ASTM F1866-18

Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

ABSTRACT
This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40 drainage and DWV fittings. These fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts. Resistance to bending test, leak test, and solvent weld bond area test shall be performed to meet the requirements prescribed. The spigot diameter, spigot length, wall thickness, socket diameter, and socket length shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40 drainage and DWV fittings to be used with piping manufactured in accordance with Specifications D2665 or F891. These fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts.  
1.2 The requirements of this specification are to provide fabricated PVC fittings suitable for drainage and venting of sanitary waste systems, storm water systems, and certain other liquid wastes. Fittings shall have solvent cement joints, gasket joints or a combination thereof.  
1.3 The text of this specification references notes, footnotes, and appendixes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.  
1.5 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Jan-2018
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1866 − 18 An American National Standard
Standard Specification for
Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage
1
and DWV Fabricated Fittings
This standard is issued under the fixed designation F1866; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and test methods
2.1 ASTM Standards:
for fabricated poly(vinyl chloride) (PVC) plastic schedule 40
D618 Practice for Conditioning Plastics for Testing
drainage and DWV fittings to be used with piping manufac-
D1600 Terminology for Abbreviated Terms Relating to Plas-
tured in accordance with Specifications D2665 or F891. These
tics
fabricated fittings are manufactured from pipe, or from a
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
combination of pipe and injection molded parts.
Compounds and Chlorinated Poly(Vinyl Chloride)
1.2 The requirements of this specification are to provide
(CPVC) Compounds
fabricated PVC fittings suitable for drainage and venting of
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic
sanitary waste systems, storm water systems, and certain other
Pipe, Schedules 40, 80, and 120
liquid wastes. Fittings shall have solvent cement joints, gasket
D2122 Test Method for Determining Dimensions of Ther-
joints or a combination thereof.
moplastic Pipe and Fittings
D2564 Specification for Solvent Cements for Poly(Vinyl
1.3 The text of this specification references notes, footnotes,
Chloride) (PVC) Plastic Piping Systems
and appendixes that provide explanatory material. These notes
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic
and footnotes (excluding those in tables and figures) shall not
Drain, Waste, and Vent Pipe and Fittings
be considered as requirements of the specification.
D2855 Practice for the Two-Step (Primer and Solvent Ce-
1.4 The values stated in inch-pound units are to be regarded
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
as the standard. The values given in parentheses are provided
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
for information only.
Piping Components with Tapered Sockets
1.5 The following safety hazards caveat pertains only to the
D3212 Specification for Joints for Drain and Sewer Plastic
test method portion, Section 10, of this specification. This
Pipes Using Flexible Elastomeric Seals
standard does not purport to address all of the safety concerns,
F412 Terminology Relating to Plastic Piping Systems
if any, associated with its use. It is the responsibility of the user
F477 Specification for Elastomeric Seals (Gaskets) for Join-
of this standard to establish appropriate safety, health, and
ing Plastic Pipe
environmental practices and determine the applicability of
F656 Specification for Primers for Use in Solvent Cement
regulatory limitations prior to use.
Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and
1.6 This international standard was developed in accor-
Fittings
dance with internationally recognized principles on standard-
F891 Specification for Coextruded Poly(Vinyl Chloride)
ization established in the Decision on Principles for the
(PVC) Plastic Pipe With a Cellular Core
Development of International Standards, Guides and Recom-
F913 Specification for Thermoplastic Elastomeric Seals
mendations issued by the World Trade Organization Technical
(Gaskets) for Joining Plastic Pipe
Barriers to Trade (TBT) Committee.
1
This standard is under the jurisdiction of Committee F17 on Plastic Piping
2
Systems and is the direct responsibility of Subcommittee F17.63 on DWV. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2018. Published March 2018. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1998. Last previous edition approved in 2017 as F1866–13(2017). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1866-18. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1866 − 18
3. Terminology fitting manufacturer’s recommendations. All surfaces of the
joint that contact the gasket shall be smooth and free of
3.1 Definitions—Definitions are in accordance with Termi-
imperfections, ridges, fractures or cracks that could affect the
nology F412, and abbreviations are in accordance with Termi-
seal.
nology D1600, u
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1866 − 13 (Reapproved 2017) F1866 − 18 An American National Standard
Standard Specification for
Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage
1
and DWV Fabricated Fittings
This standard is issued under the fixed designation F1866; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for fabricated poly(vinyl chloride) (PVC) plastic schedule 40
drainage and DWV fittings to be used with piping manufactured in accordance with Specifications D2665 or F891. These
fabricated fittings are manufactured from pipe, or from a combination of pipe and injection molded parts.
1.2 The requirements of this specification are to provide fabricated PVC fittings suitable for drainage and venting of sanitary
waste systems, storm water systems, and certain other liquid wastes. Fittings shall have solvent cement joints, gasket joints or a
combination thereof.
1.3 The text of this specification references notes, footnotes, and appendixes that provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for
information only.
1.5 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D2855 Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated
Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F656 Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
F891 Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
1
This standard is under the jurisdiction of Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Aug. 1, 2017Feb. 1, 2018. Published September 2017March 2018. Originally approved in 1998. Last previous edition approved in 20132017
as F1866F1866–13(2017).–13. DOI: 10.1520/F1866-13R17.10.1520/F1866-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1866 − 18
F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
3. Termi
...