 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping
Applications
C564 Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
2.2 CISPI Standards:
CISPI-301 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping
Applications
CISPI-310 SpecificationforcouplingforuseinConnectionwithHublessCastIronSoilPipeandFittingsforSanitaryandStorm
Drain, Waste and Vent Piping Applications
FM 1680 Approval Standard Couplings used in Hubless Cast Iron Systems for Drain, Waste or Vent Systems above or below
ground Industrial, Commercial, and Residential
3. Terminology
3.1 Definitions:
3.1.1 Definitions of the following terms used in this specification are found in Terminology A644.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 center stop, n—anintegralpartofthegasketcenteredontheaxiallengthofthegasketintendedtolimittheinsertiondepth
of the pipe to be coupled.
3.2.2 clamp assembly, n—that portion of the coupling excluding the gasket.
3.2.3 coupling, n—the complete assembly.
3.2.4 fitting, n—parts of a pipeline other than straight pipes, valves, or couplings.
1
This specification is under the jurisdiction ofASTM CommitteeA04 on Iron Castings and is the direct responsibility of SubcommitteeA04.75 on Gaskets and Coupling
for Plumbing and Sewer Piping.
Current edition approved Sept. 1,Oct. 15, 2009. Published SeptemberDecember 2009. Originally approved in 2002. Last previous edition approved in 20082009 as
C1540 – 089. DOI: 10.1520/C1540-09a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1540 – 09a
TABLE 1
Nominal Pipe Size Coupling Width
1
1 ⁄2 to 4 in. (38 to 100 mm) 3 in. (76 mm) Minimum Width
5 to 10 in. (127 to 254 mm) 4 in. (100 mm) Minimum Width
1
12 to 15 in. (305 to 381 mm) 5 ⁄2 in. (140 mm) Minimum Width
FIG. 1 Typical Center Stop Detail
3.2.5 gasket, n—the elastomeric portion of the coupling.
3.2.6 heavy duty coupling, n—a shielded coupling that has dimensions not less than those detailed in Table 1 and Fig. 1.
3.2.7 joint, n—the point of assembly consisting of the coupling and the joined pipes or fittings, or both.
3.2.8 shield, n—an external metallic protective device
...