ASTM D3087-91(2004)
(Test Method)Standard Test Method for Operating Performance of Anion-Exchange Materials for Strong Acid Removal
Standard Test Method for Operating Performance of Anion-Exchange Materials for Strong Acid Removal
SIGNIFICANCE AND USE
This test method can be used for evaluating performance of commercially available anion-exchange materials regardless of the basic strength of the ion exchange groups. When previous operating history is known, a good interpretation of resin fouling or malfunction can be obtained by comparison against a reference sample of unused ion-exchange material evaluated in the same way.
While resistivity has been chosen as the preferred analytical method for defining the exhaustion end point, with titration as the alternative, it is understood that observation of pH during rinse and the service run can yield useful information. The variations in pH observed with an ion exchange material suspected of having degraded, can be helpful in interpretation of performance when compared with similar data for a reference sample of unused material exhausted in the same way.
SCOPE
1.1 This test method covers the determination of the operating capacity of anion-exchange materials when used for the removal of hydrochloric and sulfuric acid from water. It is designed to simulate operating conditions for strong acid removal and is intended for use in testing both new and used materials.
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 1.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D 3087–91(Reapproved 2004)
Standard Test Method for
Operating Performance of Anion-Exchange Materials for
Strong Acid Removal
This standard is issued under the fixed designation D 3087; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope the form of a bed in a transparent column. The exhaustion
medium used is an ion-exchange test water.
1.1 This test method covers the determination of the oper-
ating capacity of anion-exchange materials when used for the
5. Significance and Use
removal of hydrochloric and sulfuric acid from water. It is
5.1 Thistestmethodcanbeusedforevaluatingperformance
designed to simulate operating conditions for strong acid
of commercially available anion-exchange materials regardless
removal and is intended for use in testing both new and used
of the basic strength of the ion exchange groups. When
materials.
previous operating history is known, a good interpretation of
1.2 The values stated in SI units are to be regarded as the
resin fouling or malfunction can be obtained by comparison
standard. The inch-pound units given in parentheses are for
against a reference sample of unused ion-exchange material
information only.
evaluated in the same way.
1.3 This standard does not purport to address all of the
5.2 While resistivity has been chosen as the preferred
safety concerns, if any, associated with its use. It is the
analytical method for defining the exhaustion end point, with
responsibility of the user of this standard to establish appro-
titration as the alternative, it is understood that observation of
priate safety and health practices and determine the applica-
pH during rinse and the service run can yield useful informa-
bility of regulatory limitations prior to use. Specific precau-
tion. The variations in pH observed with an ion exchange
tionary statements are given in Note 1.
material suspected of having degraded, can be helpful in
2. Referenced Documents interpretationofperformancewhencomparedwithsimilardata
for a reference sample of unused material exhausted in the
2.1 ASTM Standards:
same way.
D 1067 Test Methods for Acidity or Alkalinity of Water
D 1125 Test Methods for Electrical Conductivity and Re-
6. Apparatus
sistivity of Water
6.1 Test Assembly (see Fig. 1), consisting of the following:
D 1129 Terminology Relating to Water
6.1.1 Column, transparent, vertically supported, 25.4 6
D 1193 Specification for Reagent Water
2.5-mm (1.0 6 0.1-in.) inside diameter and approximately 1.5
D 2687 Practices for Sampling Particulate Ion-Exchange
m (60 in.) long. The bottom of the column shall be closed and
Materials
provided with an outlet of approximately 6-mm ( ⁄4-in.) inside
3. Terminology diameter. Connections shall be provided at the top and bottom
for the admission and removal of the solutions described in
3.1 Definitions—For definitions of terms used in this test
Section 7. Adequate means for measuring and regulating the
method, refer to Terminology D 1129.
flow shall also be provided. The column shall be calibrated in
4. Summary of Test Method
suchamannerthatthevolumereadingsrequiredbythemethod
can be made (see Section 9). All measurements shall be made
4.1 The test method consists of repeated cycles of back-
at 25 6 5°C.
wash, base regeneration, rinse, and exhaustion of the sample in
6.1.2 Support the sample at least 50 mm (2 in.) above the
bottomofthecolumnoutletusingquartz,gravel,glassbeadsor
This test method is under the jurisdiction of ASTM Committee D19 on Water, 1 1
other material from 1.5 to 3.5 mm ( ⁄16 to ⁄8 in.) in diameter,
and is the direct responsibility of Subcommittee D19.08 on Membranes and Ion
Exchange Materials.
