iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2157-09(2018)

(Specification)

Standard Specification for Synthetic Surfaced Running Tracks

Standard Specification for Synthetic Surfaced Running Tracks

ABSTRACT
This specification establishes the minimum performance requirements, classification, and test methods for synthetic surfaced running tracks. Even so, this specification does not imply that an injury cannot be incurred if the surface is found to be in compliance with this specification. The requirements for which newly installed synthetic surfaces shall be tested on and consequently comply to are imperfections, evenness, thickness, drainage, force reduction, modified vertical deformation, texture influence when wet, tensile properties, color in grey scale, weathering, spike resistance, and flammability.
SCOPE
1.1 This specification establishes the minimum performance requirements and classification when tested in accordance with the procedures outlined within this specification. All documents referencing this specification must include classification required.  
1.2 This specification does not imply that an injury cannot be incurred if the surface is found to be in compliance with this specification.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Jun-2018
ICS
97.220.10 - Sports facilities
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.52 - Miscellaneous Playing Surfaces
Current Stage
Ref Project

Relations

Refers
ASTM D2859-15 - Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials
Effective Date
15-Nov-2015
Refers
ASTM D2616-19 - Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale
Effective Date
01-Nov-2019
Refers
ASTM E1131-20 - Standard Test Method for Compositional Analysis by Thermogravimetry
Effective Date
15-Mar-2020
Referred By
ASTM F2772-11(2019) - Standard Specification for Athletic Performance Properties of Indoor Sports Floor Systems
Effective Date
01-Jul-2018

Buy Standard

ASTM F2157-09(2018) - Standard Specification for Synthetic Surfaced Running TracksASTM F2157-09(2018) - Standard Specification for Synthetic Surfaced Running Tracks
PreviousNext
Technical specification
ASTM F2157-09(2018) - Standard Specification for Synthetic Surfaced Running Tracks
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2157 −09 (Reapproved 2018) An American National Standard
Standard Specification for
1
Synthetic Surfaced Running Tracks
This standard is issued under the fixed designation F2157; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
There is a need to provide for the safety of athletes and durability of surfaces used for competition
running. There are a number of sources of injury with regard to the performance of a running track
surface and protection of athletes of all ages.
1. Scope D2950Test Method for Density of Bituminous Concrete in
Place by Nuclear Methods
1.1 Thisspecificationestablishestheminimumperformance
E177Practice for Use of the Terms Precision and Bias in
requirementsandclassificationwhentestedinaccordancewith
ASTM Test Methods
the procedures outlined within this specification. All docu-
E303Test Method for Measuring Surface Frictional Proper-
ments referencing this specification must include classification
ties Using the British Pendulum Tester
required.
E691Practice for Conducting an Interlaboratory Study to
1.2 This specification does not imply that an injury cannot
Determine the Precision of a Test Method
beincurredifthesurfaceisfoundtobeincompliancewiththis
E1131Test Method for CompositionalAnalysis by Thermo-
specification.
gravimetry
1.3 The values stated in SI units are to be regarded as G154Practice for Operating Fluorescent Ultraviolet (UV)
Lamp Apparatus for Exposure of Nonmetallic Materials
standard. No other units of measurement are included in this
standard. 2.2 Other Standards:
DIN 18035 Part 6AStandard for Sports Grounds, Synthetic
1.4 This international standard was developed in accor-
3
Surfacings, Requirements, Test, Maintenance
dance with internationally recognized principles on standard-
IAAFPerformance Specifications for Synthetic Surfaced
ization established in the Decision on Principles for the
4
Athletics Tracks (Outdoors)
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3. Terminology
Barriers to Trade (TBT) Committee.
3.1 Definitions of Terms Specific to This Standard:
3.1.1 compliance, n—a test result that falls within the
2. Referenced Documents
specified range, meets a stated minimum value or achieves a
2
2.1 ASTM Standards:
“pass” rating on a test with a pass/fail result.
D297Test Methods for Rubber Products—ChemicalAnaly-
3.1.2 “D” area, n—an integral part of the synthetic surfac-
sis
ing located within the oval.
D2616Test Method for Evaluation of Visual Color Differ-
ence With a Gray Scale 3.1.3 EPDM components, n—the residual elements of an
D2859Test Method for Ignition Characteristics of Finished EPDM rubber product once the fillers and plasticizers have
Textile Floor Covering Materials been eliminated.
3.1.4 EPDM rubber product, n—a product comprised of
organic and inorganic materials with a minimum of 20% and
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports
a maximum of 26% of ethylene propylene-diene-saturated
Equipment, Playing Surfaces, and Facilitiesand is the direct responsibility of
polymethylene main chain along with other organic and
Subcommittee F08.52 on Miscellaneous Playing Surfaces.
Current edition approved July 1, 2018. Published August 2018. Originally
inorganic components.
approved in 2002. Last previous edition approved in 2009 as F2157–09. DOI:
10.1520/F2157-09R18.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from Beuth Verlag GmbH (DIN-- DIN Deutsches Institut fur
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Normung e.V.), Burggrafenstrasse 6, 10787, Berlin, Germany.
4
Standards volume information, refer to the standard’s Document Summary page on Available from IAAF Headquarters, 17 rue Princesse Florestine—BP 359,
the ASTM website. MC-98007, Monaco Cedex. http://www.iaaf.org
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2157 − 09 (2018)
3.1.5 flat, n—an area that by design is to have a finished 5. Test Methods and Requirements for Asphalt Base
slope of 0.5% or less.
5.1 Type and Compaction:
3.1.6 recycled black EPDM rubber product, n—crumbs or
5.1.1 Description and Required Performance—The asphalt
granules manufactured through ambient or cryogenic grinding
base and asphalt we
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1777-19(2023)(Practice)
Standard Practice for Paintball Game Site Operation

