ASTM F628-08
(Specification)Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core
ABSTRACT
This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core. The ABS plastics used to make the pipes shall only be either virgin or reworked as specfieid. Reprocessed or recycled plastics are excluded from this specification. The pipes shall meet specified requirements for dimension such as outside diameter, wall thickness, and length; and for performance such as pipe stiffness, lower confidence limit, flattening resistance, impact strength, bond strength, pigments or screening agents, and solvent cement.
SCOPE
1.1 This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid ABS layers and the core consisting of closed-cell cellular ABS. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers.
1.2 Fittings suitable for use with pipe meeting the requirements of this specification are given in Annex A1. Fittings meeting the requirement of Specification D 2661 are also acceptable.
1.3 Acrylonitrile-butadiene-styrene plastic which does not meet the definitions of virgin ABS plastic as given in 3.2.4 is excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic which meets the requirements of rework plastic as given in 5.3 is acceptable.
1.4 Reprocessed plastic or recycled plastic as defined in Terminology D 883 is excluded.
1.5 Recommendations for storage, joining, and installation are provided in Appendixes X1, X2, and X3, respectively.
1.6 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.7 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F628 −08 AnAmerican National Standard
Standard Specification for
Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic
1
Drain, Waste, and Vent Pipe With a Cellular Core
ThisstandardisissuedunderthefixeddesignationF628;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
1.1 This specification covers coextruded acrylonitrile-
2
D1898Practice for Sampling of Plastics (Withdrawn 1998)
butadiene-styrene (ABS) plastic drain, waste, and vent pipe
D2122Test Method for Determining Dimensions of Ther-
made to Schedule 40 iron pipe sizes (IPS) and produced by the
moplastic Pipe and Fittings
coextrusion process with concentric inner and outer solidABS
D2235Specification for Solvent Cement for Acrylonitrile-
layers and the core consisting of closed-cell cellular ABS.
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
Plasticwhichdoesnotmeetthematerialrequirementsspecified
D2321PracticeforUndergroundInstallationofThermoplas-
in Section 5 is excluded from single layer and all coextruded
tic Pipe for Sewers and Other Gravity-Flow Applications
layers.
D2412Test Method for Determination of External Loading
1.2 Fittings suitable for use with pipe meeting the require-
Characteristics of Plastic Pipe by Parallel-Plate Loading
ments of this specification are given in Annex A1. Fittings
D2444Test Method for Determination of the Impact Resis-
meeting the requirement of Specification D2661 are also
tance of Thermoplastic Pipe and Fittings by Means of a
acceptable.
Tup (Falling Weight)
1.3 Acrylonitrile-butadiene-styrene plastic which does not D2661 Specification for Acrylonitrile-Butadiene-Styrene
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
meet the definitions of virgin ABS plastic as given in 3.2.4 is
excluded, as performance of plastic other than those defined as and Fittings
D3311Specification for Drain, Waste, and Vent (DWV)
virgin was not determined. ABS rework plastic which meets
therequirementsofreworkplasticasgivenin5.3isacceptable. Plastic Fittings Patterns
D3965ClassificationSystemandBasisforSpecificationsfor
1.4 Reprocessed plastic or recycled plastic as defined in
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials
Terminology D883 is excluded.
for Pipe and Fittings
1.5 Recommendations for storage, joining, and installation
E105Practice for Probability Sampling of Materials
are provided in Appendixes X1, X2, and X3, respectively.
E122PracticeforCalculatingSampleSizetoEstimate,With
Specified Precision, the Average for a Characteristic of a
1.6 Thetextofthisspecificationreferencesnotes,footnotes,
Lot or Process
and appendixes which provide explanatory material. These
F402 Practice for Safe Handling of Solvent Cements,
notesandfootnotes(excludingthoseintablesandfigures)shall
Primers, and Cleaners Used for Joining Thermoplastic
not be considered as requirements of the specification.
Pipe and Fittings
1.7 The values stated in inch-pound units are to be regarded
F412Terminology Relating to Plastic Piping Systems
as the standard. The values given in parentheses are for
F1498SpecificationforTaperPipeThreads60°forThermo-
information only.
plastic Pipe and Fittings
2.2 Federal Standard:
2. Referenced Documents
3
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
2.1 ASTM Standards:
2.3 Military Standard:
D618Practice for Conditioning Plastics for Testing
3
MIL-STD-129Marking for Shipment and Storage
D883Terminology Relating to Plastics
1 2
This specification is under the jurisdiction ofASTM Committee F17 on Plastic The last approved version of this historical standard is referenced on
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. www.astm.org.
3
Current edition approved May 1, 2008. Published May 2008. Originally Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
ε1
approved in 1979. Last previous edition approved in 2006 as F628–06 . DOI: Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
10.1520/F0628-08. www.dodssp.daps.mil.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F628−08
NOTE 2—This specification does not include requirements for pipe
3. Terminology
intended to be used to vent combustion gases.
3.1 Definitions:
3.1.1 Definitions are in accordance withTerminology F412,
5. Materials
and abbreviations are in accordance with Terminology D1600,
5.1 Material Specification—Virgin ABS plastic shall con-
unless otherwise sp
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
e1
Designation:F 628–06 Designation: F 628 – 08
Standard Specification for
Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic
1
Drain, Waste, and Vent Pipe With a Cellular Core
This standard is issued under the fixed designation F 628; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Table2 was editorially corrected in May 2007.
1. Scope*
1.1 This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe made to
Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solidABS layers and
the core consisting of closed-cell cellular ABS. Plastic which does not meet the material requirements specified in Section 5 is
excluded from single layer and all coextruded layers.
1.2 Fittings suitable for use with pipe meeting the requirements of this specification are given in Annex A1. Fittings meeting
the requirement of Specification D2661 are also acceptable.
1.3 Acrylonitrile-butadiene-styrene plastic which does not meet the definitions of virgin ABS plastic as given in 3.2.4 is
excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic which meets the
requirements of rework plastic as given in 5.3 is acceptable.
1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded.
1.5 Recommendations for storage, joining, and installation are provided in Appendixes X1, X2, and X3, respectively.
1.6 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.7 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesesareforinformation
only.
2. Referenced Documents
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
2
D1898 Practice for Sampling of Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falling
Weight)
D2661 Specification forAcrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
E105 Practice for Probability Sampling Of Materials
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, theAverage for a Characteristic of a Lot or
Process
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved June 1, 2006. Published June 2006. Originally approved in 1979. Last previous edition approved in 2001 as F628–01.
e1
Current edition approved May 1, 2008. Published May 2008. Originally approved in 1979. Last previous edition approved in 2006 as F628–06 .
2
Withdrawn
2
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 628–08
F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings
2.2 Federal Standard:
3
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
3
MIL-STD-129 Marking for Shipment and Storage
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.