ASTM A794/A794M-12
(Specification)Standard Specification for Commercial Steel (CS), Sheet, Carbon (0.16 % Maximum to 0.25 % Maximum), Cold-Rolled
Standard Specification for Commercial Steel (CS), Sheet, Carbon (0.16 % Maximum to 0.25 % Maximum), Cold-Rolled
ABSTRACT
This specification covers standard requirements for cold-rolled commercial steel sheet coils and cut lengths. The cast or heat analysis of the steel shall conform to the chemical requirements for carbon, manganese, phosphorus, and sulfur. Unspecified elements may be present. Limits on additional elements such as copper, nickel, chromium, molybdenum, vanadium, and columbium shall be stated. The material shall also conform to the required bending properties.
SCOPE
1.1 This specification covers cold-rolled commercial steel (CS) sheet in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and not over 0.25 %, and the maximum of the specified manganese range is not over 0.90 %. This material is ordered to chemical composition.
1.2 This specification is not applicable to the steels covered in Specifications A109/A109M and A1008/A1008M.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A794/A794M −12
Standard Specification for
Commercial Steel (CS), Sheet, Carbon (0.16% Maximum to
1
0.25% Maximum), Cold-Rolled
This standard is issued under the fixed designationA794/A794M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
3
1. Scope* 2.2 Society of Automotive Engineers Standard:
J 1086 Numbering Metals and Alloys
1.1 This specification covers cold-rolled commercial steel
(CS) sheet in coils and cut lengths, in which the maximum of
3. Ordering Information
the specified carbon range is over 0.15 and not over 0.25 %,
3.1 It is the purchaser’s responsibility to specify in the
and the maximum of the specified manganese range is not over
purchase order all ordering information necessary to purchase
0.90 %. This material is ordered to chemical composition.
theneededmaterial.Examplesofsuchinformation,includebut
1.2 This specification is not applicable to the steels covered
are not limited to, the following:
in Specifications A109/A109M and A1008/A1008M.
3.1.1 ASTM specification number and year of issue,
1.3 The values stated in either SI units or inch-pound units
3.1.2 Name of material (cold-rolled commercial steel (CS)
are to be regarded separately as standard. The values stated in
sheet),
each system may not be exact equivalents; therefore, each
3.1.3 Grade designation or chemical composition or both,
system shall be used independently of the other. Combining
3.1.4 Copper-bearing steel (if required),
values from the two systems may result in non-conformance
3.1.5 Finish; indicate unexposed with matte (dull) finish, or
with the standard.
exposed with either matte (dull), commercial bright or luster
finish, as required,
2. Referenced Documents
3.1.6 Specify oiled or not oiled, as required,
2
2.1 ASTM Standards:
3.1.7 Dimensions(thickness,width,andwhethercutlengths
A109/A109M Specification for Steel, Strip, Carbon (0.25 or coils),
Maximum Percent), Cold-Rolled
NOTE 1—Not all producers are capable of meeting all the limitations of
A568/A568M Specification for Steel, Sheet, Carbon,
the thickness tolerance tables in Specification A568/A568M. The pur-
Structural,andHigh-Strength,Low-Alloy,Hot-Rolledand
chaser should contact the producer regarding possible limitations prior to
placing an order.
Cold-Rolled, General Requirements for
A749/A749M Specification for Steel, Strip, Carbon and
3.1.8 Coil size (must include inside diameter, outside
High-Strength, Low-Alloy, Hot-Rolled, General Require-
diameter, and maximum mass),
ments for
3.1.9 Quantity,
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled,
3.1.10 Application (show part identification and
Carbon, Structural, High-Strength Low-Alloy, High-
description),
Strength Low-Alloy with Improved Formability, Solution
3.1.11 Cast or heat analysis report (request, if required), and
Hardened, and Bake Hardenable
3.1.12 Special requirements (if any).
E527 Practice for Numbering Metals and Alloys in the
3.1.12.1 When the purchaser requires thickness tolerances
Unified Numbering System (UNS) 3
for ⁄8 in. [10 mm] minimum edge distance (see Supplementary
Requirement in Specification A568/A568M), this requirement
shall be specified in the purchase order or contract.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
NOTE2—Atypicalorderingdescriptionisasfollows:ASTMA794-XX,
A01.19 on Steel Sheet and Strip.
Cold-Rolled Commercial Steel (CS), Grade 1018, Exposed, Matte Finish,
Current edition approved May 1, 2012. Published May 2012. Originally
Oiled, 0.030 by 36 by 96 in., 100 000 lb., for Part No. 5226 Steel
approved in 1982. Last previous edition approved in 2009 as A794 – 09. DOI:
Shelving, or, ASTM A794M-XX, Cold-Rolled Commercial Steel (CS),
10.1520/A0794_A0794M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A794/A794M−12
Grade 1018, Exposed, Matte Finish, Oiled 0.75 by 915 by 2438 mm, TABLE 2 Limits on
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A794/A794M–09 Designation: A794/A794M – 12
Standard Specification for
Commercial Steel (CS), Sheet, Carbon (0.16 % Maximum to
1
0.25 % Maximum), Cold-Rolled
This standard is issued under the fixed designationA794/A794M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers cold-rolled commercial steel (CS) sheet in coils and cut lengths, in which the maximum of the
specified carbon range is over 0.15 and not over 0.25 %, and the maximum of the specified manganese range is not over 0.90 %.
This material is ordered to chemical composition.
1.2 This specification is not applicable to the steels covered in Specifications A109/A109M and A1008/A1008M.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A109/A109M Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled,
General Requirements for
A749/A749M Specification for Steel, Strip, Carbon and High-Strength, Low-Alloy, Hot-Rolled, General Requirements for
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength
Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable E527
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3
2.2 Society of Automotive Engineers Standard: J1086Numbering Metals and Alloys
J 1086 Numbering Metals and Alloys
3. Ordering Information
3.1 It is the purchaser’s responsibility to specify in the purchase order all ordering information necessary to purchase the needed
material. Examples of such information, include but are not limited to, the following:
3.1.1 ASTM specification number and year of issue,
3.1.2 Name of material (cold-rolled commercial steel (CS) sheet),
3.1.3 Grade designation or chemical composition or both,
3.1.4 Copper-bearing steel (if required),
3.1.5 Finish; indicate unexposed with matte (dull) finish, or exposed with either matte (dull), commercial bright or luster finish,
as required,
3.1.6 Specify oiled or not oiled, as required,
3.1.7 Dimensions (thickness, width, and whether cut lengths or coils),
NOTE 1—Not all producers are capable of meeting all the limitations of the thickness tolerance tables in Specification A568/A568M. The purchaser
should contact the producer regarding possible limitations prior to placing an order.
3.1.8 Coil size (must include inside diameter, outside diameter, and maximum mass),
3.1.9 Quantity,
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.19
on Steel Sheet and Strip.
Current edition approved Nov.May 1, 2009.2012. Published December 2009.May 2012. Originally approved in 1982. Last previous edition approved in 20062009 as
A794 – 069. DOI: 10.1520/A0794_A0794M-0912.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A794/A794M – 12
3.1.10 Application (show part identification and description),
3.1.11 Cast or heat analysis report (request, if required), and
3.1.12 Special requirements (if any).
3
3.1.12.1 When the purchaser requires thickness tolerances for ⁄8 in. [10 mm] minimum edge distance (see Supplementary
Requirement in Specification A568/A568M), this requirement shall be spe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.