iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2266-03(2015)

(Specification)

Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)

Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)

ABSTRACT
This specification defines the masses to be used when testing rescue systems and components. The masses represent personnel and equipment that may be attached to a rescue system or components. However, the masses do not represent any particular type or kind of rescuer or equipment. The masses shall be classified as follows: Type I; Type II; Type III; Type IV; and Type V.
SCOPE
1.1 This specification defines the masses to be used when testing rescue systems and components.  
1.2 The masses represent personnel and equipment that may be attached to a rescue system or components. However, the masses do not represent any particular type or kind of rescuer or equipment.  
1.2.1 The masses chosen have been used in the past or are in current use in testing of rescue systems and components. Limiting testing to the masses listed in this specification allows meaningful comparisons between past, current, and future test results.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 The user of this specification shall determine which mass(es) represent(s) the personnel and equipment attached to the system or component under test.  
1.5 For the purposes of this specification, mass and weight are synonymous when the object(s) representing the mass(es) are weighed in air anywhere on Earth.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
30-Nov-2015
Withdrawal Date
28-Jan-2024
ICS
11.160 - First aid
13.200 - Accident and disaster control
Technical Committee
F32 - Search and Rescue
Drafting Committee
F32.01 - Equipment, Testing, and Maintenance
Current Stage
Ref Project

Relations

Replaces
ASTM F2266-03(2008)e1 - Standard Specification for Masses Used in Testing Rescue Systems and Components
Effective Date
01-Dec-2015
Replaced By
ASTM F2266-24e1 - Standard Specification for Masses Used in Testing Rescue Systems and Components
Effective Date
01-Apr-2024
Referred By
ASTM F2822-10(2016) - Standard Specification for Fixed Anchorages Installed on Structures used for Rope Rescue Training
Effective Date
01-Dec-2015
Referred By
ASTM F2436-14(2019) - Standard Test Method for Measuring the Performance of Synthetic Rope Rescue Belay Systems Using a Drop Test
Effective Date
01-Dec-2015

Buy Standard

ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and ComponentsASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components
PreviousNext
Technical specification
ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)
PreviousNext
Technical specification
ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)REDLINE ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)
PreviousNext
Technical specification
REDLINE ASTM F2266-03(2015) - Standard Specification for Masses Used in Testing Rescue Systems and Components (Withdrawn 2024)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F2266 −03(Reapproved 2015)
Standard Specification for
Masses Used in Testing Rescue Systems and Components
This standard is issued under the fixed designation F2266; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 American National Standards Institute (ANSI) Stan-
dard:
1.1 This specification defines the masses to be used when
ANSI Z359.1 Safety Requirements for Personal Fall Arrest
testing rescue systems and components.
Systems, Sub-Systems and Components
1.2 The masses represent personnel and equipment that may
2.3 European Committee for Standardization (CEN) Stan-
be attached to a rescue system or components. However, the 4
dard:
masses do not represent any particular type or kind of rescuer
EN1891 Personal Protective Equipment for the Prevention
or equipment.
of Falls from a Height—Low Stretch Kernmantel Ropes
1.2.1 The masses chosen have been used in the past or are
in current use in testing of rescue systems and components.
3. Terminology
Limiting testing to the masses listed in this specification allows
3.1 Definitions of Terms Specific to This Standard:
meaningful comparisons between past, current, and future test
3.1.1 rescue system, n—an assembly of ropes, cables, lines,
results.
and other components that may be used to raise, lower,
1.3 The values stated in SI units are to be regarded as suspend, support, or traverse persons or equipment during a
standard. No other units of measurement are included in this rescue.
standard.
4. Classification
1.4 The user of this specification shall determine which
4.1 Type I—80 6 1 kg.
mass(es) represent(s) the personnel and equipment attached to
4.1.1 ThesourceofthismassistheUnionInternationaledes
the system or component under test.
Associations d’Alpinisme (UIAA) and is the mass used in its
1.5 For the purposes of this specification, mass and weight
mountaineering equipment standards.
are synonymous when the object(s) representing the mass(es)
4.2 Type II—100 6 1 kg.
are weighed in air anywhere on Earth.
4.2.1 The sources of this mass are:
1.6 This standard does not purport to address all of the
4.2.1.1 ANSI standard Z359.1.
safety concerns, if any, associated with its use. It is the
4.2.1.2 CEN standard EN1891.
responsibility of the user of this standard to establish appro-
4.3 Type III—136 6 1 kg.
priate safety and health practices and determine the applica-
4.3.1 The source of this mass is NFPAstandard NFPA1983.
bility of regulatory requirements prior to use.
4.4 Type IV—200 kg 61%.
2. Referenced Documents
4.4.1 The source of this mass is testing performed by the
British Columbia Council of Technical Rescue (BCCTR).
2.1 National Fire ProtectionAssociation (NFPA) Standard:
4.5 Type V—280 kg 61%.
NFPA 1983 Standard for Fire Service Life Safety Rope and
4.5.1 The source of this mass is testing performed by the
System Components
BCCTR. It is a metric conversion, rounded up, of the 272 kg
(600 lb) mass originally developed by the NFPA.
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
This specification is under the jurisdiction ofASTM Committee F32 on Search 4th Floor, New
...


