iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E726-01(2006)

(Test Method)

Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides

Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides

SIGNIFICANCE AND USE
This procedure was designed principally for clay, corncob, nut shell paper, or sand granular carriers and granular pesticide products, but need not be limited to these materials. There may be more appropriate test methods for other types of granular carriers and products.
SCOPE
1.1 This test method is used to determine the particle size distribution of granular carriers and granular pesticides.  
1.2  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  For specific hazard statements, see Section 6.

General Information

Status
Historical
Publication Date
31-Oct-2006
ICS
19.120 - Particle size analysis. Sieving
Technical Committee
E35 - Pesticides, Antimicrobials, and Alternative Control Agents
Drafting Committee
E35.22 - Pesticide Formulations and Delivery Systems
Current Stage
Ref Project

Relations

Replaces
ASTM E726-01 - Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides
Effective Date
01-Nov-2006
Replaced By
ASTM E726-01(2011)e1 - Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides
Effective Date
01-Aug-2011
Referred By
ASTM E1520-23 - Standard Test Method for Particle Counts Per Pound of Granular Carriers and Dry-Applied Granular Formulations
Effective Date
01-Nov-2006
Referred By
ASTM E642-19 - Standard Practice for Determining Application Rates and Distribution Patterns from Aerial Application Equipment
Effective Date
01-Nov-2006

Buy Standard

ASTM E726-01(2006) - Standard Test Method for Particle Size Distribution of Granular Carriers and Granular PesticidesASTM E726-01(2006) - Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides
PreviousNext
Standard
ASTM E726-01(2006) - Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E726–01 (Reapproved 2006)
Standard Test Method for
Particle Size Distribution of Granular Carriers and Granular
Pesticides
This standard is issued under the fixed designation E726; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope There may be more appropriate test methods for other types of
granular carriers and products.
1.1 This test method is used to determine the particle size
distribution of granular carriers and granular pesticides.
5. Apparatus
1.2 This standard does not purport to address all of the
5.1 Brushes; Tyler Part No. 8576 soft brass wire brush, or
safety concerns, if any, associated with its use. It is the
equivalent, for 100 mesh (150 µm) and coarser sieves. Tyler
responsibility of the user of this standard to establish appro-
nylon bristle brush (Part No. 8577), or equivalent, for screens
priate safety and health practices and determine the applica-
finer than 100 mesh.
bility of regulatory limitations prior to use. For specific hazard
5.2 Mechanical Sieve Shaker; a Tyler RoTap sieve shaker,
statements, see Section 6.
or equivalent, or other agreed upon device.
2. Referenced Documents 5.3 Sieves; U.S. standard 8-in. (20.3 cm) diameter sieves,
or equivalent, conforming to Specification E11.
2.1 ASTM Standards:
5.4 Bottom Receiver Pan and Top Sieve Cover.
E11 SpecificationforWovenWireTestSieveClothandTest
5.5 Interval Timer; adjustable, with an accuracy of 610 s.
Sieves
5.6 Balance; sensitivity of 0.1 g.
E725 Test Method for Sampling Granular Carriers and
Granular Pesticides
6. Hazards
3. Summary of Test Method 6.1 Before testing, read the precautionary statements on the
productlabel,andtheMaterialSafetyDataSheet,orboth.Take
3.1 A known weight of the granular carrier or granular
proper precautions to prevent skin contact and inhalation of the
pesticide is placed on the top sieve of a stacked set of U.S.
fines, or the vapors, or both. Take care to prevent contamina-
standard sieves and shaken under standard conditions for a
tion of the surrounding area. Always wear the appropriate
specified period of time. The weight percent of the granules
safety equipment and, where indicated, wear respiratory de-
retained on each sieve and the bottom pan is determined.
vices approved by NIOSH for the product being tested.
4. Significance and Use
7. Procedure
4.1 This procedure was designed principally for clay, corn-
7.1 Clean and stack the specified sieves in order of size with
cob, nut shell paper, or sand granular carriers and granular
the pan on the bottom, and the sieve with the largest mesh on
pesticide products, but need not be limited to these materials.
the top.
7.2 Use a representative sample of approximately 10065g
This test method is under the jurisdiction of ASTM Committee E35 on
as defined in Test Method E725.
Pesticides and Alternative Control Agents and is the direct responsibility of
7.3 Weigh the sample to 60.1 g.
Subcommittee E35.22 on Pesticide Formulations and Delivery Systems.
7.4 Transfer the whole weighed fraction onto t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E726-01(2021)(Test Method)
Standard Test Method for Particle Size Distribution of Granular Carriers and Granular Pesticides

