iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2614-09(2014)

(Specification)

Standard Specification for Condition 3 Bicycle Frames

Standard Specification for Condition 3 Bicycle Frames

ABSTRACT
This specification establishes the testing requirements for the structural performance of Condition 3 bicycle frames. The bicycle frames shall undergo horizontal and vertical loading fatigue tests, and impact strength test in accordance to a referenced ASTM test method. Frames that fail to meet the performance requirements shall be rejected.
SCOPE
1.1 This specification establishes testing requirements for the structural performance properties of Condition 3 bicycle frames.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

General Information

Status
Historical
Publication Date
31-Mar-2014
ICS
43.150 - Cycles
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.10 - Bicycles
Current Stage
Ref Project

Relations

Replaces
ASTM F2614-09 - Standard Specification for Condition 3 Bicycle Frames
Effective Date
01-Apr-2014
Replaced By
ASTM F2614-19 - Standard Specification for Condition 3 Bicycle Frames
Effective Date
15-May-2019

Buy Standard

ASTM F2614-09(2014) - Standard Specification for Condition 3 Bicycle FramesASTM F2614-09(2014) - Standard Specification for Condition 3 Bicycle Frames
PreviousNext
Technical specification
ASTM F2614-09(2014) - Standard Specification for Condition 3 Bicycle Frames
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2614 −09 (Reapproved 2014) An American National Standard
Standard Specification for
Condition 3 Bicycle Frames
This standard is issued under the fixed designation F2614; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This specification defines a set of requirements for Condition 3 bicycle frames. Condition 3 is a
vehicle usage classification defined in Classification F2043 indicating the type of riding and surface
condition intended by design. Included are specifications for establishing loads and other criteria to be
used with the matching test method.
1. Scope 5. Performance Requirements
1.1 This specification establishes testing requirements for
5.1 The bicycle frame shall be tested in accordance with the
the structural performance properties of Condition 3 bicycle
following tests from Test Methods F2711:
frames.
5.1.1 Horizontal Loading Fatigue Test—The frame shall be
1.2 The values stated in SI units are to be regarded as tested and each must complete a minimum 50 000 cycles with
standard. No other units of measurement are included in this a cyclic load of 1200 N tensile and 600 N compressive.
standard.
5.1.2 Vertical Loading Fatigue Test—The frame shall be
tested and each must complete a minimum 50 000 cycles with
2. Referenced Documents
a cyclic load of 1200 N to 120 N load in the compressive
2.1 ASTM Standards:
direction.
F2043 Classification for Bicycle Usage
5.1.3 Impact Strength Test—The frame shall be tested with
F2711 Test Methods for Bicycle Frames
a drop height of 360 mm, and the permanent set of the frame
and fork shall be less than 40 mm.
3. Terminology
3.1 Definitions:
6. Rejection and Rehearing
3.1.1 bicycle frame, n—structural member that supports the
seat with rear connection for the rear wheel, front connection 6.1 Frames that fail to meet the requirements of this
via the head tube for the fork and lower connection for the
standard shall be rejected.
crank/pedal assembly.
7. Certification
4. Classification
7.1 When specified in the purchase order or contract, the
4.1 Condition 3 Bicycle Frame
purchaser shall be furnished certification that specimens have
been either tested or inspected as directed
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2268-03(2023)(Specification)
Standard Specification for Bicycle Serial Numbers

ABSTRACT
The specification establishes the standard format, content, number of characters, and physical requirements for bicycle serial numbers that can help facilitate recall campaigns and identification of the item.
SCOPE
1.1 This standard specifies the format, content, number of characters and physical requirements for serial numbers to facilitate recall campaigns and identification of stolen property.  
1.2 This standard is applicable to all bicycles, refer to Classification F2043 on definition for bicycle.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2918-11(2023)(Test Method)
Standard Test Method for Weighing a Bicycle

SIGNIFICANCE AND USE
5.1 The minimum and as-sold weight of a bicycle are properties used by consumers to evaluate bicycles. The weight may also be used for specifications, manufacturing standards, and quality control.
SCOPE
1.1 This test method covers requirements for weighing and marketing bicycles, including all adult, and childrens bicycles.  
1.2 This standard may contain test methods that do not entirely simulate real life situations. The test methods are designed to give reproducible results in a laboratory and, thereby, a means for product comparison.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1975-15(2023)(Specification)
Standard Specification for Nonpowered Bicycle Trailers Designed for Human Passengers

ABSTRACT
This specification covers nonpowered trailers intended to be pulled behind bicycles to transport one or two children with accessory loads with a prescribed maximum weight. It includes methods for strength, impact drop, structural integrity in rollover, tipover resistance, single-occupant trailer, double-occupant trailer, coupling security, and system fatigue tests. The tests confirm that this specification is satisfied. The specification also prescribes colors, reflectors, and flags for conspicuity.
SCOPE
1.1 This specification covers a nonpowered trailer intended to be pulled behind a bicycle in order to transport one or two children with an accessory load of a maximum weight of 45.4 kg (100 lb). It includes test methods for confirming that this specification is satisfied.  
1.2 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only.  
1.3 The following caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F2793-14(2023)(Specification)
Standard Specification for Bicycle Grips