ABSTRACT
This practice sets forth procedures for operating a paintball playing field. The goal is to assist paintball field operators in running a safe business. Like any other physical activity, paintball presents a potential for injury. No procedural practice can prevent all injuries, especially when paintball players do not follow safety instructions. The ultimate responsibility for preventing injury lies with the paintball player. This practice, however, intends to promote safe paintball field operation through standardization of operating practice.
SCOPE
1.1 This practice establishes minimum safety requirements for the operation of paintball playing game sites, and provides for certain materials and procedures required.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1015-21(Test Method)
Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces

SIGNIFICANCE AND USE
5.1 Data obtained from the procedure of this test method are indicative of the relative abrasiveness of fabric or carpet type synthetic playing surfaces.
SCOPE
1.1 This test method is applicable to both laboratory and field measurement of synthetic turf surfaces used for sports.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3188-16(2021)(Specification)
Standard Specification for Extractable Hazardous Metals in Synthetic Turf Infill Materials

ABSTRACT
This specification covers all extractable hazardous metals (man-made or natural) that are intended for use as infill materials for synthetic turf sports surfaces. It specifies the amount of certain metals that have the potential to be extracted from synthetic turf infill materials if ingested. The time, temperature, and pH of the extraction fluid approximate the conditions the infill material would experience in the stomach during the digestive process. The levels of extractable metals are compared to maximum levels allowed in children's toys.
This specification includes requirements with respect to performance (hazardous metal content), test methods, sampling, apparatus, reagents, and procedure.
SIGNIFICANCE AND USE
7.1 This test method is based on subsection 8.3 of Consumer Safety Specification F963, which specifies a test procedure to determine the amount of hazardous metals that have the potential to be present in toys and handled or ingested by children. Since it is possible for users of synthetic turf playing surfaces to handle or ingest particles of synthetic turf infill materials, it is necessary to determine the level of hazardous metals in the synthetic turf infill materials. The limits of hazardous metals used in this specification are based on those specified in Consumer Safety Specification F963, adjusted for statistical error correction factor as described in Consumer Safety Specification F963.
SCOPE
1.1 This specification relates to the amount of certain metals that have the potential to be extracted from synthetic turf infill materials if ingested. The time, temperature, and pH of the extraction fluid approximate the conditions the infill material would experience in the stomach during the digestive process. The levels of extractable metals are compared to maximum levels allowed in children’s toys.  
1.2 This specification applies to all materials (man-made or natural) that are intended for use as infill materials for synthetic turf sports surfaces.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2940-21(Practice)
Standard Practice for Air Soft Field Operation

ABSTRACT
This practice sets forth procedures for the operation of air soft playing fields, intended to assist air soft field operators in running a safe business. It covers eye protection devices suitable for use in air soft games, including goggles, and recommends the minimum engagement distance between the shooter and the target at which a shot may be fired. It also requires the conspicuous posting of player safety rules, printed in 24-point type or larger, at the registration area.
SCOPE
1.1 This practice establishes minimum safety requirements for the operation of air soft playing fields, and provides for certain materials and procedures required.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2765-14(2021)(Specification)
Standard Specification for Total Lead Content in Synthetic Turf Fibers