SIGNIFICANCE AND USE
4.1 This procedure was designed principally for clay, corncob, nut shell, paper, or sand granular carriers and granular pesticide products, but need not be limited to these materials. There may be more appropriate test methods for other types of granular carriers and products.
SCOPE
1.1 This test method is used to determine the particle size distribution of granular carriers and granular pesticides.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7891-24(Test Method)
Standard Test Method for Shear Testing of Powders Using the Freeman Technology FT4 Powder Rheometer Shear Cell

SIGNIFICANCE AND USE
5.1 The test can be used to evaluate the following:  
5.1.1 Classification or Comparison of Powders—There are several parameters that can be used to classify powders relative to each other, the most useful being the measured shear stresses, cohesion, flow function and angle of internal friction.  
5.1.2 Sensitivity Analysis—The shear cell can be used to evaluate the relative effects of a range of powder properties or environmental parameters, or both, such as (but not limited to) humidity, particle size and size distribution, particle shape and shape distribution, water content and temperature.  
5.2 Quality Control—The test can, in some circumstances, be used to assess the flow properties of a raw material, intermediate or product against pre-determined acceptance criteria.  
5.3 Storage Vessel Design—Mathematical models exist for the determination of storage vessel design parameters which are based on the flow properties of powders as generated by shear cell testing, requiring shear testing at a range of consolidating stresses as well as the measurement of the wall friction angle with respect to the material of construction of the storage vessel. The methods are detailed in Refs. (1-3).3
Note 1: The quality of the result produced by this test method is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this test method are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors (4).
Practice D3740 was developed for agencies engaged in the testing and/or inspection of soil and rock. As such it is not totally applicable to agencies performing this test method. However, users of this test method shoul...
SCOPE
1.1 This method covers the apparatus and procedures for quantifying the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation. The method also allows the further determination of the unconfined yield strength, internal friction angles, cohesion, flow function, major principal stress and wall friction angle (with the appropriate wall coupon fitted to the correct accessory).  
1.2 These parameters are most commonly used to assist with the design of storage hoppers and bins using industry standard calculations and procedures. They can also provide relative classification or comparison of the flow behavior of different powders or different batches of the same powder if similar stress and shear regimes are encountered within the processing equipment.  
1.3 The apparatus is appropriate for measuring the properties of powders with a maximum particle size of 1 mm. It is practicable to test powders that have a small proportion of particles of 1 mm or greater, but it is recommended they represent no more than 5 % of the total mass in samples with a normal (Gaussian) size distribution.  
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.  
1.4.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.  
1.5 Un...

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D4438-24(Test Method)
Standard Test Method for Particle Size Distribution of Catalysts and Catalyst Carriers by Electronic Counting

SIGNIFICANCE AND USE
4.1 This test method can be used to determine particle size distributions for material specifications, manufacturing control, and research and development work in the particle size range usually encountered in fluidizable cracking catalysts.
SCOPE
1.1 This test method covers the determination of particle size distribution of catalyst and catalyst carrier (see Terminology D3766) particles using an electroconductive sensing method and is one of several valuable methods for the measurement of particle size.  
1.2 The range of particle sizes investigated was 20 μm to 150 μm (see IEEE/ASTM SI 10) equivalent spherical diameter. The technique is capable of measuring particles above and below this range. The instrument used for this method is an electric current path of small dimensions that is modulated by individual particle passage through an aperture, and produces individual pulses of amplitude proportional to the particle volume.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1617-09(2024)(Practice)
Standard Practice for Reporting Particle Size Characterization Data