ABSTRACT
This specification establishes a minimum outer diameter for Bicycle Grips and End Closures applied to tubular handlebars mounted on bicycles designed for cyclists who are 12 years of age or younger. It specifies testing requirements for the durability of the ends of the Bicycle Grips and End Closures for all bicycles where the tubular handlebar end axes are oriented within 60 degrees of parallel to the axle axis of the steering wheel. This specification applies to the "BMX" and "Mountain" style tubular handlebars, but not to the "Drop" (also known as road race) style.
The following characteristics are covered by this specification: Bicycle Grip outer diameter; Bicycle Grip or End Closure diameter or both; and Bicycle Grip or End Closure retention or both. This specification is not intended to dictate the design, materials, or construction of Bicycle Grips and End Closures.
SIGNIFICANCE AND USE
6.1 These tests are intended to address the Bicycle Grip with regard to steering control, durability and potential reduction in injury during an accident.
SCOPE
1.1 This specification establishes a minimum outer diameter for the Bicycle Grip or End Closure, and the method for determining if the grip or End Closure meets the diameter.  
1.2 This specification checks the following characteristics:  
1.2.1 Bicycle Grip outer diameter,  
1.2.2 Bicycle Grip or End Closure diameter or both, and  
1.2.3 Bicycle Grip or End Closure retention or both.  
1.3 This specification establishes testing requirements for the durability of Bicycle Grips and End Closures. It represents a performance standard and is not intended to dictate the design, materials, or construction of those closures.  
1.4 Units—The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2711-19(Test Method)
Standard Test Methods for Bicycle Frames

SIGNIFICANCE AND USE
5.1 These tests are used to verify the durability and strength of a bicycle frame.
SCOPE
1.1 These test methods establish procedures for conducting tests to determine the structural performance properties of bicycle frames.  
1.2 These test methods describe mechanical tests for determining the following performance properties:  
1.2.1 Frame Fatigue – Horizontal Loading  
1.2.2 Frame Fatigue – Vertical Loading  
1.2.3 Falling Mass – Horizontal Loading  
1.2.4 Falling Frame – Vertical Loading  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2802-19(Specification)
Standard Specification for Condition 1 Bicycle Frames

ABSTRACT
This specification establishes the testing requirements for the structural performance of Condition 1 bicycle frames. The bicycle frames shall undergo horizontal and vertical loading fatigue tests, and impact strength test in accordance to a referenced ASTM test method. Frames that fail to meet the performance requirements shall be rejected.
SCOPE
1.1 This specification establishes testing requirements for the structural performance properties of Condition 1 bicycle frames.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2868-19(Specification)
Standard Specification for Condition 2 Bicycle Frames

ABSTRACT
This specification covers general testing requirements for the structural performance properties of Condition bicycle frames. Included are requirements for establishing loads and other criteria to be used with the matching test method. Performance requirements for the bicycle frame shall be in accordance with the methods of Test Methods F2711 which include the Horizontal Loading Fatigue Test, Vertical Loading Fatigue Test, and the Impact Strength Test.
SCOPE
1.1 This standard establishes testing requirements for the structural performance properties of Condition 2 bicycle frames.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard is applicable to adult size suspension and non-suspension bicycle frames.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2843-19(Specification)
Standard Specification for Condition 0 Bicycle Frames

ABSTRACT
This specification establishes testing requirements for the structural performance properties of Condition 0 bicycle frames. Condition 0 is a vehicle usage classification defined in Classification F2043 indicating the type of riding and surface condition intended by design. Included are specifications for establishing loads and other criteria to be used with the matching test method. The bicycle frame shall be tested in accordance with Test Methods F2711, the Horizontal Loading Fatigue test, Vertical Loading Fatigue test, and the Impact Strength test.
SCOPE
1.1 This specification establishes testing requirements for the structural performance properties of Condition 0 bicycle frames.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2614-19(Specification)
Standard Specification for Condition 3 Bicycle Frames

ABSTRACT
This specification establishes the testing requirements for the structural performance of Condition 3 bicycle frames. The bicycle frames shall undergo horizontal and vertical loading fatigue tests, and impact strength test in accordance to a referenced ASTM test method. Frames that fail to meet the performance requirements shall be rejected.
SCOPE
1.1 This specification establishes testing requirements for the structural performance properties of Condition 3 bicycle frames.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2043-13(2018)(Classification)
Standard Classification for Bicycle Usage

SIGNIFICANCE AND USE
4.1 This classification provides a uniform set of usage definitions within the bicycle industry. Included within this classification is a set of graphical indicators to provide retailers and consumers with an indication of the intended use of a particular bicycle or aftermarket components.
SCOPE
1.1 This classification covers bicycle usage conditions and a method of identifying bicycles and components for use within that system.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off