iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM G20-10(2019)

(Test Method)

Standard Test Method for Chemical Resistance of Pipeline Coatings

Standard Test Method for Chemical Resistance of Pipeline Coatings

SIGNIFICANCE AND USE
4.1 The data obtained for short-term tests are of interest only in eliminating the most unsuitable materials or for indicating a probable order of resistance in any particular media.  
4.2 Test conditions should take into account the manner and duration of immersion, the reagent, the temperature of the system, the area exposed above and below the liquid level, and other performance factors selected for the particular test.
SCOPE
1.1 This test method is intended for evaluating the resistance of pipe coating materials when exposed to various concentrations of reagents or suspected soil contaminants. The test serves as a guide to investigators wishing to compare the relative merits of pipe-coating materials in specific environments. The choice of reagents, concentrations, duration of immersion, temperature of test, and properties to be reported are necessarily arbitrary and should be chosen to reflect conditions known to exist along the pipeline right-of-way.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Sep-2019
ICS
87.040 - Paints and varnishes
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.48 - Durability of Pipeline Coating and Linings
Current Stage
Ref Project

Relations

Replaces
ASTM G20-10(2015) - Standard Test Method for Chemical Resistance of Pipeline Coatings
Effective Date
01-Oct-2019
Refers
ASTM G17-07(2020) - Standard Test Method for Penetration Resistance of Pipeline Coatings (Blunt Rod)
Effective Date
01-Aug-2020
Refers
ASTM D883-18 - Standard Terminology Relating to Plastics
Effective Date
01-Nov-2018
Refers
ASTM D883-17 - Standard Terminology Relating to Plastics
Effective Date
15-Aug-2017
Refers
ASTM D883-18a - Standard Terminology Relating to Plastics
Effective Date
01-Dec-2018
Refers
ASTM D883-19 - Standard Terminology Relating to Plastics
Effective Date
01-Feb-2019
Refers
ASTM D883-19a - Standard Terminology Relating to Plastics
Effective Date
15-Apr-2019
Refers
ASTM D883-19c - Standard Terminology Relating to Plastics
Effective Date
01-Aug-2019
Refers
ASTM D883-20 - Standard Terminology Relating to Plastics
Effective Date
01-Jan-2020
Referred By
ASTM A934/A934M-22 - Standard Specification for Epoxy-Coated Prefabricated Steel Reinforcing Bars
Effective Date
01-Oct-2019
Referred By
ASTM A972/A972M-00(2021) - Standard Specification for Fusion Bonded Epoxy-Coated Pipe Piles
Effective Date
01-Oct-2019
Referred By
ASTM A775/A775M-22 - Standard Specification for Epoxy-Coated Steel Reinforcing Bars
Effective Date
01-Oct-2019
Referred By
ASTM A1124/A1124M-23 - Standard Specification for Textured Epoxy-Coated Steel Reinforcing Bars
Effective Date
01-Oct-2019
Referred By
ASTM D3963/D3963M-21 - Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars
Effective Date
01-Oct-2019
Referred By
ASTM A950/A950M-11(2023) - Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
Effective Date
01-Oct-2019
Referred By
ASTM D6577-15(2019) - Standard Guide for Testing Industrial Protective Coatings
Effective Date
01-Oct-2019
Referred By
ASTM A882/A882M-20 - Standard Specification for Filled Epoxy-Coated Seven-Wire Steel Prestressing Strand
Effective Date
01-Oct-2019
Referred By
ASTM A1055/A1055M-22 - Standard Specification for Zinc and Epoxy Dual-Coated Steel Reinforcing Bars
Effective Date
01-Oct-2019

