ASTM B127-05

Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip

ABSTRACT
This specification covers rolled nickel-copper alloy (UNS N04400) plate, sheet, and strip. The matreial shall conform to the required chemical composition for nickel, copper, iron, manganese, carbon, silicon, and sulfur. The material shall conform to the required mechanical propeties such as tensile strength, yield strength, elongation, and Rockwell hardness. The material shall conform to the required grain size. Dimensions such as plate, sheet, and strip thickness, width, or diameter, length, straightness, edges, squareness, and flatness shall be determined.
SCOPE
1.1 This specification covers rolled nickel-copper alloy (UNS N04400)* plate, sheet, and strip.
1.2 The values stated in inch-pound units are to be regarded as the standard. The other values given are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Apr-2005
• ICS: 77.150.40 - Nickel and chromium products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B127-98 - Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
• Effective Date: 01-May-2005
• Replaced By: ASTM B127-05(2009) - Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
• Effective Date: 01-Oct-2009
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-May-2005
• Referred By: ASTM F859-21 - Standard Specification for Heat-Sanitizing Commercial Dishwashing Machines, Multiple Tank, Conveyor Rack Type
• Effective Date: 01-May-2005
• Referred By: ASTM A265-12(2019) - Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate
• Effective Date: 01-May-2005
• Referred By: ASTM F953-19 - Standard Specification for Commercial Dishwashing Machines (Stationary Rack, Dump Type) Chemical Sanitizing
• Effective Date: 01-May-2005
• Referred By: ASTM B164-03(2019) - Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
• Effective Date: 01-May-2005
• Referred By: ASTM B474/B474M-19 - Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe
• Effective Date: 01-May-2005
• Referred By: ASTM F2643-20 - Standard Specification for Powered Pot, Pan and Utensil Washing Sinks
• Effective Date: 01-May-2005
• Referred By: ASTM F860-07(2018)e1 - Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type
• Effective Date: 01-May-2005
• Referred By: ASTM F85-76(2018) - Standard Practice for Nomenclature for Wire Leads Used as Conductors in Electron Tubes (Withdrawn 2023)
• Effective Date: 01-May-2005
• Referred By: ASTM F1202-22 - Standard Specification for Washing Machines, Heat Sanitizing, Commercial, Pot, Pan, and Utensil Vertically Oscillating Arm Type
• Effective Date: 01-May-2005
• Referred By: ASTM F857-17 - Standard Specification for Hot Water and Chemical Sanitizing Commercial Dishwashing Machines, Stationary Rack Type
• Effective Date: 01-May-2005
• Referred By: ASTM F1203-22 - Standard Specification for Washing Machines—Pot, Pan, and Utensil, Heat Sanitizing, Commercial Rotary Conveyor Type
• Effective Date: 01-May-2005
• Referred By: ASTM F858-18 - Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Single Tank, Conveyor Rack Type
• Effective Date: 01-May-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 127 – 05 Used in USDOE-NE standards
Standard Specification for
1
Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
This standard is issued under the fixed designation B 127; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
5
1. Scope* 2.3 Military Standards:
2 MIL-STD-129 Marking for Shipment and Storage
1.1 This specification covers rolled nickel-copper alloy
MIL-STD-271 Nondestructive Testing Requirements for
(UNS N04400)* plate, sheet, and strip.
Metals
1.2 The values stated in inch-pound units are to be regarded
as the standard. The other values given are for information
3. Terminology
only.
3.1 Descriptions of Terms Specific to This Standard—The
1.3 This standard does not purport to address all of the
terms given in Table 1 shall apply.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate
TABLE 1 Product Description
Material Safety Data Sheet for this product/material as pro-
Product Thickness, in. (mm)
vided by the manufacturer, to establish appropriate safety and
A
3
Hot-rolled plate ⁄16 and over
A
health practices, and determine the applicability of regulatory
Hot-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl
B
Cold-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl
limitations prior to use.
B
Cold-rolled strip 0.005 to 0.250 (0.13 to 6.4), incl
A
3 1
2. Referenced Documents Material ⁄16 to ⁄4 in. (4.8 to 6.4 mm), incl, in thickness may be furnished as
sheet or plate provided the material meets the specification requirements for the
3
2.1 ASTM Standards:
condition ordered.
B
B 906 Specification for General Requirements for Flat- Material under 48 in. (1219 mm) in width may be furnished as sheet or strip
provided the material meets the specification requirements for the condition
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
ordered.