SIGNIFICANCE AND USE
3.1 When evaluating the particle size information, if the procedures of the data processing are not available, the user of the data must make assumptions concerning the reported data in the event of analytical inconsistencies. In order for different data sets to be compared it is crucial that the parties report the analytical techniques and methods or procedures for evaluating, calculating, compiling or otherwise processing the data to be reported.  
3.2 Particle size characterization information can be reported in three levels of detail in order to satisfy user's needs.  
3.2.1 Level 1 applies when only basic information about the material is required, and shall be provided with each shipment. This level represents the minimum information that shall be reported. Level 1 information may be sufficient in such cases as identifying a certain grade of a material or when detailed knowledge of analytical methodology is not needed.  
3.2.2 Level 2 presumes the need for knowledge of methodology on the user's part and allows the user to make a more informed judgment about the information provided in Level 1.  
3.2.3 Level 3 provides detailed written procedures to allow duplication of the measurement.  
3.2.4 Information provided through Levels 2 and 3 will allow users to perform comparative material evaluations among several suppliers, set specifications or define a purchase agreement, perform inter-laboratory studies and most importantly resolve disputes among suppliers and users.  
3.3 Reported particle size measurement is a function of both the actual particle dimension and shape factor as well as the particular physical or chemical properties of the particle being measured. Caution is required when comparing data from instruments operating on different physical or chemical parameters or with different particle size measurement ranges. Sample acquisition, handling and preparation can also affect the reported particle size results.
SCOPE
1.1 This practice covers reporting particle size measurement data.  
1.2 This practice applies to particle size measurement methods, devices, detail levels, and data formats for dry powders, and wet suspensions of solids, gels, or emulsion droplets. This practice does not pertain to liquid particles.  
Note 1: For information on reporting liquid particle measurement data, refer to Practice E799.  
1.3 This practice does not concern particle concentration information.  
1.4 This practice uses SI (Système International) units as standard. State all numerical values in terms of SI units unless specific instrumentation software reports particle size information, including percentiles, indices, and distributions as tabulations and graphs using alternate units. In this case, present both reported and equivalent SI units in the final written report. Refer to Practice E380 for proper usage of SI units.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E2589-23a(Terminology)
Standard Terminology Relating to Nonsieving Methods of Powder Characterization

SIGNIFICANCE AND USE
3.1 Interpretation and use of data generated by particle characterization methods is highly dependent on the definitions of terms describing that data. It is extremely important that those terms be defined in precisely the same way both when comparing data from different characterization techniques and even when correlating data from the same technique.  
3.2 It is likewise important that users of particle characterization methods and the data generated therefrom understand the principles of the methods, so that differences and similarities in the data can be interpreted in relation to those principles. That understanding can help to avoid disagreements when data from different characterization methods are compared.  
3.3 The definitions contained in this terminology will aid in the interpretation of particle characterization data with respect to the method(s) used to produce that data.
SCOPE
1.1 This terminology covers the definitions of terms used in the description and procedures of analysis of particulate materials not ordinarily analyzed using test sieves. The terms relate directly to the equipment used in analysis, the physical forms of the materials to be analyzed, and selected descriptive data reduction and analysis formats.  
1.2 Committee E29 on Particle and Spray Characterization believes that it is essential to include terms and definitions explicit to the committee’s scope, regardless of whether the terms appear in existing ASTM standards. Terms that are in common usage and appear in common-language dictionaries are generally not included, unless they have specific meanings in the context of particle characterization different from the common-language definitions.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D502-89(2023)(Test Method)
Standard Test Method for Particle Size of Soaps and Other Detergents

SIGNIFICANCE AND USE
3.1 This test method assures that the particle size of soaps and detergents conforms to specifications having to do with density and packaging, among others. It also offers a means of controlling the amount of potentially hazardous very low particle size material.
SCOPE
1.1 This test method covers the determination of the particle size of soaps and other detergents by hand sieving and machine sieving methods.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5444-23(Test Method)
Standard Test Method for Mechanical Size Analysis of Extracted Aggregate

