iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5519-07

(Test Method)

Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials

Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials

SIGNIFICANCE AND USE
Riprap is commonly used to prevent erosion of underlying materials due to the effects of rain runoff, wind, flowing water, or wave action. The particle size distribution (mass of particles) is an important physical characteristic of riprap, as discussed in D 6825. These test methods provide a gradation of the material graphically represented as percent finer than the particle mass. If a gradation can be established or accepted on the basis of only maximum and minimum particle sizes, then it may not be necessary to establish the complete gradation in accordance with these test methods.
These test methods can be used during evaluation of a potential source, as a means of product acceptance, or for assessment of existing installations. Method D is not recommended as a means of product acceptance.
Other characteristics of interest, such as particle shape, particle angularity, or visually evident rock durability characteristics may be determined during the performance of these test methods.
Interpretation of test results must consider the representativeness of the sample.
Note 2—The agency performing these test methods can be evaluated in accordance with Practice D 3740. Not withstanding statements on precision and bias contained in these test methods: The precision of these test methods is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing. Users of these test methods are cautioned that compliance with Practice D 3740 does not in itself ensure reliable testing. Reliable testing depends on many factors; Practice D 3740 provides a means of evaluating some of those factors.
SCOPE
1.1 These test methods cover the particle size and mass analysis of natural and man-made riprap and related materials, including filter stone or coarse bedding materials.
1.2 These test methods are generally intended for riprap and related materials. They are applicable for mixtures of stones screened from natural deposits, blast rock, processed materials from quarried rock, or recycled concrete. They are applicable for sizes 3 in. (75 mm) and above, with the upper size limited only by equipment available for handling and weighing the individual particles.
1.3 Four alternate procedures are provided. There is a wide range in the level of effort and the precision of the test procedures. It is important for specifiers to indicate the test procedure. Test reports should clearly indicate which procedure was used.Note 1
While conducting these test methods, it may be convenient to collect data on other attributes, such as the amount of slab pieces and deleterious materials.
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026
1.5 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units given in parentheses may be approximate.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

General Information

Status
Historical
Publication Date
30-Jun-2007
ICS
19.120 - Particle size analysis. Sieving
Technical Committee
D18 - Soil and Rock
Drafting Committee
D18.17 - Rock for Erosion Control
Current Stage
Ref Project

Relations

Replaces
ASTM D5519-94(2001) - Standard Test Method for Particle Size Analysis of Natural and Man-Made Riprap Materials
Effective Date
01-Jul-2007
Replaced By
ASTM D5519-14 - Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials
Effective Date
01-Nov-2014
Referred By
ASTM D6711/D6711M-22 - Standard Practice for Specifying Rock to Fill Gabions, Revet Mattresses, and Gabion Mattresses
Effective Date
01-Jul-2007
Referred By
ASTM D6913/D6913M-17 - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
Effective Date
01-Jul-2007
Referred By
ASTM D6825-21 - Standard Guide for Placement of Riprap Revetments
Effective Date
01-Jul-2007
Referred By
ASTM D6092-21 - Standard Practice for Specifying Standard Sizes of Stone for Erosion Control
Effective Date
01-Jul-2007

