ASTM D7849-18a
(Classification)Standard Classification for Nomenclature of Reference Materials of Committee D24
Standard Classification for Nomenclature of Reference Materials of Committee D24
SIGNIFICANCE AND USE
3.1 Standard reference materials are used for calibration and verification of many carbon black tests under the jurisdiction of D24. This practice defines a systematic means of naming these reference materials and does so in a manner to clearly differentiate between the various reference materials as well as their version.
SCOPE
1.1 This classification covers instructions for naming the reference materials used by Committee D24.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7849 − 18a
Standard Classification for
1
Nomenclature of Reference Materials of Committee D24
This standard is issued under the fixed designation D7849; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope reference materials and does so in a manner to clearly
differentiate between the various reference materials as well as
1.1 This classification covers instructions for naming the
their version.
reference materials used by Committee D24.
4. Basis of Classification
1.2 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
4.1 ASTM Committee D24 has established five different
responsibility of the user of this standard to establish appro-
types of reference materials which serve to improve test
priate safety, health, and environmental practices and deter-
precision of analytical tests on carbon black as well as
3
mine the applicability of regulatory limitations prior to use.
in-rubber evaluation of carbon black.
1.3 This international standard was developed in accor-
4.1.1 SRB (Standard Reference Blacks)—A set of seven
dance with internationally recognized principles on standard-
carbon blacks, six furnace blacks with defined target values for
ization established in the Decision on Principles for the
iodine adsorption number (Test Method D1510), STSA (Test
Development of International Standards, Guides and Recom-
Method D6556), NSA (Test Method D6556), OAN (Test
mendations issued by the World Trade Organization Technical
Method D2414), COAN (Test Method D3493) and Tint
Barriers to Trade (TBT) Committee.
Strength (Test Method D3265) and one thermal black with
defined values for STSA (Test Method D6556), NSA (Test
2. Referenced Documents
Method D6556) and OAN (Test Method D2414). The SRBs
can be used to verify analytical test equipment and test
2
2.1 ASTM Standards:
procedures. For OAN and COAN, their application is manda-
D1510 Test Method for Carbon Black—Iodine Adsorption
tory to normalize measured data.
Number
4.1.2 ITRB (Industry Tint Reference Black)—ITRB repre-
D1619 Test Methods for Carbon Black—Sulfur Content
sents a standard carbon black of the N330 type. It is used for
D2414 Test Method for Carbon Black—Oil Absorption
verification and standardization in the test method for Tint
Number (OAN)
Strength (Test Method D3265).
D3265 Test Method for Carbon Black—Tint Strength
4.1.3 INR (Iodine Number Reference, previously designated
D3493 Test Method for Carbon Black—Oil Absorption
“HT”)—INR consist of three different reference blacks which
Number of Compressed Sample (COAN)
have been heat-treated in order to provide particularly high
D6556 Test Method for Carbon Black—Total and External
stability of the iodine number over a long period of time, that
Surface Area by Nitrogen Adsorption
is, over many years.
4.1.4 IRB (Industry Reference Black)—IRB is a carbon
3. Significance and Use
black of the N330 type which is produced in large quantities in
3.1 Standard reference materials are used for calibration and
order to serve as a reference material in rubber compounds.
verification of many carbon black tests under the jurisdiction of
In-rubber properties of this reference black are determined
D24. This practice defines a systematic means of naming these
during a round robin tests when the material is introduced.
4.1.5 STRM (Sulfur Test Reference Materials)—A set of five
carbon blacks with defined target values for sulfur in carbon
black testing (Test Methods D1619).
1
This classification is under the jurisdiction of ASTM Committee D24 on
Carbon Black and is the direct responsibility of Subcommittee D24.41 on Carbon
4.2 Nomenclature:
Black Nomenclature and Terminology.
4.2.1 All letters in the designation are in caps.
Current edition approved Nov. 1, 2018. Published November 2018. Originally
4.2.2 The reference material is identified by its type: SRB,
approved in 2014. Last previous edition approved in 2018 as D7849 – 18. DOI:
10.1520/D7849-18A.
ITRB, INR or IRB.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Target values and control limits are published on the website of the distributor
the ASTM website. of these reference materials, Balentine Enterprise Inc.: http://carbonstandard.com/.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ---------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7849 − 18 D7849 − 18a
Standard Classification for
1
Nomenclature of Reference Materials of Committee D24
This standard is issued under the fixed designation D7849; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This classification covers instructions for naming the reference materials used by Committee D24.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1510 Test Method for Carbon Black—Iodine Adsorption Number
D1619 Test Methods for Carbon Black—Sulfur Content
D2414 Test Method for Carbon Black—Oil Absorption Number (OAN)
D3265 Test Method for Carbon Black—Tint Strength
D3493 Test Method for Carbon Black—Oil Absorption Number of Compressed Sample (COAN)
D6556 Test Method for Carbon Black—Total and External Surface Area by Nitrogen Adsorption
3. Significance and Use
3.1 Standard reference materials are used for calibration and verification of many carbon black tests under the jurisdiction of
D24. This practice defines a systematic means of naming these reference materials and does so in a manner to clearly differentiate
between the various reference materials as well as their version.
4. Basis of Classification
4.1 ASTM Committee D24 has established fourfive different types of reference materials which serve to improve test precision
3
of analytical tests on carbon black as well as in-rubber evaluation of carbon black.
4.1.1 SRB (Standard Reference Blacks)—A set of seven carbon blacks, six furnace blacks with defined target values for iodine
adsorption number (Test Method D1510), STSA (Test Method D6556), NSA (Test Method D6556), OAN (Test Method D2414),
COAN (Test Method D3493) and Tint Strength (Test Method D3265) and one thermal black with defined values for STSA (Test
Method D6556), NSA (Test Method D6556) and OAN (Test Method D2414). The SRBs can be used to verify analytical test
equipment and test procedures. For OAN and COAN, their application is mandatory to normalize measured data.
4.1.2 ITRB (Industry Tint Reference Black)—ITRB represents a standard carbon black of the N330 type. It is used for
verification and standardization in the test method for Tint Strength (Test Method D3265).
4.1.3 INR (Iodine Number Reference, previously designated “HT”)—INR consist of three different reference blacks which have
been heat-treated in order to provide particularly high stability of the iodine number over a long period of time, that is, over many
years.
1
This classification is under the jurisdiction of ASTM Committee D24 on Carbon Black and is the direct responsibility of Subcommittee D24.41 on Carbon Black
Nomenclature and Terminology.
Current edition approved June 1, 2018Nov. 1, 2018. Published June 2018November 2018. Originally approved in 2014. Last previous edition approved in 20142018 as
D7849 – 14.D7849 – 18. DOI: 10.1520/D7849-18.10.1520/D7849-18A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Target values and control limits are published on the website of the distributor of these reference materials, Balentine Enterprise Inc.: http://carbonstandard.com/.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7849 − 18a
4.1.4 IRB (Industry Reference Black)—IRB is a carbon black of the N330 type which is produced in large quantities in order
to serve as a reference material in rubber compounds. In-rubber properties of this reference black are determined during a round
r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.