E 140 Hardness Conversion Tables for Metals
F 155 TestMethodforTemperofStripandSheetMetalsfor
4
Electronic Devices (Spring-Back Method)
4. General Requirements
5
2.2 Federal Standards:
4.1 Material furnished under this specification shall con-
Fed. Std. No. 102 Preservation, Packaging, and Packing
form to the applicable requirements of Specification B 906
Levels
unless otherwise provided herein.
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
Fed. Std. No. 182 Continuous Identification Marking of 5. Ordering Information
Nickel and Nickel-Base Alloys
5.1 It is the responsibility of the purchaser to specify all
requirements that are necessary for material ordered under this
1 specification. Examples of such requirements include, but are
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee not limited to the following:
B02.07 on Refined Nickel and Cobalt and Their Alloys.
5.1.1 Alloy—Name or UNS number (see Table 2).
Current edition approved May 1, 2005. Published June 2005. Originally
5.1.2 ASTM designation, including year of issue.
approved in 1939. Last previous edition approved in 1998 as B 127 - 98.
2
5.1.3 Condition—See 7.1, 7.2, and Appendix X1.
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
cation SB-127 in Section II of that code.
5.1.4 Finish—See Appendix X1.
* New designation established in accordance withASTM E 527 and SAE J1086,
5.1.5 Dimensions—Thickness, width, and length.
Practice for Numbering Metals and Alloys (UNS).
3 5.1.6 Quantity.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.7 Optional Requirements:
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
5.1.7.1 Sheet and Strip—Whether to be furnished in coil, in
the ASTM website.
cut straight lengths, or in random straight lengths.
4
Withdrawn.
5 5.1.7.2 Strip—Whethertobefurnishedwithcommercialslit
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098 edge, square edge, or round edge.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B127–05
TABLE 2 Chemical Requirements
6. Chemical Composition
Composition,%
6.1 The material shall conform to the re
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B127–98 Designation: B 127 – 05 Used in USDOE-NE standards
Standard Specification for
1
Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
This standard is issued under the fixed designation B 127; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers rolled nickel-copper alloy (UNS N04400)* plate, sheet, and strip.
1.2 The values stated in inch-pound units are to be regarded as the standard. The other values given are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheetforthisproduct/materialasprovidedbythemanufacturer,toestablishappropriatesafetyandhealthpractices,anddetermine
the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B164Specification for Nickel-Copper Alloy Rod, Bar, and Wire 906 Specification for General Requirements for Flat-Rolled
Nickel and Nickel Alloys Plate, Sheet, and Strip
E8Test Methods for Tension Testing of Metallic Materials
4
E10Test Method for Brinell Hardness of Metallic Materials
4
E18Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials
E29Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E76Test Methods for Chemical Analysis of Nickel-Copper Alloys
4
E112Test Methods for Determining the Average Grain Size
4
E140Hardness Conversion Tables for Metals
140 Hardness Conversion Tables for Metals
4
F 155 Test Method for Temper of Strip and Sheet Metals for Electronic Devices (Spring-Back Method)
5
2.2 Military Standards: Federal Standards:
Fed. Std. No. 102 Preservation, Packaging, and Packing Levels
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
Fed. Std. No. 182 Continuous Identification Marking of Nickel and Nickel-Base Alloys
5
2.3 Military Standards:
MIL-STD-129 Marking for Shipment and Storage
MIL-STD-271 Nondestructive Testing Requirements for Metals
3. Terminology
3.1 Descriptions of Terms Specific to This Standard—The terms given in Table 1 shall apply.
4. Ordering Information
4.1Orders for material under this specification shall include the following information:
1
This specification is under the jurisdiction of ASTM Committee B-2B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on
Refined Nickel and Cobalt and Their Alloys.
Current edition approved Aug. 10, 1998.May 1, 2005. Published October 1998.June 2005. Originally published as B127–39T.approved in 1939. Last previous edition
{1
B127–93a . approved in 1998 as B 127 - 98.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-127 in Section II of that code.
* New designation established in accordance with ASTM E 527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Annual Book of ASTM Standards, Vol 03.01.
4
Withdrawn.
5
Annual Book of ASTM Standards, Vol 14.02.
5
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B127–05
TABLE 1 Product Description
Thickness, in. (mm)Width, in.
Product
(mm)
A 3 B
Hot-rolled plate ⁄16 and over (Table 5 and Table 6) (Table 8)
A
Hot-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (Table 7) (Table 10)
C
Cold-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (Table 7) (Table 10)
B
Cold-rolled sheet 0.018 to 0.250 (0.46 to 6.4), incl (Table 7) (Table 10)
C
Cold-rolled strip 0.005 to 0.250 (0.13 to 6.4), incl (Table 7) (Table 10)
B
Cold-rolled strip 0.005 to 0.250
...