iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1045-06

(Specification)

Standard Performance Specification for Ice Hockey Helmets

Standard Performance Specification for Ice Hockey Helmets

SCOPE
1.1 This performance specification covers performance requirements for ice hockey helmets.
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.
1.4 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Jan-2006
ICS
13.340.20 - Head protective equipment
97.220.30 - Indoor sports equipment
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.15 - Ice Hockey
Current Stage
Ref Project

Relations

Replaces
ASTM F1045-04 - Standard Performance Specification for Ice Hockey Helmets
Effective Date
15-Jan-2006
Replaced By
ASTM F1045-07 - Standard Performance Specification for Ice Hockey Helmets
Effective Date
15-Jul-2007
Referred By
ASTM F1937-04(2023) - Standard Specification for Body Protectors Used in Horse Sports and Horseback Riding
Effective Date
15-Jan-2006

Buy Standard

ASTM F1045-06 - Standard Performance Specification for Ice Hockey HelmetsASTM F1045-06 - Standard Performance Specification for Ice Hockey Helmets
PreviousNext
Technical specification
ASTM F1045-06 - Standard Performance Specification for Ice Hockey Helmets
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1045 – 06
Standard Performance Specification for
1
Ice Hockey Helmets
This standard is issued under the fixed designation F 1045; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Ice hockey is a contact sport with intrinsic hazards. The use of protective equipment will not
eliminateallinjuriesbutshouldsubstantiallyreducetheseverityandfrequencyofinjury.Participation
in the sport of ice hockey by a player implies acceptance of some risk of injury. The goal is to
minimize this risk.
This performance specification for head protective equipment has been prepared after consideration
of head protection relative to the following principle risks: high-mass, low-velocity impact (various
playing situations), and fit. This performance specification may be modified as other risks are
identified.
Performance requirements were determined after consideration of state-of-the-art of helmet design
and manufacture and the demands of the sport.
1. Scope 2. Referenced Documents
2 3
1.1 This performance specification covers performance 2.1 ASTM Standards:
requirements for ice hockey helmets. F 513 Safety Specification for Eye and Face Protective
1.2 The intent of this performance specification is to reduce Equipment for Hockey Players
the risk of injury to the head without compromising the form F 2220 Specification for Headforms
and appeal of the game.
3. Terminology
1.3 This performance specification covers: (1) performance
3.1 Definitions of Terms Specific to This Standard:
tests for shock absorption properties of the complete helmet
and strength and elongation of the chin strap and its attach- 3.1.1 retention system:
3.1.1.1 chin strap—the chin strap, including a cup that
ment; and (2) requirements for area of coverage and penetra-
tion. covers the chin (see Fig. 1), is affixed to both sides of the
helmet and secures the helmet to the head when a Type II full
1.4 The values as stated in inch-pound units are to be
regarded as the standard. The values in parentheses are given face protector is not worn with the helmet.
3.1.1.2 neck strap—theneckstrapthatsecuresthehelmetto
for information only.
1.5 The following precautionary caveat pertains only to the theheadisaffixedonbothsidesofthehelmetandpassesunder
the lower jaw in close proximity to the jaw and the neck.
test methods portion, Section 12, of this performance specifi-
cation: This standard does not purport to address all of the Where the helmet is worn with aType II full face protector, the
neck strap serves as the attachment of the helmet to the head.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
NOTE 1—For a description of the Type II face protector, see the Types
priate safety and health practices and determine the applica-
of Protectors Section in Safety Specification F 513.
bility of regulatory limitations prior to use.
3.1.2 crown—apointinthemedianplanethatisequalchord
lengths from the anterior and posterior intersections of the
1 median and reference planes.
This performance specification is under the jurisdiction of ASTM Committee
F08 on Sports Equipment and Facilities and is the direct responsibility of
Subcommittee F08.15 on Ice Hockey.
3
Current edition approved Jan. 15, 2006. Published January 2006. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1988. Last previous edition approved in 2004 as F 1045 – 04. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
Thisperformancespecificationissubjecttorevisionasindicatedbysubsequent Standards volume information, refer to the standard’s Document Summary page on
injury statistics and subject to review at least every five years. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1045–06
FIG. 1 Chin Strap (Includes a Chin Cup)
3.1.3 drop height—the vertical distance between the lowest
point (impact point) of the elevated helmet and the apex of the
impact surface.
3.1.4 g—the dimensionless ratio of the acceleration of the
headform during impact to the acceleration due to gravity.
3.1.4.1 g —the maximum value of g encountered during
max
impact.
3.1.5 helmet—the complete product, including the shell,
liner,chinstrap,includingthecuporneckstrap,andassociated
attachment hardware, assembled with components supplied by
the manufacturer. The helmet is intended to protect the
wearer’s head while
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1045-22(Specification)
Standard Performance Specification for Ice Hockey Helmets

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM F513-22(Specification)
Standard Specification for Eye and Face Protective Equipment for Hockey Players

SCOPE
1.1 This specification covers performance requirements and test methods for face protectors marketed, sold, and intended for ice hockey.  
1.2 The intent of this specification is to reduce the risk of injury to the face without compromising the form or appeal of the game. To do so, the face protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a face protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with facial and eye injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Penetration,  
1.5.4 Field of vision, and  
1.5.5 Marking and information.  
1.6 Face protection is intended for use by players, goalkeepers, and certain functionaries (for example, referees and coaches). Types of protectors considered under this specification are:  
1.6.1 Type B1—A full-face protector intended for use by persons older than ten years of age, other than goaltenders;  
1.6.2 Type B2—A full-face protector intended for use by persons ten years of age or younger, other than goaltenders; and  
1.6.3 Type C (Visor)—A visor intended for use by person in the junior age category and older, other than goaltenders.  
1.7 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.8 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.9 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM F1045-22(Specification)
Standard Performance Specification for Ice Hockey Helmets

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM F513-22(Specification)
Standard Specification for Eye and Face Protective Equipment for Hockey Players

SCOPE
1.1 This specification covers performance requirements and test methods for face protectors marketed, sold, and intended for ice hockey.  
1.2 The intent of this specification is to reduce the risk of injury to the face without compromising the form or appeal of the game. To do so, the face protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a face protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with facial and eye injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Penetration,  
1.5.4 Field of vision, and  
1.5.5 Marking and information.  
1.6 Face protection is intended for use by players, goalkeepers, and certain functionaries (for example, referees and coaches). Types of protectors considered under this specification are:  
1.6.1 Type B1—A full-face protector intended for use by persons older than ten years of age, other than goaltenders;  
1.6.2 Type B2—A full-face protector intended for use by persons ten years of age or younger, other than goaltenders; and  
1.6.3 Type C (Visor)—A visor intended for use by person in the junior age category and older, other than goaltenders.  
1.7 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.8 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.9 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off