ASTM D5652-95
(Test Method)Standard Test Methods for Bolted Connections in Wood and Wood-Base Products
Standard Test Methods for Bolted Connections in Wood and Wood-Base Products
SCOPE
1.1 These test methods cover procedures for evaluating the strength and stiffness of single-bolted connections in wood or wood-base products when subjected to static loading. These test methods serve as a basis for determining the effects of various factors on the strength and stiffness of the connection.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 5652 – 95
Standard Test Methods for
Bolted Connections in Wood and Wood-Base Products
This standard is issued under the fixed designation D 5652; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope cal properties of the wood or wood-base members are also
determined.
1.1 These test methods cover procedures for evaluating the
strength and stiffness of single-bolted connections in wood or
4. Significance and Use
wood-base products when subjected to static loading. These
4.1 Connections are one of the weakest links in wood
test methods serve as a basis for determining the effects of
construction. While the strength of metal bolts and of wood or
various factors on the strength and stiffness of the connection.
wood-base products are ascertainable, a full evaluation of the
1.2 The values stated in inch-pound units are to be regarded
performance of the combination is only possible through the
as the standard. The SI units in parentheses are for information
testing of a complete connection. Such variables as member
only.
thickness, member width, end and edge distances, type of bolt,
1.3 This standard does not purport to address all of the
fabrication tolerances, moisture content of the wood or wood-
safety concerns, if any, associated with its use. It is the
base product, preservative or fire-retardant treatment of the
responsibility of the user of this standard to establish appro-
wood or wood-base product, and species of wood may affect
priate safety and health practices and determine the applica-
connection behavior. In order to develop design criteria for
bility of regulatory limitations prior to use.
established bolt types as well as those under development, the
2. Referenced Documents effect of these variables on connection strength and stiffness
must be known. The tests described herein permit the obser-
2.1 ASTM Standards:
vation of data on the strength and stiffness of wood or
D 2395 Test Methods for Specific Gravity of Wood and
2 wood-base connections, or both, under the influence of any or
Wood-Base Materials
all of these factors.
D 2915 Method for Evaluating Allowable Properties for
Grades of Structural Lumber
5. Apparatus
D 4442 Test Methods for Direct Moisture Content Measure-
2 5.1 Testing Machine—Any suitable testing machine capable
ment of Wood and Wood-Base Materials
3 of operation at a constant rate of motion of its movable head
E 4 Practice for Force Verification of Testing Machines
and having an accuracy of 61 % when calibrated in accor-
F 606 Test Methods for Determining the Mechanical Prop-
dance with Practices E 4.
erties of Externally and Internally Threaded Fasteners,
4 5.2 Spherical Bearing Block, for compressive loading of
Washers, and Rivets
specimens.
2.2 Federal Specification:
5.3 Grips—Gripping devices capable of attaching the speci-
Fed. Spec. FF-W-92 for Washers, Metal, Flat (Plain)
men to the stationary and moving heads of the testing machine
3. Summary of Test Methods in such a way as to ensure true axial tensile loads.
5.4 Deformation Gages—At least two dial gages with a
3.1 Specimens consisting of at least one wood or wood-base
least reading of 0.001 in. (0.025 mm) or other suitable devices
member fastened with one bolt to at least one other member of
for measuring the slip between connection members during
any material are evaluated for capacity to resist compressive or
load application.
tensile forces applied at a constant rate of deformation with a
suitable testing machine. The deformation of the connection at
6. Sampling
various intervals of loading is measured. Supplementary physi-
6.1 Sampling shall provide for selection of representative
test specimens that are appropriate to the objectives of the
These test methods are under the jurisdiction of ASTM Committee D-7 on
testing program.
Wood and are the direct responsibility of Subcommittee D07.05 on Wood Assem-
6.2 Estimate sample size in accordance with the procedures
blies.
Current edition approved Jan 15, 1995. Published March 1995.
of Method D 2915.
Annual Book of ASTM Standards, Vol 04.10.
Annual Book of ASTM Standards, Vol 03.01. NOTE 1—The precision required, and thus, the manner of sampling and
Annual Book of ASTM Standards, Vol 15.08.
the number of tests, depend upon the specific test objectives. No specific
Available from Superintendent of Documents, U.S. Government Printing
criteria can therefore be established. General experience indicates that the
Office, Washington, DC 20402.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
D 5652
coefficients of variation from tests on connections range from approxi-
mately 15 to 30 %.
7. Sampling: Test Specimens and Test Units
7.1 Select wood members, and position the bolt in them in
such a way that the results are not affected by knots, cross
grain, or other natural or manufacturing characteristics unless
the purpose of the test methods is to evaluate the effects of such
growth characteristics. When the affects of growth character-
istics are not being evaluated, wood members shall be essen-
tially clear and straight-grained. For wood-base products,
select specimens with regard to manufactured characteristics.
FIG. 2 Assembly for Testing Bolted Connections Parallel to Grain
7.2 Connections Containing One Bolt:
in Compression
7.2.1 Make tests on three-member connections as shown in
Figs. 1-3 except where specific data on two- or multiple-
member connections are being sought. Select the width, length,
and thickness of the members with consideration of required
edge and end distances. Member dimensions shall be represen-
tative of the intended use of the connection.
FIG. 3 Assembly for Testing Bolted Connections Perpendicular to
Grain in Compression
7.2.2 For connections involving metal or other side mem-
bers (such as panel materials), the side member thickness shall
be that anticipated in service. For all-wood joints, the thickness
of each side member shall be at least one half of the thickness
of the center member and width and length of all members
shall be selected with consideration of required edge and end
distances for a specific application. Minimum end distance
shall be four bolt diameters for compression loading and seven
bolt diameters for tension loading, unless the effect of various
end distances is to be studied.
7.2.3 The excess of bolt-hole diameter over bolt diameter
1 1
shall be ⁄32 in. (0.8 mm) for bolts ⁄2 in. (13 mm) or less in
diameter, and ⁄16 in. (1.6 mm) for bolts of larger diameter,
unless other bolt-hole diameters are specified.
7.2.3.1 Bolt-holes shall be precisely bored perpendicular to
the surface, so that the surface of the hole is smooth and
uniform to ensure good bearing of the bolt. Holes shall be
drilled after members are conditioned unless the purpose of the
test is to study the effect of shrinkage on the performance of
bolted connections.
7.2.4 Bolts shall be of sufficient length to penetrate all
members without having any member bear on the bolt threads.
7.2.5 Place heavy round washers conforming to Fed. Spec.
FF-W-92 for washers, metal, flat (plain), and hereafter referred
to as a standard washer, between wood or wood-base side
members and bolt head and nut. Bring abutting faces of
connection members into normally installed contact; then back
off the nut and retighten to “finger tightness”.
7.2.6 Primary tests shall be made on connections loaded
parallel to the grain of wood members and perpendicular to the
grain of wood members. Perpendicular to the grain tests shall
be conducted with the grain of the center member parallel and
the side members perpendicular to the direction of the load or
with the grain of the center member perpendicular and the side
FIG. 1 Assembly for Testing Bolted Connections Parallel to Grain
in Tension members parallel to the direction of the load. These tests shall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.