ASTM F1898-08(2015)
(Specification)Standard Specification for Helmets for Non-Motorized Wheeled Vehicle Used by Infants and Toddlers
Standard Specification for Helmets for Non-Motorized Wheeled Vehicle Used by Infants and Toddlers
ABSTRACT
This specification covers the performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of non-motorized wheeled vehicles. The performance requirements to which the helmets shall conform include those for headforms, peripheral vision, retention system testing, anvils and impact velocities, impact sites, impacting schedule, and peak acceleration.
SCOPE
1.1 This specification covers performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of nonmotorized vehicles intended for their use. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict design.
1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except as noted.
1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in their entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard.
1.4 Headgear that complies with this and other standards may proclaim uses as described in those standards as certified by the manufacturer.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1898 −08(Reapproved 2015) An American National Standard
Standard Specification for
Helmets for Non-Motorized Wheeled Vehicle Used by Infants
and Toddlers
This standard is issued under the fixed designation F1898; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Evaluating the Performance Characteristics of Protective
Headgear
1.1 This specification covers performance requirements for
helmets manufactured for use by infants and toddlers as
3. Labels and Warnings
passengers or operators of nonmotorized vehicles intended for
3.1 In addition to the labeling requirements outlined in Test
their use. This specification recognizes the desirability of
Methods F1446, the helmet shall have the words “For use by
lightweight construction and ventilation; however, it is a
infants and toddlers when riding non-motorized wheeled ve-
performance standard and is not intended to restrict design.
hicles intended for their use” inscribed on one of the interior
1.2 All testing and requirements of this specification shall
permanent labels.
be in accordance with Test Methods F1446 except as noted.
4. Marking the Test Line
1.3 Partial utilization of this standard is prohibited. Any
4.1 The test line is shown in Fig. 1 and shall be marked in
statement of compliance with this specification must be a
accordance with Test Methods F1446.
certification that the product meets all of the requirements of
this specification in their entirety. A product that fails to meet
5. Conditioning and Number of Samples
any one of the requirements of this specification is considered
5.1 Four helmets of each model and size are required for
to have failed this standard, and should not be sold with any
testing.
indication that it meets parts of this standard.
5.2 Conditioning of test samples is described in Test Meth-
1.4 Headgear that complies with this and other standards
ods F1446.
may proclaim uses as described in those standards as certified
6. Headforms
by the manufacturer.
1.5 The values stated in SI units are to be regarded as 6.1 Headforms to be used in this specification are sizes A
standard. No other units of measurement are included in this and E according to Test Methods F1446. The appropriate size
headform shall be selected in accordance with Test Methods
standard.
F1446 for the helmet to be tested.
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 6.2 The weight of the drop assembly as specified in Test
responsibility of the user of this standard to establish appro-
MethodsF1446shallbe3.20 60.15kgfortheAheadformand
priate safety and health practices and determine the applica- 4.00 6 0.20 kg for the E headform.
bility of regulatory limitations prior to use.
6.3 The headform center of gravity specified in Appendix
X1 of Test Methods F1446 will be allowed an additional
2. Referenced Documents
tolerance in the X-axis.The tolerance allows the location of the
2.1 ASTM Standards:
center of gravity to lie between -6.5 mm and 40 mm of the
F1446 Test Methods for Equipment and Procedures Used in
center of the ball socket (positive X is toward the monorail
where applicable).
7. Peripheral Vision Requirement
This specification is under the jurisdiction ofASTM Committee F08 on Sports
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
7.1 The peripheral vision requirements shall be as specified
Subcommittee F08.53 on Headgear and Helmets.
in Test Methods F1446.
Current edition approved Jan. 1, 2015. Published February 2015. Originally
approved in 1998. Last previous edition approved in 2008 as F1898 – 08. DOI:
8. Retention System Testing
10.1520/F1898-08R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
8.1 Retention system tests will be performed before impact
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
testing.The retention system shall be tested in accor
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1898 − 08 F1898 − 08 (Reapproved 2015) An American National Standard
Standard Specification for
Helmets for Non-Motorized Wheeled Vehicle Used by Infants
and Toddlers
This standard is issued under the fixed designation F1898; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers performance requirements for helmets manufactured for use by infants and toddlers as passengers
or operators of nonmotorized vehicles intended for their use. This specification recognizes the desirability of lightweight
construction and ventilation; however, it is a performance standard and is not intended to restrict design.
1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except as noted.
1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification
that the product meets all of the requirements of this specification in their entirety. A product that fails to meet any one of the
requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets
parts of this standard.
1.4 Headgear that complies with this and other standards may proclaim uses as described in those standards as certified by the
manufacturer.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
F1446 Test Methods for Equipment and Procedures Used in Evaluating the Performance Characteristics of Protective Headgear
3. Labels and Warnings
3.1 In addition to the labeling requirements outlined in Test Methods F1446, the helmet shall have the words “For use by infants
and toddlers when riding non-motorized wheeled vehicles intended for their use” inscribed on one of the interior permanent labels.
4. Marking the Test Line
4.1 The test line is shown in Fig. 1 and shall be marked in accordance with Test Methods F1446.
5. Conditioning and Number of Samples
5.1 Four helmets of each model and size are required for testing.
5.2 Conditioning of test samples is described in Test Methods F1446.
6. Headforms
6.1 Headforms to be used in this specification are sizes A and E according to Test Methods F1446. The appropriate size
headform shall be selected in accordance with Test Methods F1446 for the helmet to be tested.
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.53 on Headgear and Helmets.
Current edition approved May 15, 2008Jan. 1, 2015. Published June 2008February 2015. Originally approved in 1998. Last previous edition approved in 20012008 as
F1898 – 01.F1898 – 08. DOI: 10.1520/F1898-08.10.1520/F1898-08R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1898 − 08 (2015)
Dimension
Headform X L/2 Y R S T U
Size
A 24.0 88.0 89.7 30.0 15.0 118.0 63.0
E 26.0 94.5 96.0 32.0 16.0 126.5 67.5
NOTE 1—This test line drawing shows test lines on helmet rather than on headform and uses dimensional nomenclature R, S, T, U as in other drawings
(forme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.