ASTM D2700-16a
(Test Method)Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
SIGNIFICANCE AND USE
5.1 Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation.
5.2 Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of fuels and engines.
5.2.1 Empirical correlations that permit calculation of automotive antiknock performance are based on the general equation:
Values of k1, k2, and k3 vary with vehicles and vehicle populations and are based on road-octane number determinations.
5.2.2 Motor O.N., in conjunction with Research O.N., defines the antiknock index of automotive spark-ignition engine fuels, in accordance with Specification D4814. The antiknock index of a fuel approximates the road octane ratings for many vehicles, is posted on retail dispensing pumps in the United States, and is referred to in vehicle manuals.
This is more commonly presented as:
5.3 Motor O.N. is used for measuring the antiknock performance of spark-ignition engine fuels that contain oxygenates.
5.4 Motor O.N. is important in relation to the specifications for spark-ignition engine fuels used in stationary and other nonautomotive engine applications.
5.5 Motor O.N. is utilized to determine, by correlation equation, the Aviation method O.N. or performance number (lean-mixture aviation rating) of aviation spark-ignition engine fuel.7
SCOPE
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested in a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend that matches the knock intensity of the sample fuel establishes the Motor octane number.
1.2 The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40 to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor octane number range.
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For more specific hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2700 − 16a
Designation: 236/87
Standard Test Method for
1
Motor Octane Number of Spark-Ignition Engine Fuel
This standard is issued under the fixed designation D2700; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This laboratory test method covers the quantitative
responsibility of the user of this standard to establish appro-
determination of the knock rating of liquid spark-ignition
priate safety and health practices and determine the applica-
engine fuel in terms of Motor octane number, including fuels
bility of regulatory limitations prior to use. For more specific
that contain up to 25 % v/v of ethanol. However, this test
hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex
method may not be applicable to fuel and fuel components that
2 A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1,
are primarily oxygenates. The sample fuel is tested in a
X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.
standardized single cylinder, four-stroke cycle, variable com-
pression ratio, carbureted, CFR engine run in accordance with
2. Referenced Documents
a defined set of operating conditions. The octane number scale
3
2.1 ASTM Standards:
is defined by the volumetric composition of primary reference
D1193 Specification for Reagent Water
fuel blends. The sample fuel knock intensity is compared to
D2268 Test Method for Analysis of High-Purity n-Heptane
that of one or more primary reference fuel blends. The octane
and Isooctane by Capillary Gas Chromatography
number of the primary reference fuel blend that matches the
D2360 Test Method for Trace Impurities in Monocyclic
knock intensity of the sample fuel establishes the Motor octane
Aromatic Hydrocarbons by Gas Chromatography (With-
number.
4
drawn 2016)
1.2 The octane number scale covers the range from 0 to 120
D2699 Test Method for Research Octane Number of Spark-
octane number, but this test method has a working range from
Ignition Engine Fuel
40 to 120 octane number. Typical commercial fuels produced
D2885 Test Method for Determination of Octane Number of
for automotive spark-ignition engines rate in the 80 to 90
Spark-Ignition Engine Fuels by On-Line Direct Compari-
Motor octane number range. Typical commercial fuels pro-
son Technique
duced for aviation spark-ignition engines rate in the 98 to 102
D3703 Test Method for Hydroperoxide Number of Aviation
Motor octane number range. Testing of gasoline blend stocks
Turbine Fuels, Gasoline and Diesel Fuels
orotherprocessstreammaterialscanproduceratingsatvarious
D4057 Practice for Manual Sampling of Petroleum and
levels throughout the Motor octane number range.
Petroleum Products
1.3 The values of operating conditions are stated in SI units
D4175 Terminology Relating to Petroleum Products, Liquid
and are considered standard. The values in parentheses are the
Fuels, and Lubricants
historical inch-pounds units. The standardized CFR engine
D4177 Practice for Automatic Sampling of Petroleum and
measurements continue to be in inch-pound units only because
Petroleum Products
oftheextensiveandexpensivetoolingthathasbeencreatedfor
D4814 Specification for Automotive Spark-Ignition Engine
this equipment.
Fuel
D5842 Practice for Sampling and Handling of Fuels for
Volatility Measurement
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Subcommittee D02.01 on Combustion Characteristics.
3
Current edition approved Dec. 1, 2016. Published January 2017. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1968. Last previous edition approved in 2016 as D2700 – 16. DOI: contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
10.1520/D2700-16A. Standards volume information, refer to the standard’s Document Summary page on
2
Researchoctanenumber,determinedusingTestMethodD2699,isacompanion the ASTM website.
4
method to provide a similar but typically higher octane rating under milder The last approved version of this historical standard is referenced on
operating conditions. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2700
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2700 − 16 D2700 − 16a
Designation: 236/87
Standard Test Method for
1
Motor Octane Number of Spark-Ignition Engine Fuel
This standard is issued under the fixed designation D2700; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel
in terms of Motor octane number, including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be
2
applicable to fuel and fuel components that are primarily oxygenates. The sample fuel is tested in a standardized single cylinder,
four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions.
The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock
intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend
that matches the knock intensity of the sample fuel establishes the Motor octane number.
1.2 The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40
to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane
number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number
range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor
octane number range.
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the
historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the
extensive and expensive tooling that has been created for this equipment.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For more specific hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6)
and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.
2. Referenced Documents
3
2.1 ASTM Standards:
D1193 Specification for Reagent Water
D2268 Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography
4
D2360 Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography (Withdrawn 2016)
D2699 Test Method for Research Octane Number of Spark-Ignition Engine Fuel
D2885 Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison
Technique
D3703 Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4175 Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.01 on Combustion Characteristics.
Current edition approved Jan. 1, 2016Dec. 1, 2016. Published February 2016January 2017. Originally approved in 1968. Last previous edition approved in 20142016 as
D2700 – 14.D2700 – 16. DOI: 10.1520/D2700-16.10.1520/D2700-16A.
2
Research octane number, determined using Test Method D2699, is a companion method to provide a similar but typically higher octane rating under milder operating
conditions.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.