Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled

ABSTRACT
This specification covers hot-rolled carbon steel sheet and strip, in coils and cut lengths. The cast or heat analysis of the steel shall conform to the chemical composition for copper, nickel, chromium, molybdenum, vanadium, and columbium. The bending properties are measured.
SCOPE
1.1 This specification covers hot-rolled carbon steel (CS) sheet and strip, in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and not over 0.25 % and the maximum of the specified manganese range is not over 0.90 %. This material is ordered to chemical composition.  
1.2 This specification is not applicable to the steels covered by Specification A635/A635M.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

General Information

Status
Historical
Publication Date
30-Apr-2012
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A659/A659M-12 - Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM A659/A659M-12 - Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A659/A659M −12
Standard Specification for
Commercial Steel (CS), Sheet and Strip, Carbon (0.16
1
Maximum to 0.25 Maximum Percent), Hot-Rolled
This standard is issued under the fixed designationA659/A659M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
3
1. Scope* 2.2 Society of Automotive Engineers Standard:
J 1086 Numbering Metals and Alloys
1.1 This specification covers hot-rolled carbon steel (CS)
sheet and strip, in coils and cut lengths, in which the maximum
3. Ordering Information
of the specified carbon range is over 0.15 and not over 0.25 %
and the maximum of the specified manganese range is not over 3.1 It is the purchaser’s responsibility to specify in the
0.90 %. This material is ordered to chemical composition.
purchase order all ordering information necessary to purchase
the needed material. Examples of such information include but
1.2 This specification is not applicable to the steels covered
are not limited to the following:
by Specification A635/A635M.
3.1.1 ASTM specification number and year of issue,
1.3 The values stated in either SI units or inch-pound units
3.1.2 Name of material (hot-rolled commercial steel (CS)
are to be regarded separately as standard. The values stated in
sheet, or hot-rolled commercial steel (CS) strip),
each system may not be exact equivalents; therefore, each
3.1.3 Grade designation or chemical composition, or both,
system shall be used independently of the other. Combining
3.1.4 Copper-bearing steel (if required),
values from the two systems may result in non-conformance
3.1.5 Condition (as-rolled, pickled, or blast cleaned) (see
with the standard.
4.1),
3.1.5.1 Material to this specification is furnished in the
2. Referenced Documents
hot-rolled condition. Pickled (or blast cleaned) must be speci-
2
2.1 ASTM Standards: fied if required,
A568/A568M Specification for Steel, Sheet, Carbon, 3.1.6 Oiling (see 7.2),
Structural,andHigh-Strength,Low-Alloy,Hot-Rolledand 3.1.7 Edges (see 7.1),
Cold-Rolled, General Requirements for 3.1.8 Dimensions(thickness,width,andwhethercutlengths
A635/A635M Specification for Steel, Sheet and Strip, or coils),
Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon,
NOTE 1—Not all producers are capable of meeting all of the limitations
Structural, High-Strength Low-Alloy, and High-Strength
of the thickness tolerance tables in Specification A568/A568M. The
Low-Alloy with Improved Formability, General Require-
purchaser should contact the producer regarding possible limitations prior
to placing an order.
ments for
A749/A749M Specification for Steel, Strip, Carbon and
3.1.9 Coil size (must include inside diameter, outside
High-Strength, Low-Alloy, Hot-Rolled, General Require-
diameter, and maximum mass),
ments for
3.1.10 Quantity,
E527 Practice for Numbering Metals and Alloys in the
3.1.11 Application (show part identification and
Unified Numbering System (UNS)
description),
3.1.12 Cast or heat analysis report (request, if required),
3.1.13 Special requirements (if required).
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, 3.1.13.1 When the purchaser requires thickness tolerances
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
for 3/8 in. [10 mm] minimum edge distance (see Supplemen-
A01.19 on Steel Sheet and Strip.
tary Requirement in Specification A568/A568M), this require-
Current edition approved May 1, 2012. Published May 2012. Originally
ment shall be specified in the purchase order or contract.
approved in 1972. Last previous edition approved in 2010 as A659/A659M – 10.
DOI: 10.1520/A0659_A0659M-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A659/A659M−12
NOTE 2—A typical ordering description is as follows: TABLE 2 Limits on Unspecified Elements (see 5.1.1)
“ASTM A659-XX [or A659M-XX], Hot-Rolled Commercial Steel (CS) A
Copper, max % Heat analysis 0.20
Sheet, Grade 1017, Pickled and Oiled, Cut Edge, 0.075 by 36 in. [or 1.85
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A659/A659M–10 Designation: A659/A659M – 12
Standard Specification for
Commercial Steel (CS), Sheet and Strip, Carbon (0.16
1
Maximum to 0.25 Maximum Percent), Hot-Rolled
This standard is issued under the fixed designationA659/A659M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers hot-rolled carbon steel (CS) sheet and strip, in coils and cut lengths, in which the maximum of the
specified carbon range is over 0.15 and not over 0.25 % and the maximum of the specified manganese range is not over 0.90 %.
This material is ordered to chemical composition.
1.2 This specification is not applicable to the steels covered by Specification A635/A635M.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled,
General Requirements for
A635/A635M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural,
High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
A749/A749M Specification for Steel, Strip, Carbon and High-Strength, Low-Alloy, Hot-Rolled, General Requirements for
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3
2.2 Society of Automotive Engineers Standard:
J 1086 Numbering Metals and Alloys
3. Ordering Information
3.1 Itisthepurchaser’sresponsibilitytospecifyinthepurchaseorderallorderinginformationnecessarytopurchasetheneeded
material. Examples of such information include but are not limited to the following:
3.1.1 ASTM specification number and year of issue,
3.1.2 Name of material (hot-rolled commercial steel (CS) sheet, or hot-rolled commercial steel (CS) strip),
3.1.3 Grade designation or chemical composition, or both,
3.1.4 Copper-bearing steel (if required),
3.1.5 Condition (as-rolled, pickled, or blast cleaned) (see 4.1),
3.1.5.1 Material to this specification is furnished in the hot-rolled condition. Pickled (or blast cleaned) must be specified if
required,
3.1.6 Oiling (see 7.2),
3.1.7 Edges (see 7.1),
3.1.8 Dimensions (thickness, width, and whether cut lengths or coils),
NOTE 1—Not all producers are capable of meeting all of the limitations of the thickness tolerance tables in SpecificationA568/A568M. The purchaser
should contact the producer regarding possible limitations prior to placing an order.
3.1.9 Coil size (must include inside diameter, outside diameter, and maximum mass),
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.19
on Steel Sheet and Strip.
Current edition approved AprilMay 1, 2010.2012. Published April 2010.May 2012. Originally approved in 1972. Last previous edition approved in 20082010 as
A659/A659M – 108. DOI: 10.1520/A0659_A0659M-102.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A659/A659M – 12
3.1.10 Quantity,
3.1.11 Application (show part identification and description),
3.1.12 Cast or heat analysis report (request, if required),
3.1.13 Special requirements (if required).
3.1.13.1 When the purchaser requires thickness tolerances for 3/8 in. [10 mm] minimum edge distance (see Supplementary
Requirement in Specification A568/A568M), this requirement shall be specified in th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.