ASTM C1559-04(2009)
(Test Method)Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type)
Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type)
SIGNIFICANCE AND USE
The tendency of the insulation toward wicking can result in an increase in weight and a resultant potential degradation in the properties of the insulation.
SCOPE
1.1 This test method covers a laboratory procedure for evaluating the tendency of, aircraft type, fibrous glass blanket insulation to wick water.
1.2 The wicking characteristics of materials may be affected by environmental conditions such as temperature and humidity. Values obtained as a result of this test method may not adequately describe the wicking characteristics of materials subject to conditions other than those indicated in the test method. (See Specification C 800.)
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1559 − 04(Reapproved 2009)
Standard Test Method for
Determining Wicking of Fibrous Glass Blanket Insulation
(Aircraft Type)
This standard is issued under the fixed designation C1559; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 wicking—the infiltration of a wetting liquid into a
fibrous glass blanket by capillary attraction.
1.1 This test method covers a laboratory procedure for
evaluating the tendency of, aircraft type, fibrous glass blanket
4. Summary of Test Method
insulation to wick water.
4.1 The insulation is suspended in de-ionized or distilled
1.2 The wicking characteristics of materials may be affected
water so that the bottom of the specimen is submerged to one
byenvironmentalconditionssuchastemperatureandhumidity.
inch below the water surface; distance of wicking is noted
Values obtained as a result of this test method may not
every 24 h for 96 h and then again at the end of 168 h.
adequately describe the wicking characteristics of materials
subject to conditions other than those indicated in the test
5. Significance and Use
method. (See Specification C800.)
1.3 The values stated in inch-pound units are to be regarded 5.1 The tendency of the insulation toward wicking can
as standard. The values given in parentheses are mathematical
result in an increase in weight and a resultant potential
conversions to SI units that are provided for information only degradation in the properties of the insulation.
and are not considered standard.
6. Apparatus
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
6.1 As described in the Procedure section of this test
responsibility of the user of this standard to establish appro-
method.
priate safety and health practices and determine the applica-
6.2 Steel Rule, accurate to 6 0.05 in. (1 mm).
bility of regulatory limitations prior to use.
2. Referenced Documents
7. Sampling, Test Specimens, and Test Units
2.1 ASTM Standards:
7.1 Six specimens shall be tested for each procedure, cut
C168 Terminology Relating to Thermal Insulation
with the axis parallel to the length and six cut with the axis
C390 Practice for Sampling and Acceptance of Thermal
perpendicular to the length from a representative package.(See
Insulation Lots
Practice C390.)
C800 Specification for Fibrous Glass Blanket Insulation
7.2 The specimens shall be 1- by 6-in. (25.4- by 152.4-mm)
(Aircraft Type)
by full sample thickness.
E691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method
7.3 The insulation shall be tested without facing or jacket-
ing.
3. Terminology
3.1 Definitions—Terminology C168 shall be considered as
8. Conditioning
applying to the terms used in this specification.
8.1 As described in the Procedure section of this test
ThistestmethodisunderthejurisdictionofASTMCommitteeC16onThermal
method.
Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation
Finishes and Moisture.
9. Procedure A—Wicking as Received
Current edition approved May 1, 2009. Published August 2009. Originally
approved in 2003. Last previous edition approved in 2004 as C1559 – 04. DOI:
9.1 Condition specimens for at least 24 h at 73 6 4°F (23 6
10.1520/C1559-04R09.
2°C) and 50 6 5 % relative humidity.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
9.2 With fine wire, fasten loosely six specimens (three cut
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. with the axis parallel to the length and three cut with the axis
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C1559 − 04 (2009)
the water. Ratio of specimen to water shall not be less than 1
to 100 by weight.Acontinuous flow of water shall be supplied
to the bottom of the container at the above temperature at a rate
of five changes per hour.At the end of the leaching period, the
specimen shall be removed from the water, air dried to a
constant weight and weighed. The leached specimen shall be
tested according to procedure outlined in 9.2-9.5.