ABSTRACT
This specification details the test methods for sample preparation and analyzing, as well as guidelines for reporting the total lead content in fibers used in synthetic turf. Synthetic turf fibers shall be tested at such quantity intervals as to ensure continuing compliance with test requirements. The measured total lead content shall be within the limit specified herein.
SCOPE
1.1 This specification applies to the maximum content of lead in fibers used in synthetic turf.  
1.1.1 This specification outlines a test method for sample preparation and a test method for analyzing the total lead content in synthetic turf fibers.  
1.1.2 This specification outlines guidelines for reporting total lead content in synthetic turf fibers.  
1.2 This specification applies only to synthetic turf fibers manufactured after Sept. 1, 2009.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3496-20(Specification)
Standard Specification for Polyaromatic Hydrocarbon (PAH) Content in Synthetic Turf Infill

SCOPE
1.1 This specification applies to the maximum content of eight PAHs (PAH8) in materials used as synthetic turf infill.  
1.2 This specification outlines a test method for sample preparation and the method for analyzing the content of the eight PAHs in synthetic turf infill.  
1.3 This specification provides guidelines for reporting the content of the eight PAHs in the synthetic turf infill.  
1.4 This specification is applicable to any infill material used in synthetic turf.  
1.5 The values stated in SI units are to be regarded as standard. No other units are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3189-20(Test Method)
Standard Test Method for Measuring Force Reduction, Vertical Deformation, and Energy Restitution of Synthetic Turf Systems Using the Advanced Artificial Athlete

SIGNIFICANCE AND USE
5.1 The dynamic interaction between the athlete and the synthetic turf surface affects the comfort and the performance of the athlete. Interaction with a surface that has low amounts of deformation and shock absorption allows the player to run fast and turn quickly, but has the potential to cause discomfort and damage to the lower extremity joints. Synthetic turf surfaces having high deformation have lower energy restitution. Less of the energy exerted by the athlete returns from the surface, possibly increasing the fatigue for the performing athlete.
SCOPE
1.1 This test method specifies a method for measuring force reduction, vertical deformation, and energy restitution of synthetic turf surfaces.  
1.2 This method is used to characterize properties of synthetic turf systems including the turf fabric, infill material, and shock pad (if applicable).  
1.3 It can be used for characterizing synthetic turf systems in laboratory environment or in the field.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2107-08(2020)(Guide)
Standard Guide for Construction and Maintenance of Skinned Areas on Baseball and Softball Fields

SIGNIFICANCE AND USE
4.1 The skinned areas of baseball and softball fields should provide a uniform playing surface of high quality. Ball bounce should be true and predictable. Footing and sliding properties should favor optimum performance of players. Undulations, rough surface, hard or soft surfaces, weeds, stones, and wet spots detract from good play. Playing surface quality is largely affected by construction and maintenance procedures, and this standard guide addresses those procedures. While warning tracks are a type of skinned area found on baseball and softball fields, this standard does not apply to warning tracks. A separate standard, Guide F2270, presents information pertaining to warning tracks.  
4.1.1 During construction, consideration should be given to factors such as the physical and chemical properties of materials used in the area, freedom from stones and other debris, and surface and internal drainage.  
4.1.2 Maintenance practices that influence the playability of the surface include edging, dragging, rolling, watering, vegetation control, brushing or hosing to prevent buildup of a lip of mineral matter in turfgrass at the skinned/turfed edges, and removal of stones and debris that may adversely affect play and safety.  
4.2 Those responsible for the design, construction, or maintenance, or a combination thereof, of skinned areas on baseball and softball fields will benefit from this guide.  
4.3 This guide provides flexibility in choices of procedures and can be used to cover a variety of use and budget levels.
SCOPE
1.1 This guide covers techniques that are appropriate for the construction and maintenance of skinned areas on baseball and softball fields. This guide provides guidance for the selection of materials, such as soil, sand, gravel, crushed stone, crushed brick, calcined clay, calcined diatomaceous earth, vitrified clay, etc., for use in constructing or reconditioning skinned areas and for the selection of management practices that will maintain a safe and playable skinned surface. Although this guide is specific to baseball/softball, it has application to other sports where ball bounce, ball roll, or player footing, or a combination thereof, are of importance.  
1.2 Decisions in selecting construction and maintenance techniques are influenced by existing soil types, climatic factors, level of play, intensity of use, equipment available, budget, and training and ability of management personnel.  
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. The ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Tra...

