ASTM F1015-21
(Test Method)Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces
Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces
SIGNIFICANCE AND USE
5.1 Data obtained from the procedure of this test method are indicative of the relative abrasiveness of fabric or carpet type synthetic playing surfaces.
SCOPE
1.1 This test method is applicable to both laboratory and field measurement of synthetic turf surfaces used for sports.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1015 − 21 An American National Standard
Standard Test Method for
1
Relative Abrasiveness of Synthetic Turf Playing Surfaces
This standard is issued under the fixed designation F1015; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 synthetic turf playing surface—a man-made playing
surface incorporating artificial grass-like fibers.
1.1 This test method is applicable to both laboratory and
3.1.2 abrasiveness—that property of a synthetic turf which
field measurement of synthetic turf surfaces used for sports.
causes material in moving contact with the turf surface to wear
1.2 The values stated in SI units are to be regarded as the
away.
standard. The values given in parentheses are for information
3.1.3 abrasiveness index—a number equal to the weight lost
only.
in grams per foot of travel of a standard weighted friable foam
1.3 This standard does not purport to address all of the
set multiplied by 100, when the foam is pulled through a
safety concerns, if any, associated with its use. It is the
complete 1.8-m (6-ft) test cycle.
responsibility of the user of this standard to establish appro-
3.1.4 foam friability index—a number equal to the percent
priate safety, health, and environmental practices and deter-
mass loss of foam when tested in accordance with the
mine the applicability of regulatory limitations prior to use.
Procedure section of Test Method C421.
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
4. Summary of Test Method
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4.1 Friable foam blocks are attached to a weighted platform
mendations issued by the World Trade Organization Technical
which is pulled over the playing surface in a prescribed
Barriers to Trade (TBT) Committee.
manner. The weight of foam abraded away determines the
relative abrasiveness of the surface.
2. Referenced Documents
2
5. Significance and Use
2.1 ASTM Standards:
C421 Test Method for Tumbling Friability of Preformed
5.1 Data obtained from the procedure of this test method are
Block-Type and Preformed Pipe-Covering-Type Thermal
indicative of the relative abrasiveness of fabric or carpet type
Insulation
synthetic playing surfaces.
E105 Guide for Probability Sampling of Materials
E122 Practice for Calculating Sample Size to Estimate,With
6. Apparatus
Specified Precision, the Average for a Characteristic of a
6.1 Abrasiveness Test Platform—A test platform is used to
Lot or Process
support the load on the friable foam material. The platform
F355 TestMethodforImpactAttenuationofPlayingSurface
shall consist of a 20.3 by 20.3 cm (8.00 by 8.00 in.) square of
Systems, Other Protective Sport Systems, and Materials
0.635-cm thick (0.25 in.) aluminum. Holes 0.635 cm in
Used for Athletics, Recreation and Play
diameter shall be centered 0.635 cm from the midpoint of each
edge to permit attachment of a suitable hook for pulling. Foam
3. Terminology
1 1
retaining strips, ⁄4 in. high by ⁄2 in. wide, defining 2 by 2-in.
3.1 Definitions of Terms Specific to This Standard:
squares, are attached at each corner (Fig. 1). The completed
platform should weigh 931 6 28 g.
6.2 Test Weight—A flat-head (9.072-kg (20.00-lb)) missile
1
This test method is under the jurisdiction of ASTM Committee F08 on Sports
asusedinTestMethodF355,ProcedureA,canbeusedasatest
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.65 on Artificial Turf Surfaces and Systems.
weight. A suitable alternative weight is a steel cylinder about
Current edition approved Dec. 1, 2021. Published January 2022. Originally
15.2 cm (6.00 in.) in diameter and about 6.35 cm (2.50 in.) in
approved in 1986. Last previous edition approved in 2017 as F1015 – 03 (2017).
height. The test weight is to be within 56 g (2 oz) of its
DOI: 10.1520/F1015-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or specified weight.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.3 Pull Cable and Direction Changing Pulley—Adirection
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. changing pulley attached to an operator foot restraint may be
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1015 − 03 (Reapproved 2017) F1015 − 21 An American National Standard
Standard Test Method for
1
Relative Abrasiveness of Synthetic Turf Playing Surfaces
This standard is issued under the fixed designation F1015; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method is applicable to both laboratory and field measurement of synthetic turf surfaces used for sports.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C421 Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation
E105 Guide for Probability Sampling of Materials
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or
Process
F355 Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for
Athletics, Recreation and Play
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 synthetic turf playing surface—a man-made playing surface incorporating artificial grass-like fibers.
3.1.2 abrasiveness—that property of a synthetic turf which causes material in moving contact with the turf surface to wear away.
3.1.3 abrasiveness index—a number equal to the weight lost in grams per foot of travel of a standard weighted friable foam set
multiplied by 100, when the foam is pulled through a complete 1.8-m (6-ft) test cycle.
1
This test method is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of Subcommittee
F08.65 on Artificial Turf Surfaces and Systems.
Current edition approved Dec. 1, 2017Dec. 1, 2021. Published December 2017January 2022. Originally approved in 1986. Last previous edition approved in 20092017
as F1015 – 03 (2009).(2017). DOI: 10.1520/F1015-03R17.10.1520/F1015-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1015 − 21
3.1.4 foam friability index—a number equal to the percent mass loss of foam when tested in accordance with the Procedure section
of Test Method C421.
4. Summary of Test Method
4.1 Friable foam blocks are attached to a weighted platform which is pulled over the playing surface in a prescribed manner. The
weight of foam abraded away determines the relative abrasiveness of the surface.
5. Significance and Use
5.1 Data obtained from the procedure of this test method are indicative of the relative abrasiveness of fabric or carpet type
synthetic playing surfaces.
6. Apparatus
6.1 Abrasiveness Test Platform—A test platform is used to support the load on the friable foam material. The platform shall consist
of a 20.3 by 20.3 cm (8.00 by 8.00 in.) square of 0.635-cm thick (0.25 in.) aluminum. Holes 0.635 cm in diameter shall be centered
1
0.635 cm from the midpoint of each edge to permit attachment of a suitable hook for pulling. Foam retaining strips, ⁄4 in. high
1
by ⁄2 in. wide, defining 2 by 2-in. squares, are attached at each corner (Fig. 1). The completed platform should weigh 931 6 28
g.
6.2 Test Weight—A flat-head (9.072-kg (20.00-lb)) missile as used in Test Method F355, Procedure A, can be used as a test weight.
A suitable alternative w
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.