12. Calculation or Interpretation of Results
12.1 Determine the amount of wicking by measurement
with a steel rule as described in 6.2.
12.2 Wetting of the submerged portion of the wicking
specimens is permissible. Wicking is the distance of wetting
above the water surface (average value of center-point mea-
surements of three sides of the wicking specimen-side adjacent
to screen surface should not be measured).
FIG. 1 Typical Specimen Mounting for Wicking Test
12.3 Beadsofwaterarenottobeconstruedasaconditionof
3 wetting. The formation of beads of water on the insulation
perpendicular to the length) to a grease-free 0.025 to 0.035 in.
surface indicates water repellency.
(0.64 to 0.89 mm) 8
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1559–03 Designation:C1559–04 (Reapproved 2009)
Standard Test Method for
Determining Wicking of Glass FiberFibrous Glass Blanket
Insulation (Aircraft Type)
This standard is issued under the fixed designation C 1559; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1This test method covers a laboratory procedure for evaluating the tendency of, aircraft type, glass fiber blanket insulation to
wick water.
1.2The wicking characteristics of materials may be affected by environmental conditions such as temperature and humidity.
Values obtained as a result of this test method may not adequately describe the wicking characteristics of materials subject to
conditions other than those indicated in the test method.
1.3
1.1 This test method covers a laboratory procedure for evaluating the tendency of, aircraft type, fibrous glass blanket insulation
to wick water.
1.2 The wicking characteristics of materials may be affected by environmental conditions such as temperature and humidity.
Values obtained as a result of this test method may not adequately describe the wicking characteristics of materials subject to
conditions other than those indicated in the test method. (See Specification C 800.)
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
C 168 Terminology Relating to Thermal Insulating Materials
C390Criteria for Sampling and Acceptance of Preformed Insulation Lots
C800Specification for Glass Fiber Blanket Insulation (Aircraft Type) Terminology Relating to Thermal Insulation
C 390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C 800 Specification for Fibrous Glass Blanket Insulation (Aircraft Type)
E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3. Terminology
3.1 Definitions—Terminology C 168 shall be considered as applying to the terms used in this specification.
3.1.1 wicking—the infiltration of a wetting liquid into a glass fiberfibrous glass blanket by capillary attraction.
4. Summary of Test Method
4.1 The insulation is suspended in de-ionized or distilled water so that the bottom of the specimen is submerged to one inch
below the water surface; distance of wicking is noted every 24 h for 96 h and then again at the end of 168 h.
5. Significance and Use
5.1 The tendency of the insulation toward wicking can result in an increase in weight and a resultant potential degradation in
the properties of the insulation.
This test method is under the jurisdiction ofASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation Finishes
and Moisture.
Current edition approved June 10, 2003. Published August 2003.
Current edition approved May 1, 2009. Published August 2009. Originally approved in 2003. Last previous edition approved in 2004 as C1559 – 04.
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 04.06.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
C1559–04 (2009)
6. Apparatus
6.1 As described in the Procedure section of this test method.
6.2 Steel Rule, accurate to 6 0.05 in. (1 mm).
7. Sampling, Test Specimens, and Test Units
7.1 Six specimens shall be tested for each procedure, cut with the axis parallel to the length and six cut with the axis
perpendicular to the length from a representative package.(See Practice C 390.)
7.2 The specimens shall be 1- by 6-in. (25.4- by 152.4-mm) by full sample thickness.
7.3 The insulation shall be tested without facing or jacketing.
8. Conditioning
8.1 As described in the Procedure section of this test method.
9. Procedure A—Wicking as Received
9.1 Condition specimens for at least 24 h at 73 6 4°F (23 6 2°C) and 50 6 5 % relative humidity.
9.2 With fine wire, fasten loosely six specimens (three cut with the axis parallel to the length and three cut with the axis
perpendicular to the length) to a grease-free 0.025 to 0.035 in. (0.64 to 0.89 mm) 8 by 8 mesh stainless steel wire screen. Position
this assembly in an upright position so the ends of the specimens touch the bottom of the container. The 6-in. sample dimension
is in a perpendicular direction to the water surface. The specimens must not touch each other or the sides of the container (Fig.
