ASTM D7169-20
(Test Method)Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
SIGNIFICANCE AND USE
5.1 The determination of the boiling point distribution of crude oils and vacuum residues, as well as other petroleum fractions, yields important information for refinery operation. These boiling point distributions provide information as to the potential mass percent yield of products. This test method may provide useful information that can aid in establishing operational conditions in the refinery. Knowledge of the amount of residue produced is important in determining the economics of the refining process.
SCOPE
1.1 This test method covers the determination of the boiling point distribution and cut point intervals of crude oils and residues by using high temperature gas chromatography. The amount of residue (or sample recovery) is determined using an external standard.
1.2 This test method extends the applicability of simulated distillation to samples that do not elute completely from the chromatographic system. This test method is used to determine the boiling point distribution through a temperature of 720 °C. This temperature corresponds to the elution of n-C100.
1.3 This test method is used for the determination of boiling point distribution of crude oils. This test method uses capillary columns with thin films, which results in the incomplete separation of C4-C8 in the presence of large amounts of carbon disulfide, and thus yields an unreliable boiling point distribution corresponding to this elution interval. In addition, quenching of the response of the detector employed to hydrocarbons eluting during carbon disulfide elution, results in unreliable quantitative analysis of the boiling distribution in the C4-C8 region. Since the detector does not quantitatively measure the carbon disulfide, its subtraction from the sample using a solvent-only injection and corrections to this region via quenching factors, results in an approximate determination of the net chromatographic area. A separate, higher resolution gas chromatograph (GC) analysis of the light end portion of the sample may be necessary in order to obtain a more accurate description of the boiling point curve in the interval in question as described in Test Method D7900 (see Appendix X1).
1.4 This test method is also designed to obtain the boiling point distribution of other incompletely eluting samples such as atmospheric residues, vacuum residues, etc., that are characterized by the fact that the sample components are resolved from the solvent.
1.5 This test method is not applicable for the analysis of materials containing a heterogeneous component such as polyesters and polyolefins.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 8.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7169 − 20
Standard Test Method for
Boiling Point Distribution of Samples with Residues Such
as Crude Oils and Atmospheric and Vacuum Residues by
1
High Temperature Gas Chromatography
This standard is issued under the fixed designation D7169; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.5 This test method is not applicable for the analysis of
materials containing a heterogeneous component such as
1.1 Thistestmethodcoversthedeterminationoftheboiling
polyesters and polyolefins.
point distribution and cut point intervals of crude oils and
residues by using high temperature gas chromatography. The 1.6 Thevaluesstatedininch-poundunitsaretoberegarded
amount of residue (or sample recovery) is determined using an as standard. The values given in parentheses are mathematical
external standard. conversions to SI units that are provided for information only
and are not considered standard.
1.2 This test method extends the applicability of simulated
1.7 This standard does not purport to address all of the
distillation to samples that do not elute completely from the
safety concerns, if any, associated with its use. It is the
chromatographicsystem.Thistestmethodisusedtodetermine
responsibility of the user of this standard to establish appro-
the boiling point distribution through a temperature of 720°C.
priate safety, health, and environmental practices and deter-
This temperature corresponds to the elution of n-C .
100
mine the applicability of regulatory limitations prior to use.
1.3 Thistestmethodisusedforthedeterminationofboiling
Specific warning statements are given in Section 8.
point distribution of crude oils.This test method uses capillary
1.8 This international standard was developed in accor-
columns with thin films, which results in the incomplete
dance with internationally recognized principles on standard-
separationofC -C inthepresenceoflargeamountsofcarbon
4 8
ization established in the Decision on Principles for the
disulfide, and thus yields an unreliable boiling point distribu-
Development of International Standards, Guides and Recom-
tioncorrespondingtothiselutioninterval.Inaddition,quench-
mendations issued by the World Trade Organization Technical
ing of the response of the detector employed to hydrocarbons
Barriers to Trade (TBT) Committee.