Buy Standard

ASTM G20-10(2019) - Standard Test Method for Chemical Resistance of Pipeline CoatingsASTM G20-10(2019) - Standard Test Method for Chemical Resistance of Pipeline Coatings
PreviousNext
Standard
ASTM G20-10(2019) - Standard Test Method for Chemical Resistance of Pipeline Coatings
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: G20 − 10 (Reapproved 2019)
Standard Test Method for
1
Chemical Resistance of Pipeline Coatings
This standard is issued under the fixed designation G20; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Thickness of Pipeline Coatings on Steel (Withdrawn
3
2013)
1.1 This test method is intended for evaluating the resis-
G17 Test Method for Penetration Resistance of Pipeline
tance of pipe coating materials when exposed to various
Coatings (Blunt Rod)
concentrations of reagents or suspected soil contaminants. The
test serves as a guide to investigators wishing to compare the
3. Summary of Test Method
relative merits of pipe-coating materials in specific environ-
3.1 This test method consists of an immersion-type test in a
ments. The choice of reagents, concentrations, duration of
closed container where coated pipe specimens are in long-term
immersion, temperature of test, and properties to be reported
contactwithboththeliquidandvaporphaseofthetestreagent.
are necessarily arbitrary and should be chosen to reflect
Specimens exposed in this manner are inspected for visible
conditions known to exist along the pipeline right-of-way.
signs of chemical attack. Subsequent tests for cathodic dis-
1.2 The values stated in SI units are to be regarded as the
bonding in accordance with Test Method G8, or penetration
standard. The values given in parentheses are for information
under load in accordance with Test Method G17, may be
only.
applied to determine if the specimens have undergone any loss
1.3 This standard does not purport to address all of the
of mechanical or bonding properties.
safety concerns, if any, associated with its use. It is the
4. Significance and Use
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
4.1 The data obtained for short-term tests are of interest
mine the applicability of regulatory limitations prior to use.
only in eliminating the most unsuitable materials or for
1.4 This international standard was developed in accor-
indicating a probable order of resistance in any particular
dance with internationally recognized principles on standard-
media.
ization established in the Decision on Principles for the
4.2 Test conditions should take into account the manner and
Development of International Standards, Guides and Recom-
duration of immersion, the reagent, the temperature of the
mendations issued by the World Trade Organization Technical
system, the area exposed above and below the liquid level, and
Barriers to Trade (TBT) Committee.
other performance factors selected for the particular test.
2. Referenced Documents
5. Apparatus
2
2.1 ASTM Standards:
5.1 Thickness Gage, capable of measuring the coating
D543 Practices for Evaluating the Resistance of Plastics to
thickness in the manner prescribed by Test Method G12.
Chemical Reagents
5.2 Test Container—Atransparent closed container, sized to
D883 Terminology Relating to Plastics
completely encase the pipe specimen and large enough to
G8 Test Methods for Cathodic Disbonding of Pipeline Coat-
provide adequate exposure to both the liquid and vapor states
ings
of reagent.
G12 Test Method for Nondestructive Measurement of Film
NOTE 1—For example, a 2-L (2.0-qt) capacity, Mason-type jar with a
70-mm (2.75-in.) diameter neck has been found suitable for use with 2 in.
pipe and is illustrated in Fig. 1.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
5.2.1 To avoid pressure build-up within the test containers,
Subcommittee D01.48 on Durability of Pipeline Coating and Linings.
the threaded cup shall be replaced with a solid-rubber stopper.
Current edition approved Oct. 1, 2019. Published October 2019. Originally
A positive venting device, such as a water seal, shall be used
approved in 1971. Last previous edition approved in 2015 as G20 – 10(2015). DOI:
10.1520/G0020-10R19. when testing with volatile solvents at elevated temperatures.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 10
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D16-23(Terminology)
Standard Terminology for Paint, Related Coatings, Materials, and Applications

SCOPE
1.1 This standard consists of technical terms used in standards under the jurisdiction of ASTM Committee D01 (on Paint and Related Coatings, Materials, and Applications), and of definitions suitable for use in these standards.
Note 1: When any definition in this standards is quoted or published out of the context of this standard, editorially insert the following delimiting statement “for paints and related coatings, materials, and applications” after the dash following the term (in the absence of an existing delimiting statement). This will limit the filed of application of the term and definition to that approved by this committee.  
1.2 In this terminology standard, definitions used in other ASTM standards are indicated by following the definition with the designation of that standard. In some cases, a relevant D01 subcommittee is also listed. Definitions influenced by those used by other organizations are indicated by the acronym of the organization. Primary terms are given in bold, while narrower and unapproved terms are given in italics.  
1.3 There are several specialized terminology standards under the jurisdiction of Committee D01, as follows: D804, D1695, D6440, D6488, and D7188. Few definitions from those standards are included in Terminology D16. Therefore, in searches for definitions of paints and coatings terms, these standards should be included where appropriate.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D2805-11(2023)(Test Method)
Standard Test Method for Hiding Power of Paints by Reflectometry

SIGNIFICANCE AND USE
5.1 This is a precise instrumental method giving results having an absolute physical significance without reference to a comparison paint. It should be used when maximum precision and minimum subjectivity are required, as in testing specification coatings or evaluating the hiding efficiency of pigments.  
5.2 Hiding power Test Method D344 is visual instead of instrumental, and gives results that are relative to a material standard instead of absolute. It is less precise than Test Method D2805 but more closely aligned with practical painting procedures.
SCOPE
1.1 This test method covers the determination, without reference to a material paint standard, of the hiding power of air dry coatings with Y tristimulus values greater than 15 %. With appropriate modification, it can also be used to test baking finishes.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1644-01(2023)(Test Method)
Standard Test Methods for Nonvolatile Content of Varnishes