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2266 − 03 (Reapproved 2015)
Standard Specification for
Masses Used in Testing Rescue Systems and Components
This standard is issued under the fixed designation F2266; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 American National Standards Institute (ANSI) Stan-
dard:
1.1 This specification defines the masses to be used when
ANSI Z359.1 Safety Requirements for Personal Fall Arrest
testing rescue systems and components.
Systems, Sub-Systems and Components
1.2 The masses represent personnel and equipment that may
2.3 European Committee for Standardization (CEN) Stan-
be attached to a rescue system or components. However, the
dard:
masses do not represent any particular type or kind of rescuer
EN1891 Personal Protective Equipment for the Prevention
or equipment.
of Falls from a Height—Low Stretch Kernmantel Ropes
1.2.1 The masses chosen have been used in the past or are
in current use in testing of rescue systems and components. 3. Terminology
Limiting testing to the masses listed in this specification allows
3.1 Definitions of Terms Specific to This Standard:
meaningful comparisons between past, current, and future test
3.1.1 rescue system, n—an assembly of ropes, cables, lines,
results.
and other components that may be used to raise, lower,
1.3 The values stated in SI units are to be regarded as suspend, support, or traverse persons or equipment during a
rescue.
standard. No other units of measurement are included in this
standard.
4. Classification
1.4 The user of this specification shall determine which
4.1 Type I—80 6 1 kg.
mass(es) represent(s) the personnel and equipment attached to
4.1.1 The source of this mass is the Union Internationale des
the system or component under test.
Associations d’Alpinisme (UIAA) and is the mass used in its
1.5 For the purposes of this specification, mass and weight
mountaineering equipment standards.
are synonymous when the object(s) representing the mass(es)
4.2 Type II—100 6 1 kg.
are weighed in air anywhere on Earth.
4.2.1 The sources of this mass are:
1.6 This standard does not purport to address all of the
4.2.1.1 ANSI standard Z359.1.
safety concerns, if any, associated with its use. It is the
4.2.1.2 CEN standard EN1891.
responsibility of the user of this standard to establish appro-
4.3 Type III—136 6 1 kg.
priate safety and health practices and determine the applica-
4.3.1 The source of this mass is NFPA standard NFPA 1983.
bility of regulatory requirements prior to use.
4.4 Type IV—200 kg 6 1 %.
2. Referenced Documents 4.4.1 The source of this mass is testing performed by the
British Columbia Council of Technical Rescue (BCCTR).
2.1 National Fire Protection Association (NFPA) Standard:
4.5 Type V—280 kg 6 1 %.
NFPA 1983 Standard for Fire Service Life Safety Rope and
4.5.1 The source of this mass is testing performed by the
System Components
BCCTR. It is a metric conversion, rounded up, of the 272 kg
(600 lb) mass originally developed by the NFPA.
Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
This specification is under the jurisdiction of ASTM Committee F32 on Search 4th Floor, New York, NY 10036, http://www.ansi.org.
and Rescue and is the direct responsibi
...