Buy Standard

ASTM D5519-07 - Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap MaterialsASTM D5519-07 - Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials
PreviousNext
Standard
ASTM D5519-07 - Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5519 − 07
StandardTest Methods for
Particle Size Analysis of Natural and Man-Made Riprap
1
Materials
This standard is issued under the fixed designation D5519; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 These test methods cover the particle size and mass 2.1 ASTM Standards:
analysis of natural and man-made riprap and related materials, C136 Test Method for Sieve Analysis of Fine and Coarse
including filter stone or coarse bedding materials. Aggregates
D422 Test Method for Particle-Size Analysis of Soils
1.2 These test methods are generally intended for riprap and
D653 Terminology Relating to Soil, Rock, and Contained
related materials. They are applicable for mixtures of stones
Fluids
screened from natural deposits, blast rock, processed materials
D3740 Practice for Minimum Requirements for Agencies
from quarried rock, or recycled concrete. They are applicable
Engaged in Testing and/or Inspection of Soil and Rock as
for sizes 3 in. (75 mm) and above, with the upper size limited
Used in Engineering Design and Construction
only by equipment available for handling and weighing the
D4992 Practice for Evaluation of Rock to be Used for
individual particles.
Erosion Control
1.3 Four alternate procedures are provided. There is a wide
D5240 Test Method for Testing Rock Slabs to Evaluate
range in the level of effort and the precision of the test
Soundness of Riprap by Use of Sodium Sulfate or
procedures. It is important for specifiers to indicate the test
Magnesium Sulfate
procedure.Testreportsshouldclearlyindicatewhichprocedure
D5312 Test Method for Evaluation of Durability of Rock for
was used.
Erosion Control Under Freezing and Thawing Conditions
NOTE 1—While conducting these test methods, it may be convenient to
D5313 Test Method for Evaluation of Durability of Rock for
collect data on other attributes, such as the amount of slab pieces and
Erosion Control Under Wetting and Drying Conditions
deleterious materials.
D6026 Practice for Using Significant Digits in Geotechnical
1.4 All observed and calculated values shall conform to the
Data
guidelines for significant digits and rounding established in
D6825 Guide for Placement of Riprap Revetments
Practice D6026
E11 Specification for Woven Wire Test Sieve Cloth and Test
1.5 The values stated in inch-pound units are to be regarded
Sieves
as the standard. The metric equivalents of inch-pound units
3. Terminology
given in parentheses may be approximate.
1.6 This standard does not purport to address all of the 3.1 Definitions:
safety concerns, if any, associated with its use. It is the 3.1.1 Terminology used within these test methods is in
responsibility of the user of this standard to establish appro- accordance with Terminology D653 with the addition of the
priate safety and health practices and determine the applica- following:
bility of regulatory limitations prior to use. Specific precau- 3.2 Definitions of Terms Specific to This Standard:
tionary statements are given in Section 7. 3.2.1 bedding (riprap)—an aggregate mixture placed below
the riprap. (See D6825 for further information.)
1
These test methods are under the jurisdiction ofASTM Committee D18 on Soil
and Rock and are the direct responsibility of Subcommittee D18.17 on Rock for
2
Erosion Control. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved July 1, 2007. Published August 2007. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1994. Last previous edition approved in 2001 as D5519 – 94 (2001). Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/D5519-07. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5519 − 07
testing. Reliable testing depends on many factors; Practice D3740
3.2.2 slab pieces—pieces of riprap that exhibit dimensional
provides a means of evaluating some of those factors.
ratios of the thickness to width or width to length, or both, in
excess of a specified ratio. The specified ratios typically range
6. Apparatus
from 1:4 to 1:3 or less.
6.1 Scales, of adequate capacity to determine the mass of
thesortedriprappieceseitherindividuallyorinwhole.ForTest
4. Summary of Test Method
MethodA(or calibrations forTest Methods B and C), the scale
4.1 The following four test methods for evaluating parti
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8200-22(Practice)
Standard Practice for Creating a Correlation to Compare Particle Size Distribution Results of Proppants by Dynamic Imaging Analyzers and Sieves

SIGNIFICANCE AND USE
5.1 The ability to correlate results of analyzers to sieve sets enables the use of non-sieve methods to be employed that give comparable results to each other.  
5.2 The use of analyzers for proppant measurement has the benefit of providing particle shape characteristics which are important in the performance of these materials. Shape analysis is currently done by operator’s determination based on a visual observation of a small number of particles per API 19C. Available information from imaging analysis of many particles can be used to assess the proppant shape characteristics as opposed to just a small number.
SCOPE
1.1 This practice describes procedural steps to create a correlation that can be used to compare results of proppant size distributions between dynamic imaging analyzers (analyzers) and prescribed sieve sets.  
1.2 The proppant size and distribution specifications that are included in this practice are listed in API Standard 19C (API 19C) and shown in Table 1, however as industry evolves additional specifications may come into use and this practice can be used with those as well.  
1.3 This practice may not be applicable to all proppant types and designations. The acceptability of the correlations determined are judged by the operator.  
1.4 The values stated in SI units are to be regarded as the standard, except sieve designations are typically identified using the ‘alternative’ system in accordance with Practice E11, such as 3 in. and No. 200 instead of the ‘standard’ system of 75 mm and 75 µm, respectively.  
1.5 Observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard.  
1.5.1 The procedures used to specify how data are collected/recorded and calculated in Practice D6026 are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.  
1.6 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2977-22(Practice)
Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes

SIGNIFICANCE AND USE
5.1 This practice is primarily used in the horticulture industry to separates peat material into arbitrary fractions based on particle size. Physical separation of peat material according to particle size provides a useful indicator of the properties of a peat specimen such as pore space and degree of decomposition for unprocessed peat. It also provides a means of determining the amount of foreign matter not in a divided state such as sticks, stones, and glass.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 Peat materials consist of particles with various sizes. This practice covers the separation of peat particles into coarse, medium, and fine size fractions using the 2.36 mm (No. 8) and 0.850 mm (No. 20) sieves equipped with cover and bottom pan. This practice is applicable for peat materials used in the horticultural industry and can be used to verify the degree of decomposition of peat and to determine the foreign matter content.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.2.1 It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This practice implicitly combines two separate systems of units; the absolute and the gravitational systems. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit of mass. However, the use of balances and scales recording pounds of mass (lbm) or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard.  
1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.3.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.5 This standard does not purport to address all of the safety concerns, if any...

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8123-22(Test Method)
Standard Test Methods for Measuring the Opening Size of Geohazard Nettings

SIGNIFICANCE AND USE
5.1 Using a geohazard netting as a medium to retain rock particles necessitates compatibility between it and the adjacent rock. These test methods measure the opening size of a geohazard netting which may be used to estimate the largest size of rocks or other objects that may pass through the geohazard netting without transferring load to the wire mesh or wire net.  
5.2 These test methods may be applied to other components of the geohazard netting, such as regularly spaced reinforcement elements or secondary mesh openings.  
5.3 These test methods may also be used for quality control during the manufacturing process and quality assurance that materials supplied conform to project or material specifications.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 These test methods are index tests to measure the opening size of a geohazard netting, or its components, or both, as it has been manufactured. They can be used for estimating the largest size of rock or other object that may pass through an individual opening in the geohazard netting without transferring load to the wire mesh or wire net and may also be used for quality control purposes. These test methods are not used to determine the maximum size rock or other object that the geohazard netting may contain through mobilization of the netting’s strength. These test methods do not apply to the measurement of the opening size of a geosynthetic, such as a turf reinforcement mat or geotextile, that may be manufactured as a composite system with the geohazard netting.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.3.1 For purposes of comparing a measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal of significant digits in the specified limit.  
1.3.2 The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objective; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT...

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6393/D6393M-21(Test Method)
Standard Test Method for Bulk Solids Characterization by Carr Indices

SIGNIFICANCE AND USE
5.1 This test method provides measurements that can be used to describe the bulk properties of a powder or granular material.  
5.2 The measurements can be combined with practical experience to provide relative rankings of various forms of bulk handling behavior of powders and granular materials for a specific application.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors. Practice D3740 was developed for agencies engaged in the testing or inspection (or both) of soil and rock. As such it is not totally applicable to agencies performing this standard. However, users of this standard should recognize that the framework of Practice D3740 is appropriate for evaluating the quality of an agency performing this standard. Currently there is no known qualifying national authority that inspects agencies that perform this standard.
SCOPE
1.1 This test method covers an apparatus and procedures for measuring properties of bulk solids, henceforth referred to as Carr Indices.2  
1.2 This test method is suitable for free flowing and moderately cohesive powders and granular materials up to 2.0 mm [1/16 in.] in size. Materials must be able to pour through a 6.0 to 8.0-mm [1/4 to 5/16 in.] diameter funnel outlet when in an aerated state.  
1.3 This method consists of eight measurements and two calculations for Carr Indices as follows. Each measurement, or calculation, or combination of them, can be used to characterize the properties of bulk solids.  
1.3.1 Measurement of Carr Angle of Repose  
1.3.2 Measurement of Carr Angle of Fall  
1.3.3 Calculation of Carr Angle of Difference  
1.3.4 Measurement of Carr Loose Bulk Density  
1.3.5 Measurement of Carr Packed Bulk Density  
1.3.6 Calculation of Carr Compressibility  
1.3.7 Measurement of Carr Cohesion  
1.3.8 Measurement of Carr Uniformity  
1.3.9 Measurement of Carr Angle of Spatula  
1.3.10 Measurement of Carr Dispersibility  
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.4.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives: and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on st...

