ASTM C216-03a

Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

SCOPE
1.1 This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure.
1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 6) of this standard is beyond the scope of this standard.
1.3 The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C 902).
1.4 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see firing, fired bond, and incipient fusion in Terminology C 43).
1.5 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick.
1.6 Three types of brick in each of two grades are covered.
1.7 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

• Status: Historical
• Publication Date: 09-Jun-2003
• ICS: 91.100.15 - Mineral materials and products
• Technical Committee: C15 - Manufactured Masonry Units
• Drafting Committee: C15.02 - Brick and Structural Clay Tile

Relations

• Replaces: ASTM C216-03 - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
• Effective Date: 10-Jun-2003
• Replaced By: ASTM C216-04 - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
• Effective Date: 01-Feb-2004
• Referred By: ASTM C652-22 - Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)
• Effective Date: 10-Jun-2003
• Referred By: ASTM C1283-15(2021) - Standard Practice for Installing Clay Flue Lining
• Effective Date: 10-Jun-2003
• Referred By: ASTM C1232-21a - Standard Terminology for Masonry
• Effective Date: 10-Jun-2003
• Referred By: ASTM E2266-22 - Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
• Effective Date: 10-Jun-2003
• Referred By: ASTM C62-23 - Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
• Effective Date: 10-Jun-2003
• Referred By: ASTM C1713-23 - Standard Specification for Mortars for the Repair of Historic Masonry
• Effective Date: 10-Jun-2003
• Referred By: ASTM C34-23 - Standard Specification for Structural Clay Loadbearing Wall Tile
• Effective Date: 10-Jun-2003
• Referred By: ASTM C1472-16(2022) - Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
• Effective Date: 10-Jun-2003

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 216 – 03a
Standard Specification for
Facing Brick (Solid Masonry Units Made from Clay or
1
Shale)
This standard is issued under the fixed designation C 216; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C 67 Test Methods of Sampling and Testing Brick and
2
Structural Clay Tile
1.1 This specification covers brick intended for use in
C 902 Specification for Pedestrian and Light Traffic Paving
masonry and supplying structural or facing components, or
2
Brick
both, to the structure.
E 835/E 835M Guide for Modular Coordination of Clay
1.2 The property requirements of this standard apply at the
3
and Concrete Masonry Units
time of purchase. The use of results from testing of brick
extracted from masonry structures for determining conform-
3. Grades
ance or nonconformance to the property requirements (Section
3.1 Grades classify brick according to their resistance to
6) of this standard is beyond the scope of this standard.
damage by freezing when saturated at a moisture content not
1.3 The brick are prismatic units available in a variety of
exceeding the 24-h cold water absorption. Two grades of facing
sizes, textures, colors, and shapes. This specification is not
brick are covered and the requirements are given in Section 6.
intended to provide specifications for paving brick (see Speci-
3.1.1 Grade SW (Severe Weathering)—Brick intended for
fication C 902).
use where high resistance to damage caused by cyclic freezing
1.4 Brick are manufactured from clay, shale, or similar
is desired.
naturally occurring earthy substances and subjected to a heat
3.1.2 Grade MW (Moderate Weathering)—Brick intended
treatment at elevated temperatures (firing). The heat treatment
for use where moderate resistance to cyclic freezing damage is
must develop a fired bond between the particulate constituents
permissible.
to provide the strength and durability requirements of this
specification (see firing, fired bond, and incipient fusion in
NOTE 1—Measurement of moisture content of brick in buildings
Terminology C 43). indicates that, when the building is designed and constructed to reduce
water penetration, the 24-h cold water absorption is unlikely to be
1.5 Brick are shaped during manufacture by molding, press-
exceeded.
ing, or extrusion, and the shaping method is a way to describe
the brick.
4. Types
1.6 Three types of brick in each of two grades are covered.
4.1 Three types of facing brick are covered:
1.7 The text of this standard references notes and footnotes
4.1.1 Type FBS—Brick for general use in masonry.
which provide explanatory material. These notes and footnotes
4.1.2 Type FBX—Brick for general use in masonry where a
(excluding those in tables and figures) shall not be considered
higher degree of precision and lower permissible variation in
as requirements of the standard.
size than permitted for Type FBS is required.
1.8 The values stated in inch-pound units are to be regarded
4.1.3 Type FBA—Brick for general use in masonry selected
as the standard. The values given in parentheses are for
to produce characteristic architectural effects resulting from
information only.
nonuniformity in size and texture of the individual units.
4.2 When the type is not specified, the requirements for
2. Referenced Documents
Type FBS shall govern.
2.1 ASTM Standards:
2
C 43 Terminology of Structural Clay Products
5. Ordering Information
5.1 Orders for facing brick under this specification shall
include the following information:
1
This specification is under the jurisdiction of ASTM Committee C15 on
5.1.1 Grade (Section 3)—Grade SW governs when Grade is
Manufactured Masonry Units and is the direct responsibility of Subcommittee
not specified.
C15.02 on Brick and Structural Clay Tile.
Current edition approved June 10, 2003. Published August 2003. Originally
approved in 1947. Last previous edition approved in 2003 as C 216–03.
2 3
Annual Book of ASTM Standards, Vol 04.05. Annual Book of ASTM Standards, Vol 04.11.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C 216 – 03a
TABLE 1 Physical Requirements
Minimum Compressive Strength Maximum Water Absorption Maximum Saturation
A
psi,
...