SIGNIFICANCE AND USE
3.1 This test method is used to determine the grading of aggregates extracted from asphalt mixtures. The results are used to determine compliance of the particle size distribution with applicable specifications requirements, and to provide necessary data for control of the production of various aggregates to be used in asphalt mixtures.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers a procedure for determination of the particle size distribution of fine and coarse aggregates extracted from asphalt mixtures using sieves with square openings.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5158-23(Test Method)
Standard Test Method for Determination of Particle Size of Fine Mesh and Powdered Activated Carbon by Air-Jet Sieving

SIGNIFICANCE AND USE
5.1 The particle size of fine mesh and powdered activated carbon is sometimes used to evaluate filter cake filtration rates and the filter penetration in filtering applications.  
5.2 The selection and handling of fine mesh or powdered activated carbon, and operation of processes using fine mesh or powdered activated carbon, requires the knowledge of the particle size.  
5.3 This test method is intended for single sieve testing only. For determination of particle size distribution of a sample, the test must be repeated using sieves with different openings.
Note 1: Relative humidity (RH) can affect the repeatability and accuracy of this test. Activated carbon not at equilibrium with the RH of the ambient air may lose or gain weight accordingly, dependent upon whether the carbon picks up or loses moisture.
SCOPE
1.1 This test method covers the determination of the particle size of powdered activated carbons using an air-jet sieve device. For purposes of this test method, powdered activated carbon is defined as activated carbon in particle sizes predominantly in a range of 80 mesh (0.180 mm) through 500 mesh (0.025 mm).  
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM B821-23(Guide)
Standard Guide for Liquid Dispersion of Metal Powders and Related Compounds for Particle Size Analysis

SIGNIFICANCE AND USE
4.1 The method of powder dispersion in a liquid has a significant effect on the results of a particle size distribution analysis. The analysis will show a too-coarse, unstable, or nonrepeatable distribution if the powder has not been dispersed adequately. It is therefore important that parties wishing to compare their analyses use the same dispersion technique.  
4.2 This guide provides ways of deriving dispersion techniques for a range of metal powders and compounds. It should be used by all parties performing liquid-dispersed particle size analysis of all of the materials covered by this guide (see 1.1, 1.2, and 4.1).  
4.3 Table 1 provides some dispersion procedures that have been found useful and consistent for the particular materials listed there. These are only suggested dispersion procedures; the procedures and dispersion checks of 7.1.2 – 7.1.4, or the more detailed method development procedures of Guide E3340, should still be used to verify adequate dispersion for each particular material and particle size range. (A) Stated ultrasonic power and duration times are given as an indication only. Specific conditions should be sought for the particular system in question during the method development phase.(B) Tween 21, chemically known as polyoxyethylene6 sorbitan monolaurate, is manufactured by Croda International PLC, and is available from various chemical suppliers.(C) Three to five drops Tween 21 in 30 to 50 mL water.  
4.4 This guide should be used in the preparation of powders for use in Test Methods B761 and B822 and other procedures that analyze metal powder particle size distributions in liquid-dispersed systems.
SCOPE
1.1 This guide covers the dispersion in liquids of metal powders and related compounds for subsequent use in particle size analysis instruments. This guide describes a general procedure for achieving and determining dispersion; it also lists procedures that have been found useful for certain materials.  
1.2 This guide does not include specific procedures for dry dispersion of particulate materials. It only indicates when liquid dispersion is not appropriate and dry dispersion must be utilized (see 7.1.2.1). For guidance on development of methods of dry dispersion, see Guide E3340.  
1.3 This guide is limited to metal powders and related metal compounds. However, the general procedure described herein may be used, with caution as to its significance, for other particulate materials, such as ceramics, pigments, minerals, etc.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1638-22(Terminology)
Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media

SCOPE
1.1 This terminology includes all those terms used in all of the standards under the jurisdiction of Subcommittee E29.01. Terms are defined that are related to the manufacture of standard test sieves and screening media, as well as terms related to the methods, analysis, procedures, and equipment for sizing and separating particles.  
1.2 Committee E29 on Particle and Spray Characterization feels that it is essential to include terms and definitions explicit to the scope, regardless of whether the terms appear in existing ASTM standards. Terms that are in common usage and appear in common-language dictionaries are generally not included.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off