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D6940/D6940M-20(Practice)
Standard Practice for Measuring Sifting Segregation Tendencies of Bulk Solids

SIGNIFICANCE AND USE
5.1 Sifting segregation can cause horizontal segregation (for example, center-to-periphery) within bins used to hold and transport bulk solids. This can affect final product quality or subsequent processes in industrial applications.  
5.2 By measuring a bulk solid's segregation tendency, one can compare results to other bulk solids with known history, or determine if the given bulk solid may have a tendency to segregate in a given process.  
5.3 Sifting, which is a process by which smaller particles move through a matrix of larger ones, is a common method of segregation. Four conditions must exist for sifting to occur:  
5.3.1 A Difference in Particle Size between the Individual Components—This ratio can be as low as 1.3 to 1. In general, the larger the ratio of particle sizes, the greater the tendency for particles to segregate by sifting.  
5.3.2 A Sufficiently Large Mean Particle Size—Sifting segregation can occur with a mean particle size in the 50 μm range and can become a dominant segregation mechanism if the mean particle size is above 100 μm.  
5.3.3 Sufficiently Free Flowing Material—This allows the smaller particles to sift through the matrix of larger particles. With cohesive materials, the fine particles are bound to one another and do not enter the voids among the coarse particles.  
5.3.4 Interparticle Motion—This can be caused during formation of a pile, by vibration, or by a velocity gradient across the flowing material.  
5.4 All four of these conditions must exist for sifting segregation to occur. If any one of these conditions does not exist, the material will not segregate by this mechanism.
Note 1: The quality of the result produced by this practice is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this practice are ...
SCOPE
1.1 This practice covers an apparatus and procedure for simulating the segregation tendencies of bulk solids by means of the sifting mechanism.  
1.2 Temperature- and humidity-sensitive bulk solids may need to be tested at different temperatures and moisture contents, as would happen in an industrial environment.  
1.3 The maximum particle size should be limited to 3 mm [1/8 in.], to reduce the likelihood of binding the slide gate.  
1.4 This standard is not applicable to all bulk solids and segregation mechanisms: while sifting is a common segregation mechanism experienced by many bulk solids, other segregation mechanisms not evaluated by this standard might induce segregation in practice. Practice D6941 covers another common mechanism: fluidization.  
1.5 The extent to which segregation will occur in an industrial situation is not only a function of the bulk solid and its tendency to segregate, but also the handling equipment (for example, bin design), process (for example, transfer rates), and environment.  
1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.7 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.8 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this docum...

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6941-19(Practice)
Standard Practice for Measuring Fluidization Segregation Tendencies of Powders

SIGNIFICANCE AND USE
5.1 Fluidization segregation can cause vertical segregation within bins used to hold and transport powders. This can affect product quality or subsequent processes in industrial applications.  
5.2 By measuring a powder's segregation tendency, one can compare results to other powders with known history, or determine if the given powder may have a tendency to segregate in a given process.  
5.3 Fine powders generally have a lower permeability than coarse bulk solids and therefore tend to retain air longer. Thus, when a bin is filled with a fluidizable powder, the coarser particles settle or are driven into the bed while the finer particles remain fluidized near the surface.  
5.4 Fluidization, which serves as a driving force for this mechanism of segregation, is likely to occur when fine powders are pneumatically conveyed into a bin, the bin is filled or discharged at high rates, or if sufficient air flow counter to the flow of powder is present within the bin.
Note 1: The quality of the result produced by this practice is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this practice are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
Practice D3740 was developed for agencies engaged in the testing and/or inspection of soil and rock. As such it is not totally applicable to agencies performing this practice. However, users of this practice should recognize that the framework of Practice D3740 is appropriate for evaluating the quality of an agency performing this practice. Currently there is no known qualifying national authority that inspects agencies that perform this practice.
SCOPE
1.1 This practice covers an apparatus and procedure for creating several specimens of a powder sample that, if the powder is one that segregates by the fluidization mechanism, should be different from one another.  
1.2 A powder sample is fluidized then, after the fluidizing gas is turned off, it is separated into three or more specimens that can be analyzed for parameters of interest. The difference in these parameters between the specimens is an indication of the segregation potential of the powder.  
1.3 Powders must be capable of being fluidized in order to be tested by this practice.  
1.4 Temperature- and moisture-sensitive powders may need to be tested at different temperatures and moisture contents, as would happen in an industrial environment.  
1.5 This standard is not applicable to all bulk solids and segregation mechanisms: while fluidization is a common segregation mechanism experienced by many fine powders, other segregation mechanisms not evaluated by this standard might induce segregation in practice. Practice D6940 covers another common mechanism: sifting.  
1.6 The extent to which segregation will occur in an industrial situation is not only a function of the powder and its tendency to segregate, but also the handling equipment (for example, bin design), process (for example, transfer rates), and environment.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consid...