This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F2266 − 03 (Reapproved 2008) F2266 − 03 (Reapproved 2015)
Standard Specification for
Masses Used in Testing Rescue Systems and Components
This standard is issued under the fixed designation F2266; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—A units statement was added editorially as new 1.3 and the subsequent paragraphs were renumbered in Novem-
ber 2008.
1. Scope
1.1 This specification defines the masses to be used when testing rescue systems and components.
1.2 The masses represent personnel and equipment that may be attached to a rescue system or components. However, the masses
do not represent any particular type or kind of rescuer or equipment.
1.2.1 The masses chosen have been used in the past or are in current use in testing of rescue systems and components. Limiting
testing to the masses listed in this specification allows meaningful comparisons between past, current, and future test results.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The user of this specification shall determine which mass(es) represent(s) the personnel and equipment attached to the
system or component under test.
1.5 For the purposes of this specification, mass and weight are synonymous when the object(s) representing the mass(es) are
weighed in air anywhere on Earth.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
requirements prior to use.
2. Referenced Documents
2.1 National Fire Protection Association (NFPA) Standard:
NFPA 1983 Standard for Fire Service Life Safety Rope and System Components
2.2 American National Standards Institute (ANSI) Standard:
ANSI Z359.1 Safety Requirements for Personal Fall Arrest Systems, Sub-Systems and Components
2.3 European Committee for Standardization (CEN) Standard:
EN1891 Personal Protective Equipment for the Prevention of Falls from a Height—Low Stretch Kernmantel Ropes
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 rescue system, n—an assembly of ropes, cables, lines, and other components that may be used to raise, lower, suspend,
support, or traverse persons or equipment during a rescue.
4. Classification
4.1 Type I—80 6 1 kg.
4.1.1 The source of this mass is the Union Internationale des Associations d’Alpinisme (UIAA) and is the mass used in its
mountaineering equipment standards.
This specification is under the jurisdiction of ASTM Committee F32 on Search and Rescue and is the direct responsibility of Subcommittee F32.01 on Equipment, Testing,
and Maintenance.
Current edition approved Nov. 1, 2008Dec. 1, 2015. Published January 2009December 2015. Originally approved in 2003. Last previous edition approved in 20032008
ɛ1
as F2266 – 03.F2266 – 03 (2008) . DOI: 10.1520/F2266-03R08E01.10.1520/F2266-03R15.
Available from National Fire Protection Association (NFPA), 1 Batterymarch Park, Quincy, MA 02169-7471, http://www.nfpa.org.
Available from American National Standards
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3070-14(2022)(Guide)
Standard Guide for Evaluating Area Search Dog Crews or Teams

SIGNIFICANCE AND USE
4.1 An area search dog crew or team is required to have, at a minimum, the knowledge, skills, and abilities outlined within this document.  
4.1.1 An area search dog crew or team which meets the requirements in this guide is a Canine Search Resource of the category Area Search Dog as defined in Classification F1848 for Canine Search Resources.  
4.1.2 Additional differentiation of the specific Canine Search Resource is defined in Classification F1848 for Canine Search Resources.  
4.2 This guide only establishes the minimum knowledge, skills, and abilities required for an area search dog crew or team to perform area searches. No other skills are included or implied.  
4.3 This guide is an outline of the topics required for training or evaluating an area search dog team or crew, and may be used to assist in the development of a training document or program.  
4.4 This guide can be used to evaluate a document to determine if its content includes the topics necessary for training area search dog crews or teams. Likewise, this guide can be used to evaluate an existing training program to see if it meets the requirements in this guide.  
4.5 The knowledge, skills, and abilities presented in this guide are not in any particular order and do not represent a training sequence.  
4.6 Though this guide establishes minimum training requirements, it does not imply that an area search dog team or crew is a “trainee,” “probationary,” or other similarly termed part of an organization.  
4.6.1 The AHJ is responsible for determining the requirements and qualifications for its member ratings.  
4.7 An area search dog crew or team shall document training by completion of a position task book, compliant with Guide F3068, or by field demonstration under qualified supervision. Where proficiency in a skill or ability must be demonstrated, unless stated otherwise it shall be demonstrated for initial qualification, and then as often as required by the AHJ.
SCOPE
1.1 This guide defines the knowledge, skills, and abilities required for a dog crew or team to perform an area search.  
1.2 Area search dog crews or teams perform searches on the surface of the land, including open urban or wilderness areas, as well as mountainous terrain and alpine environments.  
1.2.1 Additional training shall be required for area search dog crews or teams that search in mountainous terrain, alpine environments, or underground.  
1.3 This guide does not include the knowledge, skills, and abilities required to search in partially or fully collapsed structures, confined spaces, or on bodies of water, inland or oceanic.  
1.4 Area search dog crews or teams trained to meet the requirements of this guide may operate in urban and disaster areas that may be isolated or have lost their infrastructure.  
1.5 Area search dog crews or teams must work under qualified supervision deemed appropriate by the AHJ.  
1.6 This guide does not provide a theoretical basis for how an area search dog crew or team functions.  
1.7 Search dog crews or teams are eligible to be members of Type I and II SAR crews or teams of the following Kinds, as defined in Classification F1993:  
1.7.1 Kind A (Wilderness),  
1.7.2 Kind B (Urban),  
1.7.3 Kind C (Mountainous),  
1.7.4 Kind G (Cave),  
1.7.5 Kind H (Mine),  
1.7.6 Kind I (Avalanche),  
1.7.7 Kind K (Aircraft), and  
1.7.8 Kind L (Unclassified).  
1.8 Further training may be required before an area search dog crew or team can fully participate on a particular Type and Kind of team or crew, based on specific local needs, regulations, or policies.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was develop...

