ASTM D3035-10

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

ABSTRACT
This specification covers polyethylene (PE) pipes made in thermoplastic pipe dimension ratios based on outside diameter, and pressure rated for water. All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, and a system of nomenclature for PE plastic pipe. PE pipes shall be evaluated by the test procedures given herein, and shall conform to specified requirements for workmanship, dimensions, sustained pressure at ambient and elevated temperatures, hydrostatic burst pressure, tensile strength at yield, and environmental stress cracking.
SCOPE
1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter and pressure rated for water (see Appendix X1). Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, a system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, and environmental stress cracking. Methods of marking are also given.  
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Nov-2010
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.26 - Olefin Based Pipe

Relations

• Replaces: ASTM D3035-08 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
• Effective Date: 01-Dec-2010
• Replaced By: ASTM D3035-12 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
• Effective Date: 01-Jul-2012
• Referred By: ASTM F1055-16a(2022) - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
• Effective Date: 01-Dec-2010
• Referred By: ASTM F2880-21 - Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3</num><den>4</den></fraction > in. to 65 in.
• Effective Date: 01-Dec-2010
• Referred By: ASTM F645-18b - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
• Effective Date: 01-Dec-2010
• Referred By: ASTM F3536-22 - Standard Specification for PE and PP Mechanical Fittings for use on NPS 3 or Smaller Cold-water Service Polyethylene (PE) or Crosslinked Polyethylene (PEX) Pipe or Tubing
• Effective Date: 01-Dec-2010
• Referred By: ASTM F2165-19 - Standard Specification for Flexible Pre-Insulated Plastic Piping
• Effective Date: 01-Dec-2010
• Referred By: ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Dec-2010
• Referred By: ASTM F3565-23 - Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service
• Effective Date: 01-Dec-2010
• Referred By: ASTM F3508-21a - Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
• Effective Date: 01-Dec-2010
• Referred By: ASTM D2683-20 - Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
• Effective Date: 01-Dec-2010
• Referred By: ASTM F2620-20ae2 - Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
• Effective Date: 01-Dec-2010
• Referred By: ASTM F2634-15(2021) - Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
• Effective Date: 01-Dec-2010
• Referred By: ASTM F1759-97(2018) - Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
• Effective Date: 01-Dec-2010
• Referred By: ASTM D3350-21 - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
• Effective Date: 01-Dec-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D3035 −10 AnAmerican National Standard
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic
1.1 This specification covers polyethylene (PE) pipe made
Pressure of Plastic Pipe, Tubing, and Fittings
in thermoplastic pipe dimension ratios based on outside diam-
D1600 Terminology forAbbreviatedTerms Relating to Plas-
eter and pressure rated for water (see Appendix X1). Included
tics
are criteria for classifying PE plastic pipe materials and PE
D1603 Test Method for Carbon Black Content in Olefin
plastic pipe, a system of nomenclature for PE plastic pipe, and
Plastics
requirements and test methods for materials, workmanship,
D2122 Test Method for Determining Dimensions of Ther-
dimensions, sustained pressure, burst pressure, and environ-
moplastic Pipe and Fittings
mental stress cracking. Methods of marking are also given.
D2290 Test Method for Apparent Hoop Tensile Strength of
1.2 All pipes produced under this specification may be used
Plastic or Reinforced Plastic Pipe by Split Disk Method
for the transport of water, industrial process liquids, effluents,
D3350 Specification for Polyethylene Plastics Pipe and Fit-
slurries, municipal sewage, etc. The user should consult the
tings Materials
manufacturer to determine whether the material being trans-
D4218 Test Method for Determination of Carbon Black
ported is compatible with polyethylene pipe and will not affect
Content in Polyethylene Compounds By the Muffle-
the service life beyond limits acceptable to the user.
Furnace Technique
1.3 The values stated in inch-pound units are to be regarded F412 Terminology Relating to Plastic Piping Systems
as the standard. The values given in parentheses are for
2.2 NSF International Standards:
information only.
ANSI/NSF Standard No. 14 for Plastic Piping Components
3
1.4 The following safety hazards caveat pertains only to the and Related Materials
test methods portion, Section 7, of this specification: This ANSI/NSF Standard No. 61 for Drinking Water System
3
standard does not purport to address all of the safety concerns, Components—Health Effects
if any, associated with its use. It is the responsibility of the user
2.3 PPI Documents:
of this standard to establish appropriate safety and health
TR-4 Listing of Hydrostatic Design Bases (HDB), Strength
practices and determine the applicability of regulatory limita-
Design Bases (SDB), Pressure Design Bases (PDB) and
tions prior to use.
Minimum Required Strength (MRS) Ratings for Thermo-
4
plastic Piping Materials or Pipe
2. Referenced Documents
TR-9 RecommendedDesignFactorsforThermoplasticPres-
4
2
sure Pipe
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
3. Terminology
D1598 Test Method for Time-to-Failure of Plastic Pipe
3.1 Definitions—Definitions are in accordance with Termi-
nology F412, and abbreviations are in accordance with Termi-
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
nology D1600, unless otherwise specified.
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin
Based Pipe. 3.2 Definitions of Terms Specific to This Standard:
Current edition approved Dec. 1, 2010. Published January 2011. Originally
approved in 1972. Last previous edition approved in 2008 as D3035 – 08. DOI:
10.1520/D3035-10.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from the National Sanitation Foundation, P.O. Box 1468,AnnArbor,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM MI 48106.
4
Standards volume information, refer to the standard’s Document Summary page on Available from the Plastics Pipe Institute, Inc., 1825 Connecticut Ave., NW,
the ASTM website. Suite 680 Washington, DC 20009.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3035−10
TABLE 1 Specification D3350 Cell Classifications for Polyethylene Pipe Materials
PE Material Designation Code PE 1404 PE 2606 PE 2708 PE 3608 PE 3708 PE 3710 PE 4608 PE 4708 PE 4710
Physical Property: Cell Classifications
Density 1 22333444
Melt Index 2 3 or 4 3 or 4
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D3035–08 Designation: D3035 – 10
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 Thisspecificationcoverspolyethylene(PE)pipemadeinthermoplasticpipedimensionratiosbasedonoutsidediameterand
pressure rated for water (see Appendix X1). Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, a
system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained
pressure, burst pressure, and environmental stress cracking. Methods of marking are also given.
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents,
slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is
compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.
1.3 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1603 Test Method for Carbon Black Content in Olefin Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2290 Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218 Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-FurnaceTechnique
F412 Terminology Relating to Plastic Piping Systems
2.2 NSF International Standards:
3
ANSI/NSF Standard No. 14 for Plastic Piping Components and Related Materials
3
ANSI/NSF Standard No. 61 for Drinking Water System Components—Health Effects
2.3 PPI Documents:
TR-4 Listing of Hydrostatic Design Bases (HDB), Strength Design Bases (SDB), Pressure Design Bases (PDB) and Minimum
4
Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe
4
TR-9 Recommended Design Factors for Thermoplastic Pressure Pipe
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin Based
Pipe.
Current edition approved MarchDec. 1, 2008.2010. Published March 2008.January 2011. Originally approved in 1972. Last previous edition approved in 20062008 as
D3035 – 068. DOI: 10.1520/D3035-108.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from the National Sanitation Foundation, P.O. Box 1468, Ann Arbor, MI 48106.
4
Available from the Plastics Pipe Institute, Inc., 1825 Connecticut Ave., NW, Suite 680 Washington, DC 20009.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3035 – 10
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
3.2 Definitions o
...