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3339-20(Guide)
Standard Guide for Construction or Renovation of Native-soil Athletic Fields

SIGNIFICANCE AND USE
4.1 A dense, uniform, smooth and vigorously growing natural turfgrass sports field provides the ideal and preferred playing surface for most outdoor field sports. Such a surface is pleasing to the spectators and athletes. A thick, consistent and smooth grass cover also increases playing quality and safety by providing stable footing for the athletes, cushioning their impact from falls, slides or tackles and cools the playing surface during hot weather.  
4.2 Sand is commonly used to construct high performance athletic field rootzone systems. Sand is chosen as the primary construction material for two basic properties; compaction resistance and improved drainage/aeration state. Although sand-based fields generally provide for a higher level of performance, the costs associated with constructing/developing a proper, high-performance sand-based field often precludes its use for many athletic field construction projects. In these instances soil-based fields constructed with either native or imported soils; either topsoil or subsoil material modified to mimic the properties of a natural topsoil (a manufactured topsoil). These soils are sometimes modified with amendments to improve their performance properties either at the time of original construction or during a subsequent renovation. Although not approaching the same performance properties of a proper sand-based field construction; the implementation of proper design, construction, and athletic field maintenance can produce soil-based athletic field rootzones with acceptable performance characteristics.  
4.3 Properties of both the soil and grass plants must be considered in planning, constructing, and maintaining a high quality athletic field installation. Turfgrass utilized must be adapted to the local growing conditions and be capable of forming a thick, dense, turf cover at the desired mowing height. Soil-based fields provide varying levels of soil stability but such conditions often deteriorate rapidly under hi...
SCOPE
1.1 This guide covers techniques that are appropriate for the construction of athletic field rootzones using native-soil. This guide is also applicable to soils which are not native to the site but are natural (non-sand) imported soils. This guide provides guidance for the selection of soil materials, amendments, and methods for use in constructing these types of athletic field rootzones. Soils having a texture of Sandy Loam or coarser should be utilized for soil-based rootzone construction. Soils which are finer textured than listed above may be employed for rootzone construction but should be sand-modified to meet the performance criteria of this standard. If fields are constructed with soils which are finer textured, they will not be capable of meeting the performance criteria in this standard. Despite performance limitations, fields which are constructed with finer textured soils (due to logistics or budget constraints) may still be able to conform to the slope/grade criteria (see 5.1, 5.4, and Table 1). Sand modified rootzone constructions are not addressed by this standard.  
1.2 Decisions in selecting construction and maintenance techniques are influenced by existing soil types, climatic factors, level of play, intensity and frequency of use, equipment available, budget and training, and the ability of management personnel.  
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, ...

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM F3415-20(Test Method)
Standard Test Method for Triaxial Shear Strength and Cohesion of Equine Sports Surfaces

SIGNIFICANCE AND USE
5.1 To test the shear strength of a materials describing how the material resists sliding of surface layers. Data from these tests are used to calculate the friction angle and cohesion of a surface sample. This test can be used to help determine if a material falls within a suitable for equine sports surfaces.
SCOPE
1.1 This adapted test method covers the determination of strength and stress-strain relationships of a cylindrical specimen of a compacted, drained cohesive natural or synthetic soil surface used in equine sports surfaces. Specimens are isotropically consolidated and sheared in compression at a constant rate of axial deformation (strain controlled).  
1.2 The shear strength of an equine sports surface material describes the resistance of the material to sliding of the surface layers. Shear strength influences both slide and penetration of the hoof in the track surface. It is generally accepted that a small amount of slide on impact is desirable (1-3).2 However, the surface must have sufficient shear strength to support the horse during propulsion (1-5). Thus, an optimal shear strength would be expected for an equestrian surface.  
1.3 To determine the shear strength of an equine sports surface, a representative dirt or synthetic sample is placed into a cylindrical cell and a vertical load is applied. Shear strength is measured as per the procedures outlined in Test Method D4767 for lab-consolidated samples. This ASTM standard was adapted by Racing Surfaces Testing Laboratory for the drained condition to more accurately model the conditions of an equestrian surface.  
1.4 Dirt samples are tested over a range of forming moisture contents to determine the maximum bulk density and optimal forming moisture content for a given energy input. The dirt samples are then compacted at this optimal moisture content. The maximum stress failure criteria is assumed and results are presented as the failure stress at 15 psi confining pressure versus sample forming moisture content, along with friction angle and cohesion.  
1.5 Synthetic samples with good drainage are tested at a 4% forming moisture content, and over a specified range of temperatures. The temperature is controlled using a heated/refrigerated water bath with a triaxial cell cap fitted with a copper coil. Failure criteria is assumed under similar conditions for the dirt surfaces, and results are presented as the failure stress at 15 psi confining pressure versus sample temperature, along with friction angle and cohesion.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off