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6683-19(Test Method)
Standard Test Method for Measuring Bulk Density Values of Powders and Other Bulk Solids as Function of Compressive Stress

SIGNIFICANCE AND USE
5.1 The data from this test can be used to estimate the bulk density of materials in bins and hoppers and for material handling applications such as feeders.  
5.2 The test results can be greatly affected by the sample selected for testing. For meaningful results it is necessary to select a representative sample of the particulate solid with respect to moisture (water) content, particle-size distribution and temperature. For the tests an appropriate size sample should be available, and fresh material should be used for each individual test specimen.  
5.3 Initial bulk density, (ρb)initial, may or may not be used as the minimum bulk density. This will depend on the material being tested. For example, the two are often close to the same for coarse (most particles larger than about 6 mm), free-flowing bulk solids, but not for fine, aeratable powders.  
5.4 Bulk density values may be dependent upon the magnitude of the applied mass increments. Traditionally, the applied mass is doubled for each increment resulting in an applied mass increment ratio of 1. Smaller than standard increment ratios may be desirable for materials that are highly sensitive to the applied mass increment ratio. An example of the latter is a material whose bulk density increases 10% or more with each increase in applied mass.  
5.5 Bulk density values may be dependent upon the duration of each applied mass. Traditionally, the duration is the same for each increment and equal to 15 s. For some materials, the rate of compression is such that complete compression (no change in volume with time at a given applied compressive stress) will require significantly more than 15 s.
Note 1: The quality of the result produced by this standard is dependent on the competence of personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users ...
SCOPE
1.1 This test method covers an apparatus and procedure for determining a range of bulk densities of powders and other bulk solids as a function of compressive stress.  
1.2 This test method should be performed in the laboratory under controlled conditions of temperature and humidity.  
1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.3.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives, and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measure are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D1140-17(Test Method)
Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing

SIGNIFICANCE AND USE
5.1 Material finer than the 75-μm (No. 200) sieve can be separated from larger particles or soil aggregations can be broken down much more efficiently and completely by wet sieving than with dry sieving. Therefore, when accurate determinations of material finer than a 75-μm (No. 200) sieve are desired, these test methods are used on the test specimen prior to dry sieving, or as a determination of the percent of material that is finer than a 75-μm (No. 200) sieve. Usually the additional amount of material finer than a 75-μm (No. 200) sieve obtained in the dry sieving process is a small amount. If it is large, the efficiency of the washing operation should be checked, as it could be an indication of degradation of the soil (see Note 2).  
5.2 Method A shall be used with non-cohesive soils containing fine material with little or no plasticity. The specimen is soaked in water to facilitate the separation of the fine and coarse fractions prior to washing through the 75-μm (No. 200) sieve.  
5.3 Method B shall be used with soils, particularly clayey soils, where the fine material demonstrates plastic behavior and tends to adhere to the larger particles. To provide adequate fine grain dispersal, it is necessary to soak the specimen in a dispersing solution prior to washing through the 75-μm (No. 200) sieve.  
5.4 To facilitate determination of which method to utilize, the sample may be classified as non-cohesive or having plastic characteristics based upon procedures outlined in Practice D2488 or other means of determining the soil properties.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself ensure reliable ...
SCOPE
1.1 These test methods cover the determination of the amount of material finer than a 75-μm (No. 200) sieve by washing of material with a maximum particle size of 75 mm (3 in.).  
1.2 The methods used in this standard rely on the use of water or a dispersant to separate and remove materials finer than a 75-μm (No. 200) sieve. During these processes soluble substances, such as salts and other minerals, may also be removed. It is not within the scope of this standard to differentiate between the removal of fine particles and soluble substances. It is recommended that materials containing significant amounts of soluble substances be tested using other methods of separation.  
1.3 Two methods for determining the amount of material finer than the 75-μm (No. 200) sieve are provided. The method to be used shall be specified by the requesting authority. If no method is specified, the choice should be based upon the guidance given in 5.2, 5.3, and 5.4.  
1.3.1 Method A—Test specimen is dispersed by soaking in water prior to wash sieving.  
1.3.2 Method B—Test specimen is dispersed by soaking in a dispersing solution prior to wash sieving.  
1.4 Units—The values stated in SI units are to be regarded as standard. Except the sieve designations are typically identified using the “alternative” system in accordance with Specification E11, such as 3 inch and No. 200, instead of the “standard” of 75-mm and 75-μm, respectively. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. The use of balances or scales recording pounds of mass (lbm) shall not be regarded as nonconformance with this standard.  
1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.  
1.5.1 The procedures used to specify how data are collected/recorded and calculated in this standa...