1).
9.3 Pour de-ionized (or distilled) water into the container to a height of 1-in. (25-mm) (Optional: add dye to the water—1 to
2 drops per liter to the water to facilitate marking the extent of wicking). The water shall be at 68 6 4°F (20 6 2°C).
9.4 Position the remaining
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1559–04 Designation:C1559–04 (Reapproved 2009)
Standard Test Method for
Determining Wicking of Fibrous Glass Blanket Insulation
(Aircraft Type)
This standard is issued under the fixed designation C 1559; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers a laboratory procedure for evaluating the tendency of, aircraft type, fibrous glass blanket insulation
to wick water.
1.2 The wicking characteristics of materials may be affected by environmental conditions such as temperature and humidity.
Values obtained as a result of this test method may not adequately describe the wicking characteristics of materials subject to
conditions other than those indicated in the test method. (See Specification C 800.)
1.3
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
C 168 Terminology Relating to Thermal Insulation
C 390 Practice for Sampling and Acceptance of PreformedThermal Insulation Lots
C 800 Specification for Fibrous Glass Blanket Insulation (Aircraft Type) Specification for Fibrous Glass Blanket Insulation
(Aircraft Type)
E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3. Terminology
3.1 Definitions—Terminology C 168 shall be considered as applying to the terms used in this specification.
3.1.1 wicking—the infiltration of a wetting liquid into a fibrous glass blanket by capillary attraction.
4. Summary of Test Method
4.1 The insulation is suspended in de-ionized or distilled water so that the bottom of the specimen is submerged to one inch
below the water surface; distance of wicking is noted every 24 h for 96 h and then again at the end of 168 h.
5. Significance and Use
5.1 The tendency of the insulation toward wicking can result in an increase in weight and a resultant potential degradation in
the properties of the insulation.
6. Apparatus
6.1 As described in the Procedure section of this test method.
6.2 Steel Rule, accurate to 6 0.05 in. (1 mm).
7. Sampling, Test Specimens, and Test Units
7.1 Six specimens shall be tested for each procedure, cut with the axis parallel to the length and six cut with the axis
This test method is under the jurisdiction ofASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation Finishes
and Moisture.
Current edition approved Sept. 1. 2004. Published October 2004. Originally approved in 2003. Last previous edition approved in 2003 as C1559–03.
Current edition approved May 1, 2009. Published August 2009. Originally approved in 2003. Last previous edition approved in 2004 as C1559 – 04.
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
C1559–04 (2009)
perpendicular to the length from a representative package.(See Practice C 390.)
7.2 The specimens shall be 1- by 6-in. (25.4- by 152.4-mm) by full sample thickness.
7.3 The insulation shall be tested without facing or jacketing.
8. Conditioning
8.1 As described in the Procedure section of this test method.
9. Procedure A—Wicking as Received
9.1 Condition specimens for at least 24 h at 73 6 4°F (23 6 2°C) and 50 6 5 % relative humidity.
9.2 With fine wire, fasten loosely six specimens (three cut with the axis parallel to the length and three cut with the axis
perpendicular to the length) to a grease-free 0.025 to 0.035 in. (0.64 to 0.89 mm) 8 by 8 mesh stainless steel wire screen. Position
this assembly in an upright position so the ends of the specimens touch the bottom of the container. The 6-in. sample dimension
is in a perpendicular direction to the water surface. The specimens must not touch each other or the sides of the container (Fig.
1).
9.3 Pour de-ionized (or distilled) water into the container to a height of 1-in. (25-mm) (Optional: add dye to the water—1 to
2 drops per liter to the water to facilitate marking the extent of wicking). The water shall be at 68 6 4°F (20 6 2°C).
9.4 Position the remaining six specimens similarly in another container. Pour de-ionized (or distilled) water into this container
to a height of 1-in. (25-mm), again adding dye. Maintain the temperature of this water at 120 6 5°F (50 6 2°C) by using a ho
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.