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM F3144-15(2022)(Guide)
Standard Guide for Evaluating Trailing Search Dog Crews or Teams

SIGNIFICANCE AND USE
4.1 A trailing search dog crew or team is required to have, at a minimum, the knowledge, skills, and abilities outlined within this guide.  
4.1.1 A trailing search dog crew or team that meets the requirements of this guide is a Trailing Canine Search Resource, as defined in Classification F1848.  
4.2 Trailing search dogs that meet the requirements of this guide shall be tested by the AHJ using an aged trail of 6 to 12 h or as determined by the AHJ. Ages for competency trails shall take into consideration a minimum age, which should approximate the average response time for search dog crews.  
4.3 This guide only establishes the minimum knowledge, skills, and abilities required for a trailing search dog crew or team to perform trail searches. No other skills are included or implied.  
4.4 This guide is an outline of the topics required for training or evaluating a trailing search dog team or crew, and may be used to assist in the development of a training document or program.  
4.5 This guide can be used to evaluate a document to determine if its content includes the topics necessary for training trailing search dog crews or teams. Likewise, this guide can be used to evaluate an existing training program to see if it meets the requirements in this guide.  
4.6 The knowledge, skills, and abilities presented in this guide are not in any particular order and do not represent a training sequence.  
4.7 Though this guide establishes minimum training requirements, it does not imply that a trailing search dog team or crew is a “trainee,” “probationary,” or other similarly termed part of an organization.  
4.7.1 The AHJ is responsible for determining the requirements and qualifications for its member ratings.  
4.8 A trailing search dog crew or team shall document training by completion of a position task book, compliant with Guide F3068, or by field demonstration under qualified supervision. Where proficiency in a skill or ability must be demonstrated, unless oth...
SCOPE
1.1 This guide defines the knowledge, skills, and abilities required for a dog crew or team to perform a trailing search.  
1.2 Trailing search dog crews or teams perform searches on the surface of the land, including open urban or wilderness areas, as well as mountainous terrain and alpine environments.  
1.2.1 Additional training shall be required for trailing search dog crews or teams that search in mountainous terrain, alpine environments, and in caves, mines, and tunnels.  
1.3 This guide does not include the knowledge, skills, and abilities required to search in partially or fully collapsed structures, confined spaces, or on bodies of water, inland or oceanic.  
1.4 Trailing search dog crews or teams trained to meet the requirements of this guide may operate in urban and disaster areas that may be isolated or have lost their infrastructure.  
1.5 Trailing search dog crews or teams must work under qualified supervision deemed appropriate by the AHJ.  
1.6 Search dog crews or teams are eligible to be members of Type I and II SAR crews or teams of the following Kinds, as defined in Classification F1993:  
1.6.1 Kind A (Wilderness);  
1.6.2 Kind B (Urban);  
1.6.3 Kind C (Mountainous);  
1.6.4 Kind G (Cave);  
1.6.5 Kind H (Mine);  
1.6.6 Kind I (Avalanche);  
1.6.7 Kind K (Aircraft); and  
1.6.8 Kind L (Unclassified).  
1.7 Further training may be required before a trailing search dog crew or team can fully participate on a particular Type and Kind of team or crew, based on specific local needs, regulations, or policies.  
1.8 This guide does not provide a theoretical basis for how a trailing search dog crew or team functions.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory l...

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F3070-14(2022)(Guide)
Standard Guide for Evaluating Area Search Dog Crews or Teams

SIGNIFICANCE AND USE
4.1 An area search dog crew or team is required to have, at a minimum, the knowledge, skills, and abilities outlined within this document.  
4.1.1 An area search dog crew or team which meets the requirements in this guide is a Canine Search Resource of the category Area Search Dog as defined in Classification F1848 for Canine Search Resources.  
4.1.2 Additional differentiation of the specific Canine Search Resource is defined in Classification F1848 for Canine Search Resources.  
4.2 This guide only establishes the minimum knowledge, skills, and abilities required for an area search dog crew or team to perform area searches. No other skills are included or implied.  
4.3 This guide is an outline of the topics required for training or evaluating an area search dog team or crew, and may be used to assist in the development of a training document or program.  
4.4 This guide can be used to evaluate a document to determine if its content includes the topics necessary for training area search dog crews or teams. Likewise, this guide can be used to evaluate an existing training program to see if it meets the requirements in this guide.  
4.5 The knowledge, skills, and abilities presented in this guide are not in any particular order and do not represent a training sequence.  
4.6 Though this guide establishes minimum training requirements, it does not imply that an area search dog team or crew is a “trainee,” “probationary,” or other similarly termed part of an organization.  
4.6.1 The AHJ is responsible for determining the requirements and qualifications for its member ratings.  
4.7 An area search dog crew or team shall document training by completion of a position task book, compliant with Guide F3068, or by field demonstration under qualified supervision. Where proficiency in a skill or ability must be demonstrated, unless stated otherwise it shall be demonstrated for initial qualification, and then as often as required by the AHJ.
SCOPE
1.1 This guide defines the knowledge, skills, and abilities required for a dog crew or team to perform an area search.  
1.2 Area search dog crews or teams perform searches on the surface of the land, including open urban or wilderness areas, as well as mountainous terrain and alpine environments.  
1.2.1 Additional training shall be required for area search dog crews or teams that search in mountainous terrain, alpine environments, or underground.  
1.3 This guide does not include the knowledge, skills, and abilities required to search in partially or fully collapsed structures, confined spaces, or on bodies of water, inland or oceanic.  
1.4 Area search dog crews or teams trained to meet the requirements of this guide may operate in urban and disaster areas that may be isolated or have lost their infrastructure.  
1.5 Area search dog crews or teams must work under qualified supervision deemed appropriate by the AHJ.  
1.6 This guide does not provide a theoretical basis for how an area search dog crew or team functions.  
1.7 Search dog crews or teams are eligible to be members of Type I and II SAR crews or teams of the following Kinds, as defined in Classification F1993:  
1.7.1 Kind A (Wilderness),  
1.7.2 Kind B (Urban),  
1.7.3 Kind C (Mountainous),  
1.7.4 Kind G (Cave),  
1.7.5 Kind H (Mine),  
1.7.6 Kind I (Avalanche),  
1.7.7 Kind K (Aircraft), and  
1.7.8 Kind L (Unclassified).  
1.8 Further training may be required before an area search dog crew or team can fully participate on a particular Type and Kind of team or crew, based on specific local needs, regulations, or policies.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was develop...

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM F3144-15(2022)(Guide)
Standard Guide for Evaluating Trailing Search Dog Crews or Teams

SIGNIFICANCE AND USE
4.1 A trailing search dog crew or team is required to have, at a minimum, the knowledge, skills, and abilities outlined within this guide.  
4.1.1 A trailing search dog crew or team that meets the requirements of this guide is a Trailing Canine Search Resource, as defined in Classification F1848.  
4.2 Trailing search dogs that meet the requirements of this guide shall be tested by the AHJ using an aged trail of 6 to 12 h or as determined by the AHJ. Ages for competency trails shall take into consideration a minimum age, which should approximate the average response time for search dog crews.  
4.3 This guide only establishes the minimum knowledge, skills, and abilities required for a trailing search dog crew or team to perform trail searches. No other skills are included or implied.  
4.4 This guide is an outline of the topics required for training or evaluating a trailing search dog team or crew, and may be used to assist in the development of a training document or program.  
4.5 This guide can be used to evaluate a document to determine if its content includes the topics necessary for training trailing search dog crews or teams. Likewise, this guide can be used to evaluate an existing training program to see if it meets the requirements in this guide.  
4.6 The knowledge, skills, and abilities presented in this guide are not in any particular order and do not represent a training sequence.  
4.7 Though this guide establishes minimum training requirements, it does not imply that a trailing search dog team or crew is a “trainee,” “probationary,” or other similarly termed part of an organization.  
4.7.1 The AHJ is responsible for determining the requirements and qualifications for its member ratings.  
4.8 A trailing search dog crew or team shall document training by completion of a position task book, compliant with Guide F3068, or by field demonstration under qualified supervision. Where proficiency in a skill or ability must be demonstrated, unless oth...
SCOPE
1.1 This guide defines the knowledge, skills, and abilities required for a dog crew or team to perform a trailing search.  
1.2 Trailing search dog crews or teams perform searches on the surface of the land, including open urban or wilderness areas, as well as mountainous terrain and alpine environments.  
1.2.1 Additional training shall be required for trailing search dog crews or teams that search in mountainous terrain, alpine environments, and in caves, mines, and tunnels.  
1.3 This guide does not include the knowledge, skills, and abilities required to search in partially or fully collapsed structures, confined spaces, or on bodies of water, inland or oceanic.  
1.4 Trailing search dog crews or teams trained to meet the requirements of this guide may operate in urban and disaster areas that may be isolated or have lost their infrastructure.  
1.5 Trailing search dog crews or teams must work under qualified supervision deemed appropriate by the AHJ.  
1.6 Search dog crews or teams are eligible to be members of Type I and II SAR crews or teams of the following Kinds, as defined in Classification F1993:  
1.6.1 Kind A (Wilderness);  
1.6.2 Kind B (Urban);  
1.6.3 Kind C (Mountainous);  
1.6.4 Kind G (Cave);  
1.6.5 Kind H (Mine);  
1.6.6 Kind I (Avalanche);  
1.6.7 Kind K (Aircraft); and  
1.6.8 Kind L (Unclassified).  
1.7 Further training may be required before a trailing search dog crew or team can fully participate on a particular Type and Kind of team or crew, based on specific local needs, regulations, or policies.  
1.8 This guide does not provide a theoretical basis for how a trailing search dog crew or team functions.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory l...

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6152/D6152M-12(2024)(Specification)
Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing

ABSTRACT
This specification covers SEBS (styrene-ethylenebutylene-styrene)-modified mopping asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roofing systems. This specification is intended as a material specification and issues regarding the suitability of specific roof constructions or application techniques are beyond its scope. The specified tests and property values are intended to establish minimum properties. In place system design criteria or performance attributes are factors beyond the scope of this specification. The base asphalt shall be prepared from crude petroleum and the SEBS-modified asphalt shall incorporate sufficient SEBS as the primary polymeric modifier. The SEBS modified asphalt shall be homogeneous and free of water and shall conform to the prescribed physical properties including (1) softening point before and after heat exposure, (2) softening point change, (3) flash point, (4) penetration before and after heat exposure, (5) penetration change, (6) solubility in trichloroethylene, (7) tensile elongation, (8) elastic recovery, and (9) low temperature flexibility. The sampling and test methods to determine compliance with the specified physical properties, as well as the evaluation for stability during heat exposure are detailed.
SCOPE
1.1 This specification covers SEBS (styrene-ethylene-butylene-styrene)-modified asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems.  
1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond its scope.  
1.3 The specified tests and property values used to characterize SEBS-modified asphalt are intended to establish minimum properties. In-place system design criteria or performance attributes are factors beyond the scope of this specification.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5643/D5643M-06(2024)(Specification)
Standard Specification for Coal Tar Roof Cement, Asbestos Free

ABSTRACT
This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. The chemical composition of coal tar roof cement shall conform to the requirements prescribed. The water, non-volatile matter, insoluble matter, behaviour at 60 deg. C, adhesion to wet surfaces, and flash point shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D396-24(Specification)
Standard Specification for Fuel Oils

ABSTRACT
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial burners; Grades No. 1 S5000 and No. 1 S500 adapted to vaporizing type burners or where storage conditions require low pour point fuel; Grades No. 4 (Light) and No. 4 (Heavy) for use in commercial/industrial burners; and Grades No. 5 (Light), No. 5 (Heavy), and No. 6 for use in industrial burners. Preheating is usually required for handling and proper atomization. The grades of fuel oil shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter. Grades containing residual components shall remain uniform in normal storage and not separate by gravity into light and heavy oil components outside the viscosity limits for the grade. The grades of fuel oil shall conform to the limiting requirements prescribed for: (1) flash point, (2) water and sediment, (3) physical distillation or simulated distillation, (4) kinematic viscosity, (5) Ramsbottom carbon residue, (6) ash, (7) sulfur, (8) copper strip corrosion, (9) density, and (10) pour point. The test methods for determining conformance to the specified properties are given.
SCOPE
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:  
1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.  
1.1.2 Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.  
1.1.3 Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.  
1.1.4 Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.  
Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2: A more detailed description of the grades of fuel oils is given in X1.3.  
1.2 This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.  
1.3 Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8165-24(Test Method)
Standard Test Method for Evaluation of Load-Carrying Capacity of Lubricants Used in Hypoid Final-Drive Axles Operated under Low-Speed and High-Torque Conditions

SIGNIFICANCE AND USE
5.1 This test method measures a lubricant's ability to protect hypoid final drive axles from abrasive wear, adhesive wear, plastic deformation, and surface fatigue when subjected to low-speed, high-torque conditions. Lack of protection can lead to premature gear or bearing failure, or both.  
5.2 This test method is used, or referred to, in specifications and classifications of rear-axle gear lubricants such as:  
5.2.1 Specification D7450.  
5.2.2 American Petroleum Institute (API) Publication 1560.  
5.2.3 SAE J308.  
5.2.4 SAE J2360.
SCOPE
1.1 This test method, commonly referred to as the L-37-1 test, describes a test procedure for evaluating the load-carrying capacity, wear performance, and extreme pressure properties of a gear lubricant in a hypoid axle under conditions of low-speed, high-torque operation.3  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as National Pipe threads/diameters, tubing size, or where there is a sole source supply equipment specification.
1.2.1.1 The drawing in Annex A6 is in inch-pound units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 7.2 and 10.1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D6416/D6416M-16(2024)(Test Method)
Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load

SIGNIFICANCE AND USE
5.1 This test method simulates the hydrostatic loading conditions which are often present in actual sandwich structures, such as marine hulls. This test method can be used to compare the two-dimensional flexural stiffness of a sandwich composite made with different combinations of materials or with different fabrication processes. Since it is based on distributed loading rather than concentrated loading, it may also provide more realistic information on the failure mechanisms of sandwich structures loaded in a similar manner. Test data should be useful for design and engineering, material specification, quality assurance, and process development. In addition, data from this test method would be useful in refining predictive mathematical models or computer code for use as structural design tools. Properties that may be obtained from this test method include:  
5.1.1 Panel surface deflection at load,  
5.1.2 Panel face-sheet strain at load,  
5.1.3 Panel bending stiffness,  
5.1.4 Panel shear stiffness,  
5.1.5 Panel strength, and  
5.1.6 Panel failure modes.
SCOPE
1.1 This test method determines the two-dimensional flexural properties of sandwich composite plates subjected to a distributed load. The test fixture uses a relatively large square panel sample which is simply supported all around and has the distributed load provided by a water-filled bladder. This type of loading differs from the procedure of Test Method C393, where concentrated loads induce one-dimensional, simple bending in beam specimens.  
1.2 This test method is applicable to composite structures of the sandwich type which involve a relatively thick layer of core material bonded on both faces with an adhesive to thin-face sheets composed of a denser, higher-modulus material, typically, a polymer matrix reinforced with high-modulus fibers.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D3019/D3019M-17(2024)(Specification)
Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, and Fibered

ABSTRACT
This specification covers the physical requirements and testing of three types of lap cement for use with asphalt roll roofing. Type I is a brushing consistency lap cement intended for use in the exposed-nailing method of roll roofing application, and contains no mineral or other stabilizers. This type is further divided into two grades, as follows: Grade 1, which is made with an air-blown asphalt; and Grade 2, which is made with a vacuum-reduced or steam-refined asphalt. Both Types II and III, on the other hand, are heavy brushing or light troweling consistency lap cement intended for use in the concealed-nailing method of roll roofing application, only that Type II cement contains a quantity of short-fibered asbestos, while Type III cement contains a quantity of mineral or other stabilizers, or both, but contains no asbestos. The lap cements shall be sampled for testing, and shall adhere to specified values of the following properties: water content; distillation (total distillate at given temperatures); softening point of residue; solubility in trichloroethylene; and strength at indicated age.
SCOPE
1.1 This specification covers lap cement consisting of asphalt dissolved in a volatile petroleum solvent with or without mineral or other stabilizers, or both, for use with roll roofing. The fibered version of these cements excludes the use of asbestos fibers.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The following precautionary caveat applies only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off