SIGNIFICANCE AND USE
2.1 These test methods are applicable to varnish and are useful to producers and users in determining nonvolatile content and are sometimes an appropriate measure of the film-forming matter in varnish.
SCOPE
1.1 These test methods determine the fraction of a varnish that is nonvolatile at the temperature of the test while volatile solvents are driven off. It is sometimes an approximate measure of the film-forming matter in a varnish.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific statement, see Section 3.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3322-23(Practice)
Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal

SIGNIFICANCE AND USE
4.1 Primers and primer surfacers may be used over many different surfaces top coated with one or more of a variety of coatings and subjected to many kinds of wear and exposure.  
4.2 The selection of the tests to be used for any given product or system must be governed by experience and by the requirement agreed upon between the producer and the user.
SCOPE
1.1 This practice covers the selection and use of procedures for testing primers and primer surfacers.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6486-23(Practice)
Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings

SIGNIFICANCE AND USE
4.1 Since the exposure of automotive coatings to the various mechanical and chemical stresses encountered in actual operations, is very opportunistic, obtaining statistically significant data from which valid conclusions can be drawn, requires rigorous attention to the experimental designs and conditions of exposure.
SCOPE
1.1 This practice covers the protocol for vehicle service exposure testing of automotive coatings. Such exposure testing is valuable for the verification of the performance of automotive coatings and correlation with laboratory test data. Vehicle service exposure is intended to provide short term (2 to 20 weeks) exposure to the stress factors associated with vehicle operation. Factors included are scratch, mar, impact, stone chipping, insect impact, bird dropping, tree sap and staining, environmental fallout, etc.
Note 1: Vehicle service exposure is not intended to provide the conditions that are needed for characterizing the long term effects of weathering or corrosion exposure.  
1.2 The exposure conditions are produced by the placement of multiple test panels of automotive finishes on automotive test fleets that traverse a defined road course. Exposure to the operating environment can be 20 h/day, 7 days/week allowing for accumulation of over 100 000 miles in 10 weeks of exposure.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6762-18(2023)(Test Method)
Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings

SIGNIFICANCE AND USE
5.1 This test method determines hiding power of a test paint by visual evaluation of a spray applied coating.
Note 1: Test Method D2805 describes an instrumental method for determining hiding power. The paint film is applied at a uniform thickness (for example with a doctor blade), the film thickness is measured rigorously, and the opacity is determined photometrically. Hiding power is thereby determined with a high degree of precision.  
5.2 Test Method D6762 is less precise than Test Method D2805, but is commonly used since it is more closely related to the application characteristics of the paint and is simpler in concept and evaluation.
SCOPE
1.1 This test method provides for the quantitative visual determination of the film thickness required to achieve full hiding. This film thickness is considered to be the hiding power of a test paint.  
1.2 This method applies only to spray applied coatings but its concepts are valid for other methods of application as well.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3732-23(Practice)
Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings

SIGNIFICANCE AND USE
4.1 This practice provides a guide whereby all pertinent variables relating to the ultraviolet cure of a coating are described.
SCOPE
1.1 This practice applies to all coatings cured by ultraviolet energy.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D713-23(Practice)
Standard Practice for Conducting Road Service Tests on Fluid Traffic Marking Materials

SIGNIFICANCE AND USE
3.1 This practice is an accelerated evaluation of bead retention, retroreflectivity, daytime color, night time color, and wear characteristics of fluid traffic marking materials. It is used to determine the useful life of such markings in the field. The same procedures are applicable to evaluating longitudinal lines to determine service life.
SCOPE
1.1 This practice covers the determination of the relative service life of fluid traffic marking materials such as paint, thermoplastic, epoxy, and polyester products under actual road conditions using transverse test lines. Materials under test are applied under prescribed conditions and periodic observations are made using prescribed performance criteria.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5682-18(2023)(Test Method)
Standard Test Methods for Electrical Resistivity of Liquid Paint and Related Materials

SIGNIFICANCE AND USE
4.1 These tests are suitable for testing paints adjusted for compatibility with various electrostatic spray coating applications, and by their use, spray performance can be optimized.
SCOPE
1.1 These test methods cover the determination of specific resistance (resistivity) of liquid paints, solvents, and other fluids in the range of 0.6 to 2640 MΩ-cm.  
1.2 Test Method A describes a procedure for making resistance tests with a commonly used paint application test assembly (Fig. 1 and Fig. 2).
FIG. 1 Analog Paint Application Test Assembly  
FIG. 2 Diagram of Digital Application Test Assembly  
1.3 Test Method B describes a procedure for making resistance tests with a conductivity meter (Fig. 3).
FIG. 3 Conductivity Meter  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3891-23(Practice)
Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products

SIGNIFICANCE AND USE
3.1 The procedures described in this practice are designed to provide uniform glass panels for testing of paint, varnish, lacquer, conversion coatings and related products.
SCOPE
1.1 This practice covers the preparation of glass panels for subsequent testing of paint, varnish, lacquer, and related products.2  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off