Current edition approved June 1, 2004. Published June 2004. Originally
approved in 1978. Last previous edition approved in 1998 as D 3087 – 91 (1998).
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D 3087–91 (2004)
D 1067, titrating to the methyl purple end point. The acidity
shall be 10.0 6 0.5 meq/L (epm).
7.5 Base Regenerants:
7.5.1 For Weak Base Ion-Exchange Materials:
7.5.1.1 Ammonium Hydroxide (40 g NH /L)—Dilute 155
mL of ammonium hydroxide (NH OH sp gr 0.90) to 1 L with
water. The solution should be freshly prepared to avoid
absorption of carbon dioxide (CO ) from the air.
7.5.2 For Weak, Intermediate, and Strong Base Ion-
Exchange Materials:
7.5.2.1 Sodium Hydroxide Solution (40 g/L)—Dissolve 40 g
of sodium hydroxide (NaOH) in 800 mLof water and dilute to
1 L. The solution should be freshly prepared to avoid absorp-
tion of carbon dioxide (CO ) from the air.
8. Sampling
8.1 For sampling procedures refer to Practices D 2687.
9. Procedure
9.1 Adjust temperature of the water and all solutions to be
used in this procedure to 25 6 5°C and maintain this
temperature throughout the test.
9.2 Fill the column approximately half full of water and add
sufficient sample to give a bed height of 750 6 75 mm (30 6
3 in.) above the top of the support. To avoid drying out of the
FIG. 1 Typical Arrangement of Apparatus for Performance Testing ion-exchange material, maintain a layer of liquid at least 20 to
of Ion-Exchange Materials
30 mm (0.8 to 1.2 in.) deep above the top of the bed at all times
during the procedure.
9.3 Backwash with water for 10 min using a flow rate that
insoluble in the reagents used, and retained on a corrosion-
resistant screen. However, other supports may be used at the will maintain a 50 % expansion of the bed. If the supernatant
liquid is clear at this point, proceed to 9.4. If the supernatant
discretion of the interested parties.
liquid is cloudy (indicating the presence of light, insoluble,
7. Reagents
extraneous material), adjust the backwash outlet tube to a
height above the bed equal to 75 % of the bed height. Continue
7.1 Purity of Reagents—Reagent grade chemicals shall be
backwashing at the same rate until the effluent is clear.
used in all tests. Unless otherwise indicated, it is intended that
all reagents shall conform to the specifications of the Commit-
9.4 Allow the bed to settle and then drain at a rate of
tee onAnalytical Reagents of theAmerican Chemical Society, approximately100mL/minuntilthewaterlevelis20to30mm
where such specifications are available. Other grades may be
(0.8 to 1.2 in.) above the top of the bed. Record the volume, in
used, provided it is first ascertained that the reagent is of millilitres, of ion-exchange material for use in the following
sufficiently high puritity to permit its use without lessening the
pretreatment. Regenerate the sample with the appropriate
accuracy of the determination. dilute sodium hydroxide solution (see Note 2) for 90 min at a
7.2 Purity of Water— Unless otherwise indicated, refer-
flow rate of 0.11 mL/min for each millilitre of ion exchanger in
ences to water shall be understood to mean reagent water thecolumn.Thiscorrespondstoaregenerationlevelof400g/L
conforming to Specification D 1193, Type III. (25 lb/ft ) of ion exchange material.
7.3 Acidity Test Reagents—For reagents used in determin-
9.5 When only a 20 to 30-mm (0.8 to 1.2-in.) layer of liquid
ing acidity, refer to Test Methods D 1067.
remains above the bed, rinse with water using the same flow
7.4 Anion Exchange Test Water C (10 meq/L)—Carefully
rate, until a volume equal to the volume of resin has been
add 18.1 mL of sulfuric acid (H SO , sp gr 1.84) and 27.5 mL
2 4 displaced (one bed volume). Increase the rinse rate to approx
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.