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5519-15(Test Method)
Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials

SIGNIFICANCE AND USE
5.1 Riprap is commonly used to prevent erosion of underlying materials due to the effects of rain runoff, wind, flowing water, or wave action. The particle size distribution (mass of particles) is an important physical characteristic of riprap, as discussed in Guide D6825. These test methods provide a gradation of the material graphically represented as percent finer than the particle mass. If a gradation can be established or accepted on the basis of only maximum and minimum particle sizes, then it may not be necessary to establish the complete gradation in accordance with these test methods.  
5.2 These test methods can be used during evaluation of a potential source, as a means of product acceptance, or for assessment of existing installations. Method D is not recommended as a means of product acceptance.  
5.3 Other characteristics of interest, such as particle shape, particle angularity, or visually evident rock durability characteristics may be determined during the performance of these test methods.  
5.4 Interpretation of test results must consider the representativeness of the sample.
Note 2: The quality of the result produced by this standard is dependent upon the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself ensure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 These test methods cover the particle size and mass analysis of natural and man-made riprap and related materials, including filter stone or coarse bedding materials.  
1.2 These test methods are generally intended for riprap and related materials. They are applicable for mixtures of stones screened from natural deposits, blast rock, processed materials from quarried rock, or recycled concrete. They are applicable for sizes 3 in. (75 mm) and above, with the upper size limited only by equipment available for handling and determining the mass of the individual particles.  
1.3 Four alternate procedures are provided. There is a wide range in the level of effort and the precision of the test procedures. It is important for specifiers to indicate the test procedure. Test reports should clearly indicate which procedure was used.
Note 1: While conducting these test methods, it may be convenient to collect data on other attributes, such as the amount of slab pieces and deleterious materials.  
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard.  
1.4.1 For purposes of comparing measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits.  
1.4.2 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5.1 Th...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D7891-15(Test Method)
Standard Test Method for Shear Testing of Powders Using the Freeman Technology FT4 Powder Rheometer Shear Cell

SIGNIFICANCE AND USE
5.1 The test can be used to evaluate the following:  
5.1.1 Classification or Comparison of Powders—There are several parameters that can be used to classify powders relative to each other, the most useful being the measured shear stresses, cohesion, flow function and angle of internal friction.  
5.1.2 Sensitivity Analysis—The shear cell can be used to evaluate the relative effects of a range of powder properties and/or environmental parameters such as (but not limited to) humidity, particle size and size distribution, particle shape and shape distribution, moisture content and temperature.  
5.1.3 Quality Control—The test can, in some circumstances, be used to assess the flow properties of a raw material, intermediate or product against pre-determined acceptance criteria.  
5.1.4 Storage Vessel Design—Mathematical models exist for the determination of storage vessel design parameters which are based on the flow properties of powders as generated by shear cell testing, requiring shear testing at a range of consolidating stresses as well as the measurement of the wall friction angle with respect to the material of construction of the storage vessel. The methods are detailed in Refs. (1-3).2
Note 1: The quality of the result produced by this test method is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this test method are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors (4).
Practice D3740 was developed for agencies engaged in the testing and/or inspection of soil and rock. As such it is not totally applicable to agencies performing this test method. However, users of this test method shou...
SCOPE
1.1 This method covers the apparatus and procedures for measuring the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation. The method also allows the further determination of the unconfined yield strength, internal friction angles, cohesion, flow function, major principal stress and wall friction angle (with the appropriate wall coupon fitted to the correct accessory).  
1.2 These parameters are most commonly used for the design of storage hoppers and bins using industry standard calculations and procedures. They can also provide relative classification or comparison of the flow behavior of different powders or different batches of the same powder if similar stress and shear regimes are encountered within the processing equipment.  
1.3 The apparatus is suitable for measuring the properties of powders with a maximum particle size of 1 mm. It is possible to test powders which have a small proportion of particles of 1 mm or greater, but they should be present in the bulk sample as no more than 5 % of the total mass in samples with a normal (Gaussian) size distribution.  
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.4.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.5 Units—Th...

  • Standard
    11 pages
    English language
    sale 15% off