ASTM D6841-02
(Practice)Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-Retardant-Treated Lumber
Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-Retardant-Treated Lumber
SCOPE
1.1 This practice covers procedures for calculating treatment adjustment factors to be applied to design values for fire-retardant-treated lumber used at ambient temperatures [service temperatures up to 100—F (38—C)] and as framing in roof systems.
1.2 These design value treatment adjustment factors for the properties of extreme fiber in bending, tension parallel to grain, compression parallel to grain, horizontal shear and modulus of elasticity are based on the results of strength tests of matched treated and untreated small clear wood specimens after conditioning at nominal room temperatures [72°F (22°C)] and of other similar specimens after exposure at 150°F (66°C). The test data are developed in accordance with Test Method D 5664. Guidelines are provided for establishing adjustment factors for the property of compression perpendicular to grain and for connection design values.
1.3 Treatment adjustment factors for roof framing applications are based on computer generated thermal load profiles for normal wood roof construction used in a variety of climates as defined by weather tapes of the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE). The solar loads, moisture conditions, ventilation rates and other parameters used in the computer model were selected to represent typical sloped roof designs. The thermal loads in this practice are applicable to roof slopes of 3 in 12 or steeper, to roofs designed with vent areas and vent locations conforming to national standards of practice and to designs in which the bottom side of the roof sheathing is exposed to ventilation air. For designs that do not have one or more of these base-line features, the applicability of this practice needs to be documented by the user.
1.4 The procedures of this practice parallel those given in Practice D 6305. General references and commentary in Practice D 6305 are also applicable to this practice.
1.5 This practice is written in inch-pound units with SI units provided in parentheses for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 6841 – 02
Standard Practice for
Calculating Design Value Treatment Adjustment Factors for
1
Fire-Retardant-Treated Lumber
This standard is issued under the fixed designation D 6841; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This practice covers procedures for calculating treat-
responsibility of the user of this standard to establish appro-
ment adjustment factors to be applied to design values for
priate safety and health practices and determine the applica-
fire-retardant-treated lumber used at ambient temperatures
bility of regulatory limitations prior to use.
[service temperatures up to 100°F (38°C)] and as framing in
roof systems.
2. Referenced Documents
1.2 These design value treatment adjustment factors for the
2.1 ASTM Standards:
properties of extreme fiber in bending, tension parallel to grain,
3
D 9 Terminology Relating to Wood
compression parallel to grain, horizontal shear and modulus of
D 5664 Test Method for Evaluating the Effects of Fire-
elasticity are based on the results of strength tests of matched
Retardant Treatments and Elevated Temperatures on
treated and untreated small clear wood specimens after condi-
3
Strength Properties of Fire-Retardant-Treated Lumber
tioning at nominal room temperatures [72°F (22°C)] and of
D 6305 Practice for Calculating Bending Strength Design
other similar specimens after exposure at 150°F (66°C). The
Adjustment Factors for Fire-Retardant-Treated Plywood
test data are developed in accordance with Test Method
3
Roof Sheathing
D 5664. Guidelines are provided for establishing adjustment
factors for the property of compression perpendicular to grain
3. Terminology
and for connection design values.
3.1 Definitions:
1.3 Treatment adjustment factors for roof framing applica-
3.1.1 Definitions used in this practice are in accordance with
tions are based on computer generated thermal load profiles for
Terminology D 9.
normal wood roof construction used in a variety of climates as
3.2 Definitions of Terms Specific to This Standard:
defined by weather tapes of the American Society of Heating,
3.2.1 bin mean temperature—10°F (5.5°C) temperature
Refrigerating and Air-Conditioning Engineers, Inc.
2 ranges having mean temperatures of 105 (41), 115 (46), 125
(ASHRAE). The solar loads, moisture conditions, ventilation
(52), 135 (57), 145 (63), 155 (68), 165 (74), 175 (79) and
rates and other parameters used in the computer model were
185°F (85°C).
selected to represent typical sloped roof designs. The thermal
3.2.2 thermal load profile—the cumulative time per year in
loads in this practice are applicable to roof slopes of 3 in 12 or
each 10°F (5.5°C) temperature bin.
steeper, to roofs designed with vent areas and vent locations
conforming to national standards of practice and to designs in
4. Summary of Practice
which the bottom side of the roof sheathing is exposed to
4.1 Test results developed in accordance with Test Method
ventilation air. For designs that do not have one or more of
D 5664 are used in conjunction with computer generated
these base-line features, the applicability of this practice needs
thermal load profiles to calculate treatment factors that are
to be documented by the user.
applied to published design values for untreated lumber. These
1.4 The procedures of this practice parallel those given in
treatment adjustment factors account for the combined effect of
Practice D 6305. General references and commentary in Prac-
fire-retardant-treatment and service temperatures.
tice D 6305 are also applicable to this practice.
1.5 This practice is written in inch-pound units with SI units
5. Significance and Use
provided in parentheses for information only.
5.1 Fire-retardant-treatments are used to reduce the flame-
spread characteristics of wood. Chemicals and redrying condi-
tions employed in treatments are known to modify the strength
1
This practice is under the jurisdiction of ASTM Committee D07 on Wood and
properties of the wood product being treated. This practice
is the direct responsibility of Subcommittee D07.07 on Fire Performance of Wood.
Current edition approved Nov. 10, 2002. Published January 2003.
2
American Society of Heating, Refrigerating, and Air-Conditioning Engineers,
3
Inc. (ASHRAE), 1791 Tullie Circle, NE, Atlanta, GA 30329. Annual Book of ASTM Standards, Vol 04.10.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
----
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.