eluting during carbon disulfide elution, results in unreliable
quantitative analysis of the boiling distribution in the C -C
4 8
2. Referenced Documents
region. Since the detector does not quantitatively measure the
2
2.1 ASTM Standards:
carbon disulfide, its subtraction from the sample using a
D2887Test Method for Boiling Range Distribution of Pe-
solvent-only injection and corrections to this region via
troleum Fractions by Gas Chromatography
quenching factors, results in an approximate determination of
D2892Test Method for Distillation of Crude Petroleum
thenetchromatographicarea.Aseparate,higherresolutiongas
(15-Theoretical Plate Column)
chromatograph (GC) analysis of the light end portion of the
D4057Practice for Manual Sampling of Petroleum and
sample may be necessary in order to obtain a more accurate
Petroleum Products
descriptionoftheboilingpointcurveintheintervalinquestion
D6352Test Method for Boiling Range Distribution of Pe-
as described in Test Method D7900 (see Appendix X1).
troleum Distillates in Boiling Range from 174°C to
1.4 This test method is also designed to obtain the boiling
700°C by Gas Chromatography
pointdistributionofotherincompletelyelutingsamplessuchas
D6299Practice for Applying Statistical Quality Assurance
atmospheric residues, vacuum residues, etc., that are charac-
and Control Charting Techniques to Evaluate Analytical
terized by the fact that the sample components are resolved
Measurement System Performance
from the solvent.
D7500Test Method for Determination of Boiling Range
Distribution of Distillates and Lubricating Base Oils—in
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
2
Subcommittee D02.04.0H on Chromatographic Distribution Methods. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2020. Published June 2020. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2005. Last previous edition approved in 2019 as D7169–19. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D7169-20. the ASTM website.
*A Summary of Changes section appears at the end of t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7169 − 19 D7169 − 20
Standard Test Method for
Boiling Point Distribution of Samples with Residues Such
as Crude Oils and Atmospheric and Vacuum Residues by
1
High Temperature Gas Chromatography
This standard is issued under the fixed designation D7169; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers the determination of the boiling point distribution and cut point intervals of crude oils and residues
by using high temperature gas chromatography. The amount of residue (or sample recovery) is determined using an external
standard.
1.2 This test method extends the applicability of simulated distillation to samples that do not elute completely from the
chromatographic system. This test method is used to determine the boiling point distribution through a temperature of 720 °C. This
temperature corresponds to the elution of n-C .
100
1.3 This test method is used for the determination of boiling point distribution of crude oils. This test method uses capillary
columns with thin films, which results in the incomplete separation of C -C in the presence of large amounts of carbon disulfide,
4 8
and thus yields an unreliable boiling point distribution corresponding to this elution interval. In addition, quenching of the response
of the detector employed to hydrocarbons eluting during carbon disulfide elution, results in unreliable quantitative analysis of the
boiling distribution in the C -C region. Since the detector does not quantitatively measure the carbon disulfide, its subtraction from
4 8
the sample using a solvent-only injection and corrections to this region via quenching factors, results in an approximate
determination of the net chromatographic area. A separate, higher resolution gas chromatograph (GC) analysis of the light end
portion of the sample may be necessary in order to obtain a more accurate description of the boiling point curve in the interval
in question as described in Test Method D7900 (see Appendix X1).
1.4 This test method is also designed to obtain the boiling point distribution of other incompletely eluting samples such as
atmospheric residues, vacuum residues, etc., that are characterized by the fact that the sample components are resolved from the
solvent.
1.5 This test method is not applicable for the analysis of materials containing a heterogeneous component such as polyesters
and polyolefins.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. Specific warning statements are given in Section 8.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D2887 Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.04.0H on Chromatographic Distribution Methods.
Current edition approved Dec. 1, 2019May 1, 2020. Published December 2019June 2020. Originally approved in 2005. Last previous edition approved in 20182019 as
D7169 – 18.D7169 – 19. DOI: 10.1520/D7169-19.10.1520/D7169-20.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United Sta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.