ASTM F876-01e1

Standard Specification for Crosslinked Polyethylene (PEX) Tubing

SCOPE
1.1 This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures (see Appendix X1). Included are requirements and test methods for material, workmanship, dimensions, sustained pressure, burst pressure, environmental stress cracking, stabilizer migration resistance, and degree of crosslinking. Methods of marking are also given.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Jan-2001
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.26 - Olefin Based Pipe

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
e1
Designation: F 876 – 01
Standard Specification for
1
Crosslinked Polyethylene (PEX) Tubing
This standard is issued under the fixed designation F 876; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Tables 2 and 3 were editorially updated in February 2002.
1. Scope D 1600 Terminology for Abbreviated Terms Relating to
2
Plastics
1.1 This specification covers crosslinked polyethylene
2
D 1898 Practice for Sampling of Plastics
(PEX) tubing that is outside diameter controlled, made in
D 2122 Test Method for Determining Dimensions of Ther-
standard thermoplastic tubing dimension ratios, and pressure
3
moplastic Pipe and Fittings
rated for water at three temperatures (see Appendix X1).
D 2765 Test Methods for Determination of Gel Content and
Included are requirements and test methods for material,
4
Swell Ratio of Crosslinked Ethylene Plastics
workmanship, dimensions, sustained pressure, burst pressure,
D 2837 Test Method for Obtaining Hydrostatic Design
environmental stress cracking, stabilizer migration resistance,
3
Basis for Thermoplastic Pipe Materials
and degree of crosslinking. Methods of marking are also given.
4
D 3045 Practice for Heat Aging of Plastics Without Load
1.2 The text of this specification references notes, footnotes,
D 3350 Specification for Polyethylene Plastics Pipe and
and appendixes which provide explanatory material. These
4
Fittings Materials
notes and footnotes (excluding those in tables and figures) shall
D 3895 Test Method for Oxidative-Induction Time of Poly-
not be considered as requirements of the specification.
4
olefins by Differential Scanning Calorimetry
1.3 The values stated in inch-pound units are to be regarded
3
F 412 Terminology Relating to Plastic Piping Systems
as the standard. The values given in parentheses are for
2.2 ANSI Standard:
information only.
5
B36.10 Standards Dimensions of Steel Pipe (IPS)
1.4 The following safety hazards caveat pertains only to the
2.3 Federal Standard:
test methods portion, Section 7, of this specification: This
6
FED-STD-123 Marking for Shipment (Civil Agencies)
standard does not purport to address all of the safety concerns,
2.4 Military Standard:
if any, associated with its use. It is the responsibility of the user
6
MIL-STD-129 Marking for Shipment and Storage
of this standard to establish appropriate safety and health
2.5 NSF Standard:
practices and determine the applicability of regulatory limita-
NSF 14 for Plastic Piping Components and Related Mate-
tions prior to use.
7
rials
5
2. Referenced Documents 2.6 ISO Standard:
ISO R 161-1690 Pipes of Plastic Materials for the Transport
2.1 ASTM Standards:
of Fluids (Outside Diameters and Nominal Pressures) Part
D 618 Practice for Conditioning Plastics and Electrical
2
1, Metric Series
Insulating Materials for Testing
D 792 Test Methods for Density and Specific Gravity (Rela-
3. Terminology
2
tive Density) of Plastics by Displacement
3.1 Definitions—Definitions are in accordance with Termi-
D 1505 Test Method for Density of Plastics by the Density-
2
nology F 412, and abbreviations are in accordance with Ter-
Gradient Technique
minology D 1600, unless otherwise specified. The abbreviation
D 1598 Test Method for Time-to-Failure of Plastic Pipe
3
for crosslinked polyethylene is PEX. Plastic tubing denotes a
Under Constant Internal Pressure
particular diameter schedule of plastic pipe in which outside
D 1599 Test Method for Short-Time Hydraulic Failure Pres-
1
3
diameter of the tubing is equal to the nominal size plus ⁄8 in.
sure of Plastic Pipe, Tubing, and Fittings
1 4
This specification is under the jurisdiction of ASTM Committee F-17 on Plastic Annual Book of ASTM Standards, Vol 08.02.
5
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin Available from American National Standards Institute, 11 West 42nd Street,
Based Pipe. 13th Floor, New York, NY 10036.
6
Current edition approved January 10, 2001. Published March 2001. Originally Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
published as F 876 – 84. Last previous edition F 876 – 00. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
2 7
Annual Book of ASTM Standards, Vol 08.01. Available from the National Sanitation Foundation, P.O. Box 1468, Ann Arbor,
3
Annual Book of ASTM Standards, Vol 08.04